EH / EH-N Miniature Lighted Pushbutton Switch

EH / EH-N Illunimated Pushbutton Switch EH Only 22.5mm depth behind panel with built-in resistor. ■ Depth behind panel：Only 22.5 mm ■ LED Full-Face, Dual-Color, Split-Face, Spot, Standby illumination available. ■ Terminal：#110 Tab・Soldering ■ Accessories：Guard covers, Sockets, Matrix fitting frame EH-N type Dust proof structure Actuation arm Guide EH-N type prevents dust from getting inside due to removed a conventional Silver contact (Gold-plated) / Cross-bar contact opening, installed a guide around the switch actuation arm. NC Switch connection C NO Light cartridge and Housing of EH-N and EH type are not interchangeable since they have different internal structures. Silent type Cross-bar contact Other specifications and replacement parts are the same. Switch connection C NO CHARACTERISTICS Button Size Square：□14　.2 　mm　　Rectangle：14.2×20.4 mm Contact Material Silver contact Cross-bar contact Connector type Connector type Silent type (Gold-plated) Silver contact (Gold-plated) Cross-bar contact Cross-bar contact (SPDT) (SPDT) AC 125 V 3 A AC 125 V 0.1 A AC 100V 1 A , DC 30 V 1A AC 100 V 0.1A, DC 30 V 0.1 A Rating (Resistive Load) AC 125 V 0.1 A AC 250 V 3 A DC 30 V 0.1 A (DPDT) (DPDT) DC 30 V 0.1 A AC 50V 1 A, DC 30 V 1 A AC 50V 0.1A, DC 30 V 0.1 A Insulation Resistance More than 100 MΩ at DC 500 V AC 1000 V RMS between AC 600 V RMS between AC 600 V RMS between NC and NO terminal NC and NO terminal Connector Connector NC and NO terminal Dielectric Strength AC 2000 V RMS between AC 1500 V RMS between terminals and ground terminals and ground AC 800 V RMS (DPDT AC 500 V) AC 600 V RMS (DPDT AC 500 V) AC 1500 V RMS between terminals and ground 50/60 Hz for 60 sec. at normal 50/60 Hz for 60 sec. at normal 50/60 Hz for 60 sec. at normal 50/60 Hz for 60 sec. at normal 50/60 Hz for 60 sec. at normal ambient temperature and humidity ambient temperature and humidity ambient temperature and humidity ambient temperature and humidity ambient temperature and humidity Less than 30 mΩ Less than 50 mΩ Less than 40 mΩ Less than 60 mΩ Less than 50 mΩ Contact Resistance (Initial value) (Initial value) Switch contact Less than 50 mΩ Switch contact Less then 50 mΩ (Initial value) at DC 6 V 1 A at DC 6 V 0.1 A at DC 6 V 1 A at DC 6 V 0.1 A at DC 6 V 0.1 A Vibration Resistance 10 to 55 Hz, Amplitude 1.5 mm Shock Resistance 300 m/s² max. (Malfunction) 500 m/s² max. (Destruction) Mechanical Momentary More than 2,000,000 operations More than 1,000,000 operations Life Alternate More than 200,000 operations Electrical Life (Resistive Load) More than 100,000 operations at max. rated load More than 100,000 operations Operating Force 4.41 N　max. 0.98 N　max. Total Travel 3 mm　max. Weight Square：8 g　　Rectangle：10 g Ambient Operating Temperature －15℃ to 50℃（No Freeze, No Condensation） Ambient Operating Humidity 80%RH max. （No Condensation） Ambient Storage Temperature －25℃ to 65℃（No Freeze, No Condensation） Ambient Storage Humidity 80%RH max. （No Condensation） http://www.sunmulon.co.jp/english/products/switch_e/eh.html ◇Demensions：page EH-4～6 ◇Accessories：page EH-7～8 ◇Ordering code：page EH-9～26 ◇Internal connection arrangements：page EH-29～31 ◇LED specifications：page EH-32～34 ◇Terminals / PCB hole cutout：page EH-35～36 ◇Mounting design / Panel cutout：page EH-37～38 ◇Accessories’ dimensions / Panel cutout：EH-39～45 Sunmulon Co., Ltd. EH-1

SPECIFICATIONS CONTACT RATINGS ILLUMINATION TYPES ● Silver contact (Gold-plated) EH EH-N Current (A) Common for each button size. Square A A Voltage (Resistive load) Button LED Color symbol 70 Red 80 Green 90 Yellow 14 Super Blue 16 Super White 18 Super Green Rectange A A AC 125 V 3 Full-Face A A ※ Yellow (90) is actually “ORANGE Yellow” not Lemon Yellow. 250 V 3 Dual-Color A A DC 8 V 3 Split-Face A A 14 V 3 Illumi nation Split-Face A A Full-Face 70 80 90 14 16 18 30 V 2 type Standby A N/A 125 V 0.4 Spot A N/A Non-illumination A N/A ● Cross-bar contact 70・80 70・14 70・16 70・18 80・90 90・70 SPDT A A AC 125 V 0.1 A (Resistive load) Rating Dual-Color DC 30 V 0.1 A (Resistive load) Contact DPDT A A 90・14 14・16 16・18 18・14 Silent type Minimum applicable load DC 5 V 1 mA (Resistive load) A A SPST（1a） #110 Tab Soldering A A 70 70 70 80 70 90 70 14 70 16 70 18 Term inal PCB A A Connector A A 80 70 80 80 80 90 90 70 90 80 90 90 UL A ※ N/A ※ Split-Face 90 14 14 14 14 16 14 18 14 70 14 90 Standard CSA A N/A RoHS（10 Substances) Conform to standards 16 14 16 16 16 18 16 70 18 14 18 16 A : Applicable N/A : Not applicable ※ Indicator type, Connector type, Silent type are not applicable. 18 18 18 70 STRUCTURE 70 70 70 70 70 70 LIGHT CARTRIDGE Full-Face Split-Face Standby Spot 70 80 90 14 16 18 Dual-Color 80 80 80 90 90 90 70 80 90 70 80 90 BUTTON Split-Face 90 14 14 14 14 14 14 14 16 18 70 90 Dimple Dimple 16 16 16 16 18 18 14 16 18 70 14 16 FILTER 18 18 18 70 Spot LED Color 4 Red 5 Green 6 Yellow Srandby LED UNIT Full-Face LED Color 70 Red 80 Green 90 Yellow Spot Spot LED Color 4 Red 5 Green 6 Yellow HOUSING EH EH-N EH EH-N EH EH Sunmulon Co., Ltd. EH-2

ILLUMINATION TYPES Common for each button size. LED Color symbol 70 Red 80 Green 90 Yellow 14 Super Blue 16 Super White 18 Super Green ※ Yellow (90) is actually “ORANGE Yellow” not Lemon Yellow. Full-Face 70 80 90 14 16 18 70・80 70・14 70・16 70・18 80・90 90・70 Dual-Color 90・14 14・16 16・18 18・14 70 70 70 80 70 90 70 14 70 16 70 18 80 70 80 80 80 90 90 70 90 80 90 90 Split-Face 90 14 14 14 14 16 14 18 14 70 14 90 16 14 16 16 16 18 16 70 18 14 18 16 18 18 18 70 70 70 70 70 70 70 70 80 90 14 16 18 80 80 80 90 90 90 70 80 90 70 80 90 Split-Face 90 14 14 14 14 14 14 14 16 18 70 90 16 16 16 16 18 18 14 16 18 70 14 16 18 18 18 70 Spot LED Color 4 Red 5 Green 6 Yellow Srandby Full-Face LED Color 70 Red 80 Green 90 Yellow Spot Spot LED Color 4 Red 5 Green 6 Yellow Sunmulon Co., Ltd. EH-3

DIMENSIONS ● With Flange Square □18.8 Full-Face □14.2 Standby Dual-Color Spot Split-Face Sunmulon mark Sunmulon mark 5 LED 2.8 0.5 3D □16.8 TOP VIEW TOP VIEW DXF ※3.9 for Dimple Button Rectangle 25 18.8 20.4 14.2 Full-Face Standby Dual-Color Spot Split-Face Sunmulon mark Sunmulon mark 5 LED 2.8 0.5 3D 23 16.8 TOP VIEW TOP VIEW DXF ※3.9 for Dimple Button ● Without Flange Square □14.2 Full-Face Standby Dual-Color Spot Split-Face Sunmulon mark Sunmulon mark 5 LED □16.8 0.5 3D DXF TOP VIEW TOP VIEW ※3.9 for Dimple Button Rectangle 20.4 14.2 Full-Face Standby Dual-Color Spot Split-Face Sunmulon mark Sunmulon mark 5 LED 0.5 3D 23 16.8 TOP VIEW TOP VIEW DXF ※3.9 for Dimple Button 3D・DXF data download site ： https://www.sunmulon.co.jp/download/ Tolerance : ± 0.4 mm Sunmulon Co., Ltd. EH-4 28.2 ※ 28.2 29 ※ 24.5 3 ※ 22.5 2 3 29 ※ 24.5 3 22.5 2 3 3.6 3.6 3.6 3.6 2 2 2 2

DIMENSIONS DIMENSIONS ● With Flange ● Connector for SPDT, Indicator Square □18.8 Full-Face Square □14.2 Standby Full-Face Standby Dual-Color Spot □18.8 Dual-Color Spot Split-Face □14.2 Split-Face Sunmulon mark Sunmulon mark ※ Sunmulon mark Sunmulon mark 5 LED 5 LED 13.9 2.8 0.5 3D □16.8 3D □16.8 TOP VIEW TOP VIEW ※3.9 for Dimple Button DXF ※3.9 for Dimple Button DXF TOP VIEW TOP VIEW Rectangle 25 18.8 20.4 14.2 Full-Face Rectangle Standby Full-Face 25 18.8 Standby Dual-Color Spot Dual-Color Split-Face 20.4 14.2 Spot Split-Face Sunmulon mark ※ Sunmulon mark Sunmulon mark Sunmulon mark 5 LED 5 LED 23 13.9 2.8 0.5 16.8 3D 23 16.8 TOP VIEW 3D TOP VIEW DXF ※3.9 for Dimple Button TOP VIEW TOP VIEW DXF ※3.9 for Dimple Button ● Without Flange ● Connector for DPDT Square □14.2 Full-Face Standby Square Dual-Color Full-Face Spot □18.8 Standby Split-Face □14.2 Dual-Color Spot Split-Face Sunmulon mark Sunmulon mark 5 LED Sunmulon mark Sunmulon mark 5 LED □16.8 0.5 3D □16.3 DXF TOP VIEW TOP VIEW ※3.9 for Dimple Button 3D DXF ※3.9 for Dimple Button TOP VIEW TOP VIEW Rectangle 20.4 14.2 Full-Face Standby Dual-Color Spot Rectangle 25 18.8 Full-Face Split-Face 20.4 14.2 Standby Dual-Color Spot Sunmulon mark Split-Face Sunmulon mark Sunmulon mark 5 LED Sunmulon mark 5 LED 0.5 3D 23 16.8 TOP VIEW TOP VIEW 23 16.8 DXF 3D ※3.9 for Dimple Button DXF ※3.9 for Dimple Button TOP VIEW TOP VIEW 3D・DXF data download site ： https://www.sunmulon.co.jp/download/ 3D・DXF data download site ： https://www.sunmulon.co.jp/download/ Tolerance : ± 0.4 mm Tolerance : ± 0.4 mm Sunmulon Co., Ltd. EH-5 28.2 ※ 28.2 29 ※ 24.5 3 ※ 22.5 2 3 29 ※ 24.5 3 22.5 2 3 3.6 3.6 3.6 3.6 2 2 2 2 (29.5) ※ 25.3 2 3 (29.5) ※ 29.5 25.3 2 3 23.5 2 3 29.5 23.5 2 3 3.6 3.6 3.6 3.6 2 2 2 2

D IMEN SIO NS ACCESSORIES ● Flat Indicator with Flange Name Appearance Classification Part no. Precautions for use Square □18.8 Full-Face Standby □14.2 Dual-Color Barrier Black EH-1084-K Spot Split-Face Short center barrier Gray EH-1084-H Sunmulon mark Sunmulon mark Black EH-1085-K LED Short side barrier 5 Gray EH-1085-H - Cannot be used with guard cover. Black EH-1086-K - Cannot be used with matrix fitting frame. Long center barrier Gray EH-1086-H Black EH-1087-K Long side barrier 2.8 0.5 □16.8 Gray EH-1087-H 3D TOP VIEW TOP VIEW DXF Black EH-1091-K Center barrier for Guard cover Gray EH-1091-H Rectangle Full-Face Standby - Use with guard cover as a set. 25 18.8 Dual-Color Spot - Cannot be used with matrix fitting frame. 20.4 14.2 Split-Face Black EH-1092-K 3D Side barrier Sunmulon mark Sunmulon mark DXF for Guard cover Gray EH-1092-H 5 LED Guard cover For use with barriers EH-1080 for square button - Use with barrires for guard cover as a set. - The cover to be opend 180°and returned by spring force. 3D For use with barriers - Cannot be used with matrix fitting frame. for rectangle button EH-1081 - Cannot be used with Dimple button. 2.8 0.5 DXF 23 16.8 3D TOP VIEW TOP VIEW Guard cover EH-1545-K DXF for without Flange Black For square button Gray EH-1545-H - The cover to be opened 180°and returned by spring force. ● Flat Indicator without Flange - Cannot be used with matrix fitting frame. Black EH-3409-K - Cannot be used with Dimple button. 3D For rectangle button Square Full-Face Standby DXF Gray EH-3409-H □14.2 Dual-Color Spot Split-Face Dust proof cover Sunmulon mark Sunmulon mark For square butoon DH-361 5 LED - Cannot be used with matrix fitting frame. - Cannot be used with Dimple button. For rectangle button EH-1083 0.5 □16.8 Matrix fitting frame Black EH-1610-K□ □ = number of switch（1～15） 3D TOP VIEW TOP VIEW For square button - Use with Flange and vertical mounting type DXF Gray EH-1610-H□ for the switch housing. - Only sockets can be used together. Rectangle Full-Face Black EH-1815-K□ - Cannot be used in combination with barriers, Standby 20.4 14.2 Dual-Color For rectangle button Spot guard cover, dustproof cover. Split-Face Gray EH-1815-H□ Sunmulon mark Sunmulon mark 5 LED Socket #110 Tab・ EH-1088-□ Soldering terminal Black EH-3210-2□ - Refer to the combination corresondence table on page EH-41. - Use #110 Tab・soldering terminal type 3D for the switch housing. PCB terminall Black EH-1196-□ 0.5 23 DXF 16.8 3D TOP VIEW TOP VIEW DXF 3D・DXF data download site ： https://www.sunmulon.co.jp/download/ 3D・DXF data download site ： https://www.sunmulon.co.jp/download/ Tolerance : ± 0.4 mm ◇Accessories’ dimensions / Panel cutout：EH-39～45 Sunmulon Co., Ltd. EH-6 28.2 28.2 29 24.5 0.9 2 0.9 2924.5 0.9 22.5 22.5 2 0.9 3.6 3.6 3.6 3.6 2 2 2 2

D IMEN SIO NS ACCESSORIES ● Flat Indicator with Flange Name Appearance Classification Part no. Precautions for use Square □18.8 Full-Face Standby □14.2 Dual-Color Barrier Black EH-1084-K Spot Split-Face Short center barrier Gray EH-1084-H Sunmulon mark Sunmulon mark Black EH-1085-K LED Short side barrier 5 Gray EH-1085-H - Cannot be used with guard cover. Black EH-1086-K - Cannot be used with matrix fitting frame. Long center barrier Gray EH-1086-H Black EH-1087-K Long side barrier 2.8 0.5 □16.8 Gray EH-1087-H 3D TOP VIEW TOP VIEW DXF Black EH-1091-K Center barrier for Guard cover Gray EH-1091-H Rectangle Full-Face Standby - Use with guard cover as a set. 25 18.8 Dual-Color Spot - Cannot be used with matrix fitting frame. 20.4 14.2 Split-Face Black EH-1092-K 3D Side barrier Sunmulon mark Sunmulon mark DXF for Guard cover Gray EH-1092-H 5 LED Guard cover For use with barriers EH-1080 for square button - Use with barrires for guard cover as a set. - The cover to be opend 180°and returned by spring force. 3D For use with barriers - Cannot be used with matrix fitting frame. for rectangle button EH-1081 - Cannot be used with Dimple button. 2.8 0.5 DXF 23 16.8 3D TOP VIEW TOP VIEW Guard cover EH-1545-K DXF for without Flange Black For square button Gray EH-1545-H - The cover to be opened 180°and returned by spring force. ● Flat Indicator without Flange - Cannot be used with matrix fitting frame. Black EH-3409-K - Cannot be used with Dimple button. 3D For rectangle button Square Full-Face Standby DXF Gray EH-3409-H □14.2 Dual-Color Spot Split-Face Dust proof cover Sunmulon mark Sunmulon mark For square butoon DH-361 5 LED - Cannot be used with matrix fitting frame. - Cannot be used with Dimple button. For rectangle button EH-1083 0.5 □16.8 Matrix fitting frame Black EH-1610-K□ □ = number of switch（1～15） 3D TOP VIEW TOP VIEW For square button - Use with Flange and vertical mounting type DXF Gray EH-1610-H□ for the switch housing. - Only sockets can be used together. Rectangle Full-Face Black EH-1815-K□ - Cannot be used in combination with barriers, Standby 20.4 14.2 Dual-Color For rectangle button Spot guard cover, dustproof cover. Split-Face Gray EH-1815-H□ Sunmulon mark Sunmulon mark 5 LED Socket #110 Tab・ EH-1088-□ Soldering terminal Black EH-3210-2□ - Refer to the combination corresondence table on page EH-41. - Use #110 Tab・soldering terminal type 3D for the switch housing. PCB terminall Black EH-1196-□ 0.5 23 DXF 16.8 3D TOP VIEW TOP VIEW DXF 3D・DXF data download site ： https://www.sunmulon.co.jp/download/ 3D・DXF data download site ： https://www.sunmulon.co.jp/download/ Tolerance : ± 0.4 mm ◇Accessories’ dimensions / Panel cutout：EH-39～45 Sunmulon Co., Ltd. EH-7 28.2 28.2 29 24.5 0.9 2 0.9 2924.5 0.9 22.5 22.5 2 0.9 3.6 3.6 3.6 3.6 2 2 2 2

ACCESSORIES Name Appearance Classification Part no. Precautions for use Relay board Common wiring is possible by simply connecting. Up to eight switch wires can be integrated onto CN9 For connector type EH-5246 a single board. ※Connection harnesses are not available from us. Connector For SPDT・Indicator EH-3251 Housing and contact set for connector type. ※Please specify whether or not to attach it by ordering code. For DPDT EH-5180 Wire harness 100cm EH-3250-1 For SPDT・Indicator 200cm EH-3250-2 Harness for connector type. 100cm EH-5177-1 For DPDT 200cm EH-5177-2 Removing tool For removal light cartridge SJ-0001 - Be used to remove light cartridge from housing. For removal flat indicator SJ-0009 - Be used to remove light cartridge of flat indicator from housing. ◇Accessories’ dimensions / Panel cutout：EH-39～45 Sunmulon Co., Ltd. EH-8 SJ-0009 Sunmulon 1 CN1 9 1 CN2 9 1 CN3 9 1 CN4 9 1 CN5 9 1 CN6 9 1 CN7 9 1 CN8 9 EH-5246

ACCESSORIES ORDERING CODE 【Full-Face】EH-N type Assembled Part (Light cartridge and Housing) Name Appearance Classification Part no. Precautions for use Relay board Common wiring is possible by simply connecting. EH N Up to eight switch wires can be integrated onto For connector type EH-5246 ● OPTION CN9 a single board. ※Connection harnesses are not available from us. ● OPERATION 0759 Low brightness ※5) L Indicator 001 Cathode common Connector F Flat Indicator 002 Vertical mounting For SPDT・Indicator EH-3251 Housing and contact set for connector type. S Momentary Slient type ※1) Blank No option M Momentary For other options except for the above, ※Please specify whether or not to attach it A Alternate please contact us. by ordering code. For DPDT EH-5180 ● Supply Voltage to LED ● CONTACT 1 DC 5V Built-in resistor ※5) 2 DC12V Built-in resistor ※5) Wire harness 100cm EH-3250-1 0 Indicator 3 DC24V Built-in resistor ※5) For SPDT・Indicator 1 SPST・Crossbar（Silent type only） ※1) 4 DC 5V Non-resistor 200cm EH-3250-2 3 SPDT・Silver (Gold-Plated) 5 DC12V Non-resistor Harness for connector type. 4 DPDT・Silver (Gold-Plated) 100cm EH-5177-1 6 ・ DC24V Non-resistor 5 SPDT Crossbar For DPDT X Without LED 6 DPDT・Crossbar 200cm EH-5177-2 For Non-resistor type, use external protective resistor. Removing tool ● BUTTON SHAPE For removal light cartridge SJ-0001 - Be used to remove light cartridge from housing. S0 Square ● TERMINAL K0 Square Dimple ※2) P ＃110 Tab・Soldering ※1) W0 Rectangle C PCB N0 Rectangle Dimple ※2) K Connector with Accessories ※4) 6) For removal flat indicator SJ-0009 - Be used to remove light cartridge of flat indicator from housing. N Connector without Accessories ※6) ● LED COLOR 70 Red ● BUTTON ● FILTER COLOR 80 Green COLOR 1 Red 90 Yellow ※3) R Red ● HOUSING COLOR 2 Green 14 Super-Blue G Green K Black ※6) 3 Yellow ※3) 16 Super-White Y Yellow ※3) H Gray ※6) 4 Milk-white 18 Super-Green M Milk-white KN Black without Flange 6 Blue X Without LED B Blue HN Gray without Flange X Without filter C Clear ※2) Generally, in case of using color button, For without button type, filter is not necessary. specify part numbers of light cartridge and housing separately. ● NOTES ※1）For Silent type, specify SPST・Crossbar (1) and #110 Tab・Soldering (P). ※2）Dimple button type is only clear color. Therefore, button color should be C (Clear). The guard cover and dust proof cover cannot be used for Dimple button. ※ 3 ）The color of “Yellow” for LED (90) and filter (3) is actually “Orange Yellow” not Lemon Yellow. ※ 4）For the connector, refer to Accessories page. ※ 5 ）For optional low brightness type (0759), specify supply voltage to LED 1, 2, or 3 (Built-in resistor type). ※ 6 ）For the connector, Housing without flange type cannot be selected. ◇Demensions：page EH-4～6 ◇Accessories：page EH-7～8 ◇Internal connection arrangements：page EH-29 ◇LED specifications：page EH-32 ◇Terminals / PCB hole cutout：page EH-35～36 ◇Accessories’ dimensions / Panel cutout：EH-39～45 ◇Mounting design / Panel cutout：page EH-37～38 ◇Accessories’ dimensions / Panel cutout：EH-39～45 Sunmulon Co., Ltd. EH-9 SJ-0009 Sunmulon 1 CN1 9 1 CN2 9 1 CN3 9 1 CN4 9 1 CN5 9 1 CN6 9 1 CN7 9 1 CN8 9 EH-5246

ORDERING CODE 【Full-Face】EH-N type EH-N and EH type are not interchangeable since they have different internal structures. Use the same type of Light cartridge and Housing in combination. LIGHT CARTRIDGE EH N ● OPTION ● BUTTON SHAPE 0759 Low brightness ※3) S0 Square 001 Cathode common K0 Square Dimple ※1) Blank No option For other options except for the above, W0 Rectangle please contact us. N0 Rectangle Dimple ※1) ● Supply Voltage to LED ● LED COLOR 1 DC 5V Built-in resistor ※3) 70 Red 2 DC12V Built-in resistor ※3) ● BUTTON COLOR 80 Green 3 DC24V Built-in resistor ※3) 90 Yellow ※2) R Red ● FILTER COLOR 4 DC 5V Non-resistor 14 Super-Blue G Green 1 Red 5 DC12V Non-resistor 16 Super-White Y Yellow ※2) 2 Green 6 DC24V Non-resistor 18 Super-Green M Milk-white 3 Yellow ※2) X Without LED X Without LED B Blue 4 Milk-white For Non-resistor type, C Clear ※1) use external protective resistor. 6 Blue X Without Button X Without filter Generally, in case of using color button, filter is not necessary. ● NOTES ※1）Dimple button type is only clear color. Therefore, button color should be C (Clear). The guard cover and dust proof cover cannot be used for Dimple button. ※2）The color of “Yellow” for LED (90) and filter (3) is actually “Orange Yellow” not Lemon Yellow. ※3）For optional low brightness type (0759), specify supply voltage to LED 1, 2, or 3 (Built-in resistor type). HOUSING EH N ● OPERATION ● OPTION L Indicator 002 Vertical Mounting F Flat Indicator Blank No option S Momentary Slient type ※1) M Momentary ● TERMINAL A Alternate P ＃110 Tab・Soldering ※1) C PCB K Connector with Accessories ※2) 3) ● CONTACT N Connector without Accessories ※3) 0 Indicator 1 SPST・Crossbar（Silent type only） ※1) ● HOUSING COLOR 3 SPDT・Silver (Gold-Plated) K Black ※3) 4 DPDT・Silver (Gold-Plated) ● BUTTON SHAPE H Gray ※3) 5 SPDT・Crossbar S0 Squ are KN Black without Flange 6 DPDT・Crossbar W0 Rectangle HN Gray without Flange ● NOTES ※1）For Silent type, specify SPST・Crossbar (1) and #110 Tab・Soldering (P). ※2）For the connector, refer to Accessories page. ※3）For the connector, Housing without flange type cannot be selected. Sunmulon Co., Ltd. EH-10

ORDERING CODE 【Full-Face】EH-N type ORDERING CODE 【Dual-Color】EH-N type EH-N and EH type are not interchangeable since they have different internal structures. Use the same type of Light cartridge and Housing in combination. Assembled Part (Light cartridge and Housing) LIGHT CARTRIDGE EH N EH N 1 2 ● OPTION ● OPTION ● BUTTON SHAPE 0759 Low brightness ※3) ● OPERATION S0 Square 001 Cathode common L Indicator 0759 Low brightness ※5) K0 Square Dimple ※1) Blank No option F Flat Indicator 001 Cathode common For other options except for the above, S Momentary Slient type ※1) 002 Vertical mounting W0 Rectangle please contact us. M Momentary Blank No option N0 Rectangle Dimple ※1) A Alternate For other options except for the above, ● Supply Voltage to LED please contact us. ● LED COLOR 1 DC 5V Built-in resistor ※3) ● Supply Voltage to LED 70 Red 2 DC12V Built-in resistor ※3) ● CONTACT 1 DC 5V Built-in resistor ※5) ● BUTTON COLOR 80 Green 3 DC24V Built-in resistor ※3) 0 Indicator 2 DC12V Built-in resistor ※5) 90 Yellow ※2) R Red ● FILTER COLOR 4 DC 5V Non-resistor 1 SPST・Crossbar（Silent type only） ※1) 3 DC24V Built-in resistor ※5) 14 Super-Blue G Green 1 Red 5 DC12V Non-resistor 3 SPDT・Silver (Gold-Plated) 4 DC 5V Non-resistor 16 Super-White Y Yellow ※2) 2 Green 6 DC24V Non-resistor 4 DPDT・Silver (Gold-Plated) 5 DC12V Non-resistor 18 Super-Green M Milk-white 3 Yellow ※2) X Without LED 5 SPDT・Crossbar 6 DC24V Non-resistor X Without LED B Blue 4 Milk-white For Non-resistor type, 6 DPDT・Crossbar X Without LED C Clear ※1) use external protective resistor. 6 Blue For Non-resistor type, X use external protective resistor. Without Button X Without filter ● BUTTON SHAPE ● TERMINAL Generally, in case of using color button, filter is not necessary. S3 Square P ＃110 Tab・Soldering ※1) K3 Square Dimple ※2) C PCB ● NOTES W3 Rectangle K Connector with Accessories ※4) 6) ※1）Dimple button type is only clear color. Therefore, button color should be C (Clear). N3 Rectangle Dimple ※2) N Connector without Accessories ※6) The guard cover and dust proof cover cannot be used for Dimple button. ※2）The color of “Yellow” for LED (90) and filter (3) is actually “Orange Yellow” not Lemon Yellow. ※ ） ● LED COLOR ● FILTER COLOR ※3) 3 For optional low brightness type (0759), specify supply voltage to LED 1, 2, or 3 (Built-in resistor type). 70 Red 4 Milk-White Put the color numbers 80 Green into frame 1 and 2. X Without filter 90 Yellow ● BUTTON （Dual-Color combination） 14 Super-Blue 7080・7014・7016 COLOR ※3) ● HOUSING COLOR 16 Super-White 7018・8090・9070・9014 C Clear ※2) K Black ※6) 1416・1618・1814 18 Super-Green M Milk-White H Gray ※6) HOUSING EH N Yellow (90) is actually “ORANGE Yellow” KN Black without Flange not Lemon Yellow. HN Gray without Flange ● OPERATION ● OPTION ● NOTES L Indicator ※1）For Silent type, specify SPST・Crossbar (1) For simultaneous lighting in Dual-Color 002 Vertical Mounting and #110 Tab・Soldering (P). F Flat Indicator Blank No option Simultaneous illumination is not possible for Built-in resistor type, cause heat. ※2）Dimple button type is only clear color. Please select Non-resistor type and apply required external resistor or socket S Momentary Slient type ※1) Therefore, button color should be C (Clear). for simultaneous lighting. M Momentary ● TERMINAL The guard cover and dust proof cover cannot be used for Dimple button. Simultaneous A Alternate P ＃110 Tab・Soldering ※1) Supply Voltage to LED lighting Lighting condition ※3）Button should be C (Clear) with Milk-white filter or C PCB M (Milk-white) without filter. 1 DC5V　Built-in resistor N/A 2 to 3 minutes possible. K Connector with Accessories ※2) 3) 2 DC12V Built-in resistor N/A 2 to 3 minutes possible. ● CONTACT ※4）For the connector, refer to Accessories page. N Connector without Accessories ※3) 3 DC24V Built-in resistor N/A 2 to 3 minutes possible. 0 Indicator ※ 5）For optional low brightness type (0759), specify Use external resistor 36Ω1/4W 1 SPST・Crossbar（Silent type only） ※1) ● HOUSING COLOR supply voltage to LED 1, 2, or 3 (Built-in resistor type). 4 DC 5V Non-resistor A or use socket EH-3210-2C 3 SPDT・Silver (Gold-Plated) K Black ※3) ※6）For the connector, Housing without flange type cannot be 5 DC12V Non-resistor A Use external resistor 270Ω1/4W ・ ● BUTTON SHAPE selected. H Gray ※3) or use socket EH-3210-2D 4 DPDT Silver (Gold-Plated) 5 SPDT・Crossbar S0 Squ are KN Black without Flange 6 DC24V Non-resistor A Use external resistor 1.1KΩ1/2W or use socket EH-3210-2E 6 DPDT・Crossbar W0 Rectangle HN Gray without Flange In case of Built-in resistor type with optional low brightness (0759) is possible for simultaneous lighting. ● NOTES ※1）For Silent type, specify SPST・Crossbar (1) and #110 Tab・Soldering (P). ※2）For the connector, refer to Accessories page. ◇Demensions：page EH-4～6 ◇Accessories：page EH-7～8 ※3）For the connector, Housing without flange type cannot be selected. ◇Internal connection arrangements：page EH-29 ◇LED specifications：page EH-32 ◇Terminals / PCB hole cutout：page EH-35～36 ◇Mounting design / Panel cutout：page EH-37～38 ◇Accessories’ dimensions / Panel cutout：EH-39～45 Sunmulon Co., Ltd. EH-11

ORDERING CODE 【Dual-Color】EH-N type EH-N and EH type are not interchangeable since they have different internal structures. Use the same type of Light cartridge and Housing in combination. LIGHT CARTRIDGE EH N 1 2 ● OPTION ● BUTTON SHAPE 0759 Low brightness ※3) 001 Cathode common S3 Square Blank No option K3 Square Dimple ※1) For other options except for the above, W3 Rectangle please contact us. N3 Rectangle Dimple ※1) ●Supply Voltage to LED ※4) 1 DC 5V Built-in resistor ※3) ● LED COLOR 2 DC12V Built-in resistor ※3) 3 DC24V Built-in resistor ※3) 70 Red Put the color numbers 80 Green 4 DC 5V Non-resistor into frame 1 and 2. 90 Yellow 5 DC12V Non-resistor （Dual-Color combination） 14 Super-Blue 6 7080・7014・ DC24V Non-resistor 7016 16 Super-White 7018・8090・9070・9014 ● BUTTON For Non-resistor type, 1416・1618・1814 use external protective resistor. 18 Super-Green COLOR ※2) Yellow (90) is actually “ORANGE Yellow” C Clear ※1) ● FILTER COLOR ※2) not Lemon Yellow. M Milk-white 4 Milk-white X Without button X Without filter ● NOTES ※1）Dimple button type is only clear color. Therefore, button color should be C (Clear). The guard cover and dust proof cover cannot be used for Dimple button. ※ 2 ）Button should be C (Clear) with Milk-white filter or M (Milk-white) without filter. ※ 3 ）For optional low brightness type (0759), specify supply voltage to LED 1, 2, or 3 (Built-in resistor type). ※4 ）For use with Simultaneous lighting, refer to page EH-11. HOUSING EH N ● OPERATION ● OPTION L Indicator 002 Vertical Mounting F Flat Indicator Blank No option S Momentary Slient type ※1) M Momentary ● TERMINAL A Alternate P ＃110 Tab・Soldering ※1) C PCB K Connector with Accessories ※2) 3) ● CONTACT N Connector without Accessories ※3) 0 Indicator 1 SPST・Crossbar（Silent type only） ※1) ● HOUSING COLOR 3 SPDT・Silver (Gold-Plated) K Black ※3) 4 DPDT・Silver (Gold-Plated) ● BUTTON SHAPE H Gray ※3) 5 SPDT・Crossbar S1 Squ are KN Black without Flange 6 DPDT・Crossbar W1 Rectangle HN Gray without Flange ● NOTES ※ 1）For Silent type, specify SPST・Crossbar (1) and #110 Tab・Soldering (P). ※2）For the connector, refer to Accessories page. ※3）For the connector, Housing without flange type cannot be selected. Sunmulon Co., Ltd. EH-12

ORDERING CODE 【Dual-Color】EH-N type ORDERING CODE 【Split-Face】EH-N type EH-N and EH type are not interchangeable since they have different internal structures. Use the same type of Light cartridge and Housing in combination. Assembled Part (Light cartridge and Housing) LIGHT CARTRIDGE EH N 1 2 EH N 1 2 C 1 2 ● OPTION ● OPTION ● OPERATION 0759 Low brightness ● BUTTON SHAPE 0759 Low brightness ※3) ※5) L Indicator 001 Cathode common 001 Cathode common S3 Square F Flat Indicator 002 Vertical mounting Blank No option K3 Square Dimple ※1) S Momentary Slient type ※2) For other options except for the above, Blank No option W3 Rectangle please contact us. M Momentary For other options except for the above, A Alternate please contact us. N3 Rectangle Dimple ※1) ●Supply Voltage to LED ※4) ● Supply Voltage to LED 1 DC 5V Built-in resistor ※3) ● CONTACT ● LED COLOR 2 DC12V Built-in resistor ※3) 1 DC 5V Built-in resistor 0 Indicator ※3) 2 DC12V Built-in resistor 70 Red 3 DC24V Built-in resistor 1 SPST・Crossbar（Silent type only） ※2) Put the color numbers 3 DC24V Built-in resistor ※5) 80 Green 4 DC 5V Non-resistor into frame 1 and 2. 3 SPDT・Silver (Gold-Plated) 90 Yellow 5 DC12V Non-resistor 4 Non-resistor （Dual-Color combination） 4 DPDT・Silver (Gold-Plated) X Without LED 14 Super-Blue 6 DC24V Non-resistor 7080・7014・7016 5 SPDT・Crossbar Super-White 7018・8090・9070・9014 ● BUTTON For Non-resistor type, For Non-resistor type, 16 1416・1618・1814 use external protective resistor. 6 DPDT・Crossbar use external protective resistor. 18 Super-Green COLOR ※2) ● TERMINAL Yellow (90) is actually “ORANGE Yellow” C Clear ※1) ● FILTER COLOR ※2) ● BUTTON SHAPE・ILLUMINATION TYPE P ＃110 Tab・Soldering ※2) not Lemon Yellow. M Milk-white 4 Milk-white S1 Square Vertical ※1) C PCB X Without button X Without filter S2 Square Horizontal K Connector with Accessories ※4) 6) K1 Square Dimple Vertical ※1) 3） N Connector without Accessories ※6) ● NOTES K2 Square Dimple Horizontal ※3） ※1）Dimple button type is only clear color. Therefore, button color should be C (Clear). W1 Rect. Vertical ※1) ● FILTER COLOR ※1) The guard cover and dust proof cover cannot be used for Dimple button. W2 Rect. Horizontal 1 Red ※ 2 ）Button should be C (Clear) with Milk-white filter or M (Milk-white) without filter. ※ 3 ）For optional low brightness type (0759), specify supply voltage to LED 1, 2, or 3 (Built-in resistor type). N1 Rect. Dimple Vertical ※1) 3） 2 Green 3 Yellow Put the color numbers ※4）For use with Simultaneous lighting, refer to page EH-11. N2 Rect. Dimple Horizontal ※3） into frame 1 and 2. 4 Milk-white ● LED COLOR ※1) 6 Blue 70 Red X Without filter：XX 80 Green Put the color numbers into frame 1 and 2. Without filter The combination of With filter and WIthout filter （Split-Face combination) 90 Yellow cannot be specified. 7070，7080，7090，7014，7016，7018， ● HOUSING COLOR 14 Super-Blue 8070，8080，8090，9070，9080，9090，9014， K Black ※6) 16 Super-White 1414，1416，1418，1470，1490，1614，1616， 1618，1670，1814，1816，1818，1870 ● BUTTON HOUSING N H Gray ※6) EH 18 Super-Green COLOR X Without LED：XX KN Black without Flange Without LED C Clear HN Gray without Flange The combination of With LED and Without LED cannot be specified. ● OPERATION ● OPTION ● NOTES L Indicator 002 Vertical Mounting ※1）How to specify the color of LED and filter For simultaneous lighting in Split-Face Select the color symbols listed in the ordering code, and put Simultaneous illumination is not possible for DC12V Built-in resistor type, cause heat. F Flat Indicator Blank No option them into the frame 1 and 2 referring to the figure below. Please select Non-resistor type and apply required external resistor or socket S Momentary Slient type ※1) The numbers in the figure match the location specified in the for simultaneous lighting. M Momentary ● TERMINAL ordering code. The color of “Yellow” for LED (90) and filter (3) is actually Supply Voltage to LED Simultaneous lighting Lighting condition A Alternate P ＃110 Tab・Soldering ※1) “Orange Yellow” not Lemon Yellow. A C PCB Vertical Split type terminal（L1、L2）and LED color 1 and 2 1 DC5V　Built-in resistor are opposite. 2 DC12V Built-in resistor N/A 2 to 3 minutes possible. K Connector with Accessories ※2) 3) Sunmulon mark Sunmulon mark Sunmulon mark Sunmulon mark ● CONTACT N/A Not specified N Connector without Accessories ※3) 3 DC24V Built-in resistor 1 1 A Only 0759 can be specified. 0 Indicator 1 2 1 2 1 SPST・Crossbar（Silent type only） ※1) ● HOUSING COLOR 2 2 Supply Voltage to LED Simultaneous Vertical Horizontal Vertical Horizontal lighting Lighting condition 3 SPDT・Silver (Gold-Plated) K Black ※3) ※2）For Silent type, specify SPST・Crossbar (1) ● BUTTON SHAPE DC 5V A Use external protective resistor. 4 DPDT・Silver (Gold-Plated) H Gray ※3) and #110 Tab・Soldering (P). ※3）The guard cover and dust proof cover cannot be used DC12V A Use external resistor 510Ω1/4W 5 SPDT・Crossbar S1 Square KN Black without Flange for Dimple button. 4 Non-resistor or use socket EH-3210-2A 6 DPDT・Crossbar W1 Rectangle HN Gray without Flange ※ 4 ）For the connector, refer to Accessories page. DC24V A Use external resistor 1.3kΩ1/2W ※5）DC24V Built-in resisor (3) can only be specified for option or use socket EH-3210-2B Low brightness (0759) . In case of Built-in resistor type with optional low brightness (0759) is possible for ● NOTES ※6 ）For the connector, Housing without flange type cannot be simultaneous lighting. selected. ※ 1）For Silent type, specify SPST・Crossbar (1) and #110 Tab・Soldering (P). ※2）For the connector, refer to Accessories page. ◇Demensions：page EH-4～6 ◇Accessories：page EH-7～8 ※3）For the connector, Housing without flange type cannot be selected. ◇Internal connection arrangements：page EH-30 ◇LED specifications：page EH-33 ◇Terminals / PCB hole cutout：page EH-35～36 ◇Mounting design / Panel cutout：page EH-37～38 ◇Accessories’ dimensions / Panel cutout：EH-39～45 Sunmulon Co., Ltd. EH-13

ORDERING CODE 【Split-Face】EH-N type EH-N and EH type are not interchangeable since they have different internal structures. Use the same type of Light cartridge and Housing in combination. LIGHT CARTRIDGE EH N 1 2 1 2 ● OPTION ● BUTTON SHAPE・ILLUMINATION TYPE 0759 Low brightness ※3) Square Vertical ※ 001 1) Cathode common S1 Blank No option S2 Square Horizontal For other options except for the above, K1 Square Dimple Vertical ※1, 2） please contact us. K2 Square Dimple Horizontal ※2） ● Supply Voltage to LED ※4) W1 Rect. Vertical ※1) 1 DC 5V Built-in resistor W2 Rect. Horizontal 2 DC12V Built-in resistor N1 Rect. Dimple Vertical ※1,2） 3 DC24V Built-in resistor ※3) N2 Rect. Dimple Horizontal ※2） 4 Non-resistor X Without LED ● LED COLOR ※1) For Non-resistor type, use external protective resistor. 70 Red 80 Green Put the color numbers into frame 1 and 2. ● FILTER COLOR ※1) （Split-Face combination) 90 Yellow 1 Red 7070，7080，7090，7014，7016，7018， 14 Super-Blue 8070，8080，8090，9070，9080，9090，9014， ● BUTTON COLOR 2 Green 16 Super-White 1414，1416，1418，1470，1490，1614，1616， 3 Yellow Put the color numbers 1618， 1670，1814，1816，1818，1870 C Clear into frame 1 and 2. 18 Super-Green X Without button 4 Milk-white X Without LED Without LED：XX 6 Blue The combination of With LED and Without LED cannot be specified. X Without filter Without filter：XX The combination of With filter and WIthout filter ● NOTES cannot be specified. ※1）How to specify the color of LED and filter Select the color symbols listed in the ordering code, and put them into the frame 1 and 2 referring to the figure below. The numbers in the figure match the location specified in the ordering code. The color of “Yellow” for LED (90) and filter (3) is actually “Orange Yellow” not Lemon Yellow. Vertical Split type terminal（L1、L2）and LED color 1 and 2 are opposite. ※2）The guard cover and dust proof cover cannot be used Sunmulon mark Sunmulon mark Sunmulon mark Sunmulon mark for Dimple button. 1 1 ※3）DC24V Built-in resisor (3) can only be specified for option 1 2 1 2 Low brightness (0759) . 2 2 ※4）For use with Simultaneous lighting, refer to page EH-13. Vertical Horizontal Vertical Horizontal HOUSING EH N ● OPTION ● OPERATION 002 Vertical Mounting L Indicator Blank No option F Flat Indicator S Momentary Slient type ※1) ● TERMINAL M Momentary P ＃110 Tab・Soldering ※1) A Alternate C PCB K Connector with Accessories ※2) 3) ● CONTACT N Connector without Accessories ※3) 0 Indicator 1 SPST・Crossbar（Silent type only） ※1) ● HOUSING COLOR 3 SPDT・Silver (Gold-Plated) K Black ※3) 4 DPDT・Silver (Gold-Plated) ● BUTTON SHAPE H Gray ※3) 5 SPDT・Crossbar S1 Squ are KN Black without Flange 6 DPDT・Crossbar W1 Rectangle HN Gray without Flange ● NOTES ※ 1）For Silent type, specify SPST・Crossbar (1) and #110 Tab・Soldering (P). ※2）For the connector, refer to Accessories page. ※3）For the connector, Housing without flange type cannot be selected. Sunmulon Co., Ltd. EH-14

ORDERING CODE 【Split-Face】EH-N type ORDERING CODE 【Full-Face】EH type EH-N and EH type are not interchangeable since they have different internal structures. Use the same type of Light cartridge and Housing in combination. Assembled Part (Light cartridge and Housing) LIGHT CARTRIDGE EH N 1 2 1 2 EH ● OPTION ● OPTION 0759 Low brightness ※3) ● OPERATION ● ・ 0759 Low brightness ※5) BUTTON SHAPE ILLUMINATION TYPE 001 Cathode common L Indicator 001 Cathode common S1 Square Vertical ※1) Blank No option F Flat Indicator 002 Vertical mounting S2 Square Horizontal For other options except for the above, S Momentary Slient type ※1) Blank No option K1 Square Dimple Vertical ※1, 2） please contact us. M Momentary For other options except for the above, K2 Square Dimple Horizontal ※2） ● Supply Voltage to LED ※4) A Alternate please contact us. W1 Rect. Vertical ※1) 1 DC 5V Built-in resistor ● Supply Voltage to LED W2 Rect. Horizontal 2 DC12V Built-in resistor N1 Rect. Dimple Vertical ※1,2） 3 DC24V Built-in resistor ※3) ● CONTACT 1 DC 5V Built-in resistor ※5) ※5) N2 Rect. Dimple Horizontal ※2） 2 DC12V Built-in resistor 4 Non-resistor 0 Indicator 3 DC24V Built-in resistor ※5) X Without LED 1 SPST・Crossbar（Silent type only） ※1) ● LED COLOR ※1) 4 DC 5V Non-resistor For Non-resistor type, use external protective resistor. 3 SPDT・Silver (Gold-Plated) 70 Red 5 DC12V Non-resistor 80 Green Put the color numbers into frame 1 and 2. ● FILTER COLOR ※1) 4 DPDT・Silver (Gold-Plated) 6 DC24V Non-resistor （Split-Face combination) 5 SPDT・Crossbar 90 Yellow 1 Red For Non-resistor type, 7070，7080，7090，7014，7016，7018， 6 DPDT・Crossbar 14 Super-Blue 8070，8080，8090，9070，9080，9090，9014， ● BUTTON COLOR 2 Green use external protective resistor. 16 Super-White 1414，1416，1418，1470，1490，1614，1616， 3 Yellow Put the color numbers 1618，1670，1814，1816，1818，1870 C Clear into frame 1 and 2. ● BUTTON SHAPE ● TERMINAL 18 Super-Green ： X Without button 4 Milk-white S0 Square P ＃110 Tab・Soldering ※1) X Without LED Without LED XX 6 Blue X Without filter Without filter：XX K0 Square Dimple ※2) C PCB The combination of With LED and Without LED cannot be specified. W0 Rectangle K Connector with Accessories ※4) 6) The combination of With filter and WIthout filter ● NOTES cannot be specified. N0 Rectangle Dimple ※2) N Connector without Accessories ※6) ※1）How to specify the color of LED and filter Select the color symbols listed in the ordering code, and put them into the frame 1 and 2 referring to the figure below. ● LED COLOR ● FILTER COLOR The numbers in the figure match the location specified in the ordering code. The color of “Yellow” for LED (90) and filter (3) is actually “Orange Yellow” not Lemon Yellow. 70 Red ● BUTTON 1 Red Vertical Split type terminal（L1、L2）and LED color 1 and 2 are opposite. 80 Green COLOR 2 Green ※2） Sunmulon mark Sunmulon mark Sunmulon mark The guard cover and dust proof cover cannot be used Sunmulon mark for Dimple button. 90 Yellow ※3) R Red ● HOUSING COLOR 3 Yellow ※3) 1 1 ※3）DC24V Built-in resisor (3) can only be specified for option 14 Super-Blue G Green K Black ※6) 4 Milk-white 1 2 1 2 Low brightness (0759) . 16 Super-White Y Yellow ※3) 2 2 H Gray ※6) 6 Blue ※4）For use with Simultaneous lighting, refer to page EH-13. 18 Super-Green M Milk-white X Without filter Vertical Horizontal Vertical Horizontal KN Black without Flange B Blue HN Gray without Flange Generally, in case of using color button, filter is not necessary. C Clear ※2) HOUSING EH N For without button type, specify part numbers of light cartridge and housing separately. ● OPTION ● OPERATION 002 Vertical Mounting L Indicator ● NOTES Blank No option F Flat Indicator ※1）For Silent type, specify SPST・Crossbar (1) and #110 Tab・Soldering (P). S Momentary Slient type ※1) ※2）Dimple button type is only clear color. Therefore, button color should be C (Clear). ● TERMINAL The guard cover and dust proof cover cannot be used for Dimple button. M Momentary P ＃110 Tab・Soldering ※1) ※ 3 ）The color of “Yellow” for LED (90) and filter (3) is actually “Orange Yellow” not Lemon Yellow. A Alternate C PCB ※ 4）For the connector, refer to Accessories page. K Connector with Accessories ※2) 3) ※ 5 ）For optional low brightness type (0759), specify supply voltage to LED 1, 2, or 3 (Built-in resistor type). ● CONTACT N Connector without Accessories ※3) ※ 6 ）For the connector, Housing without flange type cannot be selected. 0 Indicator 1 SPST・Crossbar（Silent type only） ※1) ● HOUSING COLOR 3 SPDT・Silver (Gold-Plated) K Black ※3) 4 DPDT・Silver (Gold-Plated) ● BUTTON SHAPE H Gray ※3) 5 SPDT・Crossbar S1 Squ are KN Black without Flange 6 DPDT・Crossbar W1 Rectangle HN Gray without Flange ● NOTES ※ 1）For Silent type, specify SPST・Crossbar (1) and #110 Tab・Soldering (P). ※2）For the connector, refer to Accessories page. ◇Demensions：page EH-4～6 ◇Accessories：page EH-7～8 ◇Internal connection arrangements：page EH-29 ◇LED specifications：page EH-32 ◇Terminals / PCB hole cutout：page EH-35～36 ※3）For the connector, Housing without flange type cannot be selected. ◇Mounting design / Panel cutout：page EH-37～38 ◇Accessories’ dimensions / Panel cutout：EH-39～45 Sunmulon Co., Ltd. EH-15

ORDERING CODE 【Full-Face】EH type EH-N and EH type are not interchangeable since they have different internal structures. Use the same type of Light cartridge and Housing in combination. LIGHT CARTRIDGE EH ● OPTION ● BUTTON SHAPE 0759 Low brightness ※3) S0 Square 001 Cathode common K0 Square Dimple ※1) Blank No option For other options except for the above, W0 Rectangle please contact us. N0 Rectangle Dimple ※1) ● Supply Voltage to LED ● LED COLOR 1 DC 5V Built-in resistor ※3) 70 Red 2 DC12V Built-in resistor ※3) ● BUTTON COLOR 80 Green 3 DC24V Built-in resistor ※3) 90 Yellow ※2) R Red ● FILTER COLOR 4 DC 5V Non-resistor 14 Super-Blue G Green 1 Red 5 DC12V Non-resistor 16 Super-White Y Yellow ※2) 2 Green 6 DC24V Non-resistor 18 Super-Green M Milk-white 3 Yellow ※2) For Non-resistor type, B Blue use external protective resistor. 4 Milk-white C Clear ※1) 6 Blue X Without button X Without filter Generally, in case of using color button, filter is not necessary. ● NOTES ※1）Dimple button type is only clear color. Therefore, button color should be C (Clear). The guard cover and dust proof cover cannot be used for Dimple button. ※2）The color of “Yellow” for LED (90) and filter (3) is actually “Orange Yellow” not Lemon Yellow. ※3）For optional low brightness type (0759), specify supply voltage to LED 1, 2, or 3 (Built-in resistor type). HOUSING EH ● OPERATION ● OPTION L Indicator 002 Vertical Mounting F Flat Indicator Blank No option S Momentary Slient type ※1) M Momentary ● TERMINAL A Alternate P ＃110 Tab・Soldering ※1) C PCB K Connector with Accessories ※2) 3) ● CONTACT N Connector without Accessories ※3) 0 Indicator 1 SPST・Crossbar（Silent type only） ※1) ● HOUSING COLOR 3 SPDT・Silver (Gold-Plated) K Black ※3) 4 DPDT・Silver (Gold-Plated) ● BUTTON SHAPE H Gray ※3) 5 SPDT・Crossbar S0 Squ are KN Black without Flange 6 DPDT・Crossbar W0 Rectangle HN Gray without Flange ● NOTES ※1）For Silent type, specify SPST・Crossbar (1) and #110 Tab・Soldering (P). ※2）For the connector, refer to Accessories page. ※3）For the connector, Housing without flange type cannot be selected. Sunmulon Co., Ltd. EH-16

ORDERING CODE 【Full-Face】EH type ORDERING CODE 【Dual-Color】EH type EH-N and EH type are not interchangeable since they have different internal structures. Use the same type of Light cartridge and Housing in combination. Assembled Part (Light cartridge and Housing) LIGHT CARTRIDGE EH EH 1 2 ● OPTION 0759 Low brightness ※3) ● OPERATION ● OPTION ● BUTTON SHAPE L Indicator 0759 Low brightness ※5) S0 Square 001 Cathode common ※ Blank No option F Flat Indicator 001 Cathode common K0 Square Dimple 1) For other options except for the above, S Momentary Slient type ※1) 002 Vertical mounting W0 Rectangle please contact us. M Momentary Blank No option N0 Rectangle Dimple ※1) A Alternate For other options except for the above, ● Supply Voltage to LED please contact us. ● LED COLOR 1 DC 5V Built-in resistor ※3) ● Supply Voltage to LED 70 Red 2 DC12V Built-in resistor ※3) ● CONTACT 1 DC 5V Built-in resistor ※5) ● BUTTON COLOR 80 Green 3 DC24V Built-in resistor ※3) 0 Indicator 2 DC12V Built-in resistor ※5) 90 Yellow ※2) R Red ● FILTER COLOR 4 DC 5V Non-resistor 1 SPST・Crossbar（Silent type only） ※1) 3 DC24V Built-in resistor ※5) 14 Super-Blue G Green 1 Red 5 DC12V Non-resistor 3 SPDT・Silver (Gold-Plated) 4 DC 5V Non-resistor 16 Super-White Y Yellow ※2) 2 Green 6 DC24V Non-resistor 4 DPDT・Silver (Gold-Plated) 5 DC12V Non-resistor 18 Super-Green M Milk-white 3 Yellow ※2) For Non-resistor type, 5 SPDT・Crossbar 6 DC24V Non-resistor B Blue use external protective resistor. 4 Milk-white 6 DPDT・Crossbar X Without LED C Clear ※1) 6 Blue For Non-resistor type, X use external protective resistor. Without button X Without filter ● BUTTON SHAPE ● TERMINAL Generally, in case of using color button, filter is not necessary. S3 Square P ＃110 Tab・Soldering ※1) K3 Square Dimple ※2) C PCB ● NOTES W3 Rectangle K Connector with Accessories ※4) 6) ※1）Dimple button type is only clear color. Therefore, button color should be C (Clear). N3 Rectangle Dimple ※2) N Connector without Accessories ※6) The guard cover and dust proof cover cannot be used for Dimple button. ※2）The color of “Yellow” for LED (90) and filter (3) is actually “Orange Yellow” not Lemon Yellow. ● LED COLOR ● FILTER COLOR ※3) ※3）For optional low brightness type (0759), specify supply voltage to LED 1, 2, or 3 (Built-in resistor type). 70 Red 4 Milk-White Put the color numbers 80 Green into frame 1 and 2. X Without filter 90 Yellow ● BUTTON （Dual-Color combination） 14 Super-Blue 7080・7014・7016 COLOR ※3) ● HOUSING COLOR 16 Super-White 7018・8090・9070・9014 C Clear ※2) K Black ※6) 1416・1618・1814 18 Super-Green M Milk-White H Gray ※6) HOUSING EH Yellow (90) is actually “ORANGE Yellow” KN Black without Flange not Lemon Yellow. HN Gray without Flange ● OPERATION ● OPTION ● NOTES For simultaneous lighting in Dual-Color L Indicator ※1）For Silent type, specify SPST・Crossbar (1) 002 Vertical Mounting and #110 Tab・Soldering (P). F Flat Indicator Blank No option Simultaneous illumination is not possible for Built-in resistor type, cause heat. ※2）Dimple button type is only clear color. Please select Non-resistor type and apply required external resistor or socket S Momentary Slient type ※1) Therefore, button color should be C (Clear). for simultaneous lighting. M Momentary ● TERMINAL The guard cover and dust proof cover cannot be used for Dimple button. A Alternate P ＃110 Tab・Soldering ※1) Supply Voltage to LED Simultaneous lighting Lighting condition ※3）Button should be C (Clear) with Milk-white filter or C PCB M (Milk-white) without filter. 1 DC5V　Built-in resistor N/A 2 to 3 minutes possible. K Connector with Accessories ※2) 3) 2 DC12V Built-in resistor N/A 2 to 3 minutes possible. ● CONTACT ※4）For the connector, refer to Accessories page. N Connector without Accessories ※3) 3 DC24V Built-in resistor N/A 2 to 3 minutes possible. 0 Indicator ※ 5）For optional low brightness type (0759), specify 4 DC 5V Non-resistor A Use external resistor 36Ω1/4W 1 SPST・Crossbar（Silent type only） ※1) ● HOUSING COLOR supply voltage to LED 1, 2, or 3 (Built-in resistor type). or use socket EH-3210-2C 3 SPDT・Silver (Gold-Plated) K Black ※3) ※6）For the connector, Housing without flange type cannot be 5 DC12V Non-resistor A Use external resistor 270Ω1/4W ・ ● BUTTON SHAPE H Gray ※ selected. 3) or use socket EH-3210-2D 4 DPDT Silver (Gold-Plated) 5 SPDT・Crossbar S0 Squ are KN Black without Flange 6 DC24V Non-resistor A Use external resistor 1.1KΩ1/2W or use socket EH-3210-2E 6 DPDT・Crossbar W0 Rectangle HN Gray without Flange In case of Built-in resistor type with optional low brightness (0759) is possible for simultaneous lighting. ● NOTES ※1）For Silent type, specify SPST・Crossbar (1) and #110 Tab・Soldering (P). ※2）For the connector, refer to Accessories page. ◇Demensions：page EH-4～6 ◇Accessories：page EH-7～8 ※3）For the connector, Housing without flange type cannot be selected. ◇Internal connection arrangements：page EH-29 ◇LED specifications：page EH-32 ◇Terminals / PCB hole cutout：page EH-35～36 ◇Mounting design / Panel cutout：page EH-37～38 ◇Accessories’ dimensions / Panel cutout：EH-39～45 Sunmulon Co., Ltd. EH-17

ORDERING CODE 【Dual-Color】EH type EH-N and EH type are not interchangeable since they have different internal structures. Use the same type of Light cartridge and Housing in combination. LIGHT CARTRIDGE EH 1 2 ● OPTION ● BUTTON SHAPE 0759 Low brightness ※3) 001 Cathode common S3 Square Blank No option K3 Square Dimple ※1) For other options except for the above, W3 Rectangle please contact us. N3 Rectangle Dimple ※1) ●Supply Voltage to LED ※4) 1 DC 5V Built-in resistor ※3) ● LED COLOR 2 DC12V Built-in resistor ※3) 70 Red 3 DC24V Built-in resistor ※3) Put the color numbers 80 Green 4 DC 5V Non-resistor into frame 1 and 2. 90 Yellow 5 DC12V Non-resistor （Dual-Color combination） 14 Super-Blue 6 7080・ ・ DC24V Non-resistor 7014 7016 16 Super-White 7018・8090・9070・9014 ● BUTTON For Non-resistor type, 1416・1618・1814 use external protective resistor. 18 Super-Green COLOR ※2) Yellow (90) is actually “ORANGE Yellow” C Clear ※1) ● FILTER COLOR ※2) not Lemon Yellow. M Milk-white 4 Milk-white X Without button X Without filter ● NOTES ※1）Dimple button type is only clear color. Therefore, button color should be C (Clear). The guard cover and dust proof cover cannot be used for Dimple button. ※ 2 ）Button should be C (Clear) with Milk-white filter or M (Milk-white) without filter. ※ 3 ）For optional low brightness type (0759), specify supply voltage to LED 1, 2, or 3 (Built-in resistor type). ※4 ）For use with Simultaneous lighting, refer to page EH-11. HOUSING EH ● OPERATION ● OPTION L Indicator 002 Vertical Mounting F Flat Indicator Blank No option S Momentary Slient type ※1) M Momentary ● TERMINAL A Alternate P ＃110 Tab・Soldering ※1) C PCB K Connector with Accessories ※2) 3) ● CONTACT N Connector without Accessories ※3) 0 Indicator 1 SPST・Crossbar（Silent type only） ※1) ● HOUSING COLOR 3 SPDT・Silver (Gold-Plated) K Black ※3) 4 DPDT・Silver (Gold-Plated) ● BUTTON SHAPE H Gray ※3) 5 SPDT・Crossbar S1 Squ are KN Black without Flange 6 DPDT・Crossbar W1 Rectangle HN Gray without Flange ● NOTES ※ 1）For Silent type, specify SPST・Crossbar (1) and #110 Tab・Soldering (P). ※2）For the connector, refer to Accessories page. ※3）For the connector, Housing without flange type cannot be selected. Sunmulon Co., Ltd. EH-18

ORDERING CODE 【Dual-Color】EH type ORDERING CODE 【Split-Face】EH type EH-N and EH type are not interchangeable since they have different internal structures. Use the same type of Light cartridge and Housing in combination. Assembled Part (Light cartridge and Housing) LIGHT CARTRIDGE EH 1 2 EH 1 2 C 1 2 ● OPTION ● OPTION ● OPERATION 0759 Low brightness ※5) ● BUTTON SHAPE 0759 Low brightness ※3) L Indicator 001 Cathode common 001 Cathode common S3 Square F Flat Indicator 002 Vertical mounting ※ Blank No option K3 Square Dimple 1) S Momentary Slient type ※2) For other options except for the above, Blank No option W3 Rectangle please contact us. M Momentary For other options except for the above, please contact us. N3 Rectangle Dimple ※1) ●Supply Voltage to LED ※4) A Alternate ● Supply Voltage to LED 1 DC 5V Built-in resistor ※3) ● CONTACT ● LED COLOR 2 DC12V Built-in resistor ※3) 1 DC 5V Built-in resistor 0 Indicator 70 Red 3 DC24V Built-in resistor ※3) 2 DC12V Built-in resistor 1 SPST・Crossbar（Silent type only） ※2) Put the color numbers ※5) 80 Green 4 DC 5V Non-resistor 3 DC24V Built-in resistor into frame 1 and 2. 3 SPDT・Silver (Gold-Plated) 4 Non-resistor 90 Yellow 5 DC12V Non-resistor （Dual-Color combination） 4 DPDT・Silver (Gold-Plated) 6 For Non-resistor type, 14 Super-Blue ・ ・ DC24V Non-resistor 7080 7014 7016 5 SPDT・Crossbar use external protective resistor. Super-White 7018・8090・9070・9014 ● BUTTON For Non-resistor type, 16 1416・1618・1814 use external protective resistor. 6 DPDT・Crossbar ● TERMINAL 18 Super-Green COLOR ※2) Yellow (90) is actually “ORANGE Yellow” C Clear ※1) ● FILTER COLOR ※2) ● BUTTON SHAPE・ILLUMINATION TYPE P ＃110 Tab・Soldering ※2) not Lemon Yellow. C PCB M Milk-white 4 Milk-white S1 Square Vertical ※1) K Connector with Accessories ※4) 6) X Without button X Without filter S2 Square Horizontal N Connector without Accessories ※6) K1 Square Dimple Vertical ※1) 3） ● NOTES K2 Square Dimple Horizontal ※3） ● FILTER COLOR ※1) ※1）Dimple button type is only clear color. Therefore, button color should be C (Clear). W1 Rect. Vertical ※1) 1 Red The guard cover and dust proof cover cannot be used for Dimple button. W2 Rect. Horizontal 2 Green ※ 2 ）Button should be C (Clear) with Milk-white filter or M (Milk-white) without filter. N1 Rect. Dimple Vertical ※1) 3） 3 Yellow Put the color numbers ※3）For optional low brightness type (0759), specify supply voltage to LED 1, 2, or 3 (Built-in resistor type). into frame 1 and 2. ※4 ）For use with Simultaneous lighting, refer to page EH-11. N2 Rect. Dimple Horizontal ※3） 4 Milk-white 6 Blue ● LED COLOR ※1) X Without filter Without filter：XX 70 Red Put the color numbers into frame 1 and 2. The combination of With filter and WIthout filter 80 Green （Split-Face combination) cannot be specified. 90 Yellow 7070，7080，7090，7014，7016，7018， 8070，8080，8090，9070，9080，9090，9014， ● HOUSING COLOR 14 Super-Blue 1414，1416，1418，1470，1490，1614，1616， 16 Super-White 1618，1670，1814，1816，1818，1870 K Black ※6) ● BUTTON HOUSING Without LED：XX COLOR H Gray ※6) EH 18 Super-Green KN Black without Flange The combination of With LED and Without LED cannot be specified. C Clear HN Gray without Flange ● OPERATION ● OPTION ● NOTES L Indicator ※1）How to specify the color of LED and filter For simultaneous lighting in Split-Face 002 Vertical Mounting Select the color symbols listed in the ordering code, and put Simultaneous illumination is not possible for DC12V Built-in resistor type, cause heat. F Flat Indicator Blank No option them into the frame 1 and 2 referring to the figure below. Please select Non-resistor type and apply required external resistor or socket S Momentary Slient type ※1) The numbers in the figure match the location specified in the for simultaneous lighting. M Momentary ● TERMINAL ordering code. The color of “Yellow” for LED (90) and filter (3) is actually Supply Voltage to LED Simultaneous lighting Lighting condition A Alternate P ＃110 Tab・Soldering ※1) “Orange Yellow” not Lemon Yellow. Vertical Split type terminal（L1、L2）and LED color 1 and 2 1 DC5V　Built-in resistor A C PCB are opposite. 2 DC12V Built-in resistor N/A 2 to 3 minutes possible. K Connector with Accessories ※2) 3) Sunmulon mark Sunmulon mark Sunmulon mark Sunmulon mark ● CONTACT N/A Not specified N Connector without Accessories ※3) 3 DC24V Built-in resistor A Only 0759 can be specified. 0 Indicator 1 1 1 2 1 2 ● HOUSING COLOR 2 2 1 SPST・Crossbar（Silent type only） ※1) Simultaneous Vertical Horizontal Vertical Horizontal Supply Voltage to LED lighting Lighting condition 3 SPDT・Silver (Gold-Plated) K Black ※3) ※2）For Silent type, specify SPST・Crossbar (1) ● BUTTON SHAPE DC 5V A Use external protective resistor. 4 DPDT・Silver (Gold-Plated) H Gray ※3) and #110 Tab・Soldering (P). 5 SPDT・Crossbar S1 Squ are KN Black without Flange ※3）The guard cover and dust proof cover cannot be used DC12V A Use external resistor 510Ω1/4W for Dimple button. 4 Non-resistor or use socket EH-3210-2A 6 DPDT・Crossbar W1 Rectangle HN Gray without Flange ※ 4 ）For the connector, refer to Accessories page. DC24V A Use external resistor 1.3kΩ1/2W ※5）DC24V Built-in resisor (3) can only be specified for option or use socket EH-3210-2B Low brightness (0759) . In case of Built-in resistor type with optional low brightness (0759) is possible for ● NOTES ※6 ）For the connector, Housing without flange type cannot be simultaneous lighting. selected. ※ 1）For Silent type, specify SPST・Crossbar (1) and #110 Tab・Soldering (P). ※2）For the connector, refer to Accessories page. ◇Demensions：page EH-4～6 ◇Accessories：page EH-7～8 ※3）For the connector, Housing without flange type cannot be selected. ◇Internal connection arrangements：page EH-30 ◇LED specifications：page EH-33 ◇Terminals / PCB hole cutout：page EH-35～36 ◇Mounting design / Panel cutout：page EH-37～38 ◇Accessories’ dimensions / Panel cutout：EH-39～45 Sunmulon Co., Ltd. EH-19

ORDERING CODE 【Split-Face】EH type EH-N and EH type are not interchangeable since they have different internal structures. Use the same type of Light cartridge and Housing in combination. LIGHT CARTRIDGE EH 1 2 1 2 ● OPTION ● BUTTON SHAPE・ILLUMINATION TYPE 0759 Low brightness ※3) S1 Square Vertical ※ 001 1) Cathode common Blank No option S2 Square Horizontal For other options except for the above, K1 Square Dimple Vertical ※1, 2） please contact us. K2 Square Dimple Horizontal ※2） ● Supply Voltage to LED ※4) W1 Rect. Vertical ※1) 1 DC 5V Built-in resistor W2 Rect. Horizontal 2 DC12V Built-in resistor N1 Rect. Dimple Vertical ※1,2） 3 DC24V Built-in resistor ※3) N2 Rect. Dimple Horizontal ※2） 4 Non-resistor For Non-resistor type, use external protective resistor. ● LED COLOR ※1) 70 Red ● FILTER COLOR ※1) 80 Green Put the color numbers into frame 1 and 2. 1 Red （Split-Face combination) 90 Yellow 7070，7080，7090，7014，7016，7018， 2 Green 14 Super-Blue 8070，8080，8090，9070，9080，9090，9014， ● BUTTON COLOR 3 Yellow Put the color numbers 1414，1416，1418，1470，1490，1614，1616， into frame 1 and 2. 16 Super-White 1618，1670，1814，1816，1818，1870 C Clear 4 Milk-white 18 Super-Green X Without button 6 Blue X Without filter Without filter：XX The combination of With filter and WIthout filter cannot be specified. ● NOTES ※1）How to specify the color of LED and filter Select the color symbols listed in the ordering code, and put them into the frame 1 and 2 referring to the figure below. The numbers in the figure match the location specified in the ordering code. The color of “Yellow” for LED (90) and filter (3) is actually “Orange Yellow” not Lemon Yellow. Vertical Split type terminal（L1、L2）and LED color 1 and 2 are opposite. ※2）The guard cover and dust proof cover cannot be used Sunmulon mark Sunmulon mark Sunmulon mark Sunmulon mark for Dimple button. 1 1 ※3）DC24V Built-in resisor (3) can only be specified for option 1 2 1 2 Low brightness (0759) . 2 2 ※4）For use with Simultaneous lighting, refer to page EH-19. Vertical Horizontal Vertical Horizontal HOUSING EH ● OPTION ● OPERATION 002 Vertical Mounting L Indicator Blank No option F Flat Indicator S Momentary Slient type ※1) ● TERMINAL M Momentary P ＃110 Tab・Soldering ※1) A Alternate C PCB K Connector with Accessories ※2) 3) ● CONTACT N Connector without Accessories ※3) 0 Indicator 1 SPST・Crossbar（Silent type only） ※1) ● HOUSING COLOR 3 SPDT・Silver (Gold-Plated) K Black ※3) 4 DPDT・Silver (Gold-Plated) ● BUTTON SHAPE H Gray ※3) 5 SPDT・Crossbar S1 Squ are KN Black without Flange 6 DPDT・Crossbar W1 Rectangle HN Gray without Flange ● NOTES ※ 1）For Silent type, specify SPST・Crossbar (1) and #110 Tab・Soldering (P). ※2）For the connector, refer to Accessories page. ※3）For the connector, Housing without flange type cannot be selected. Sunmulon Co., Ltd. EH-20