Tyco社　W28シリーズ

Catalog 1308242 Issued 3-03 (PDF Rev. 10-10) W28 series Push to Reset Fuseholder-Type Thermal P&B Circuit Breaker Note: VDE not available on 16A and 20A W28 only. Features Resettable Overload Capacity: Six times rated current for 0.25 through • Push to reset. 2 amp models. Ten times rated current • Approved to many international standards. for 3 through 20 amp models. • Replaces slow blow glass cartridge fuse. Reset Time: 180 seconds max. for 0.25 through 2 amp models. 5 to 30 • Labor-saving snap-in mounting. seconds for 3 through 20 amp models. • Button extends for visual trip indication. Agency Approvals W28 series is UL 1077 Recognized as Supplementary Protectors, File E69543, and CSA Accepted as Supplementary Protectors (Appliance Typical Resistance vs. Current Rating @ +25°C Component Protectors), File LR15734. W28 breakers are VDE approved for use in office equipment (AC loads only) and provides Current Typical Current Typical 8mm isolation. 16 amp and 20 amp models do not have VDE Rating Resistance Rating Resistance approvals at present. in Amps in Ohms in Amps in Ohms 0.25 14.0 8.0 0.016 Users should thoroughly review the technical data before selecting a product part 0.50 3.55 9.0 0.014 number. It is recommended that users also seek out the pertinent approvals files of the agencies/laboratories and review them to confirm the product meets the 0.75 2.0 10.0 0.011 requirements for a given application. 1.0 0.89 11.0 0.01 2.0 0.17 12.0 0.009 3.0 0.069 13.0 0.009 4.0 0.043 14.0 0.007 5.0 0.030 15.0 0.007 6.0 0.026 16.0 0.007 7.0 0.017 20.0 0.006 Electrical Data @ 25°C Calibration:Will continuously carry 100% of rating. 3-20 amp models – may trip between 101% and 134%, but must trip at 135% of rating within one hour at +25°C. Mechanical/Environmental Data 0.25-2 amp models – may trip between 101% and 174%, but Termination: .250” (6.35mm) quick connects. Soldering to terminals is must trip at 175% of rating within one hour at +25°C. not recommended. Dielectric Strength: Over 1,500 volts RMS. Mounting: Snaps into panel from front. See Recommended Maximum Operating Voltages: 32VDC; 250VAC, 50/60 Hz. Panel Cutouts. Interrupt Capacity: 1,000 amps at 250VAC, 50/60 Hz. and 32VDC in Approximate Weight: 0.35 oz. (10g). accordance with UL standard 1077. Time vs. Current Trip Curve @ +25°C Ambient Compensation Chart 1000 1.40 (A) All 3-20 Amp Models (B) All 0.25-2 Amp Models 900 Overload Trip Times Overload Trip Times 1.30 100% No Trip 100% No Trip 1.20 800 135% Trip in 1 hour 175% Trip in 1 hour 200% 2.2-15.0 Sec. 200% 4.5-28.0 Sec. 1.10 400% 0.55-1.8 Sec. 400% 1.0-6.5 Sec. 700 600% 0.27-0.7 Sec. 600% 0.4-4.0 Sec. 1.00 800% 0.17-0.45 Sec. (A) 1000% 0.12-0.3 Sec. 600 0.90 0.80 500 0.70 400 0.60 –20 –10 0 10 20 30 40 50 60 (B) 300 Ambient Temperature In Degrees Centigrade (°C) 200 To use this chart: Read up from the ambient temper- 175 ature to the curve, and across to find a correction fac- 135 100 tor. Multiply the breaker rating by the correction fac- tor to determine the compensated rating. Calculate 0 the overloads in terms of the compensated rating to .1 1 10 100 1000 use the published trip curve. Time In Seconds Do not use these devices outside their specified operating temperature ranges. Dimensions are shown for Dimensions are in inches over Specifications and availability www.tycoelectronics.com 110 reference purposes only. (millimeters) unless otherwise subject to change. Technical support: specified. Refer to inside back cover. Load Current As A Percent Of Breaker Rating Correction Factor

Catalog 1308242 Issued 3-03 (PDF Rev. 10-10) Ordering Information Typical Part Number > W 28 -X Q 1 A -5 1. Designator: W = Circuit breaker 2. Series Number: 28 = Single Pole Fuseholder Type 3. Circuit Function: X = Series Trip, Push-to-Reset Button 4. Terminal Type and Mounting: Q = .250” (6.35mm) Quick Connect will mount in .032”-.062” (.813mm – 1.574mm) thick panel. T = .250” (6.35mm) Quick Connect will mount in .075”-.105” (1.905mm – 2.667mm) thick panel. For panel thicknesses other than above, order “Q” type and 55-025B Internal Tooth Push-On Lockwasher. 5. Bezel Color: 1 = Black with White Rate Marking 11 = Black with No Rate Marking 2 = Red with Black Rate Marking 21 = Red with No Rate Marking B = Black with White “Reset” Marked On Bezel (No Rate Marking) Consult factory for other bezel colors. 6. Button Color: A = Black B = Red Consult factory for other button colors. 7. Amp Rating: 0.25 0.75 2 4 6 8 10 12 14 20 0.50 1 3 5 7 9 11 13 16 Note: All standard part numbers in this series are RoHS compliant. Stock Items – Authorized distributors are more likely to stock the following items. W28-XQ1A-0.25 W28-XQ1A-1 W28-XQ1A-4 W28-XQ1A-7 W28-XQ1A-12 W28-XT1A-10 W28-XQ1A-0.50 W28-XQ1A-2 W28-XQ1A-5 W28-XQ1A-8 W28-XQ1A-15 W28-XT1A-12 W28-XQ1A-0.75 W28-XQ1A-3 W28-XQ1A-6 W28-XQ1A-10 W28-XQ1A-20 Outline Dimensions Optional Protective Boot Push-to-Reset Type Clear Silicone Rubber Boot 23-019A 1.535 MAX. .19 .76 MAX. (38.99) (4.83) (19.31) A A I .54 MAX. .76 MAX. (13.716) (19.31) O .325 MAX. .37 (8.26) AMP RATING (9.4) .350 (8.89) .525 .625 MAX. (13.33) (15.875) .750 (19.05) SECTION A-A .250 x .032 (6.35 x .813) QUICK CONNECT TERMINALS Optional Internal Tooth Push-On Lockwasher Notes: 1. Soldering to terminals is not recommended. For panels greater than .105 (2.67) thickness 55-025B 2. Recommended Panel Thickness: Style Q: .032” - .062” (.813 mm - 1.574 mm) Style T: .075” - .105” (1.905 mm - 2.667 mm) 3. Internal tooth push-on washer available for panel thickness not covered above. 55-025B .970 DIA. INTERNAL TOOTH (25.64) PUSH-ON LOCKWASHER Recommended Panel Cutouts For panels greater than .105” (2.67) thickness .570-.575 .540-.550 (14.478-14.605) (13.716-13.970) Disclaimer While Tyco Electronics has made every reasonable effort to ensure the accuracy .625-.635 .625-.635 .625-.635 of the information in this document , Tyco Electronics does not guarantee that it (15.875-16.129) (15.875-16.129) (15.875-16.129) is error-free, nor does Tyco Electronics make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. Tyco Electronics reserves the right to make any adjustments to the information contained herein at any time without notice. Tyco Electronics expressly dis- claims all implied warranties regarding the information contained herein, includ- ing, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in this catalog are for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult Tyco Electronics for the latest dimensions and design specifications. Dimensions are shown for Dimensions are in inches over Specifications and availability www.tycoelectronics.com reference purposes only. (millimeters) unless otherwise subject to change. Technical support: 111 specified. Refer to inside back cover.