高硬度鋼加工用ボールエンドミル　エポックディープボールエボリューションハード-TH3　EPDBEH-TH3（株式会社MOLDINO）のカタログ無料ダウンロード | Apérza Catalog（アペルザカタログ）

ドキュメント名	高硬度鋼加工用ボールエンドミル　エポックディープボールエボリューションハード-TH3　EPDBEH-TH3
ドキュメント種別	製品カタログ
ファイルサイズ	3.2Mb
登録カテゴリ	設備・消耗品・その他工具・測量器具切削工具エンドミル
取り扱い企業	株式会社MOLDINO (この企業の取り扱いカタログ一覧)

Page1

高硬度鋼加工用ボールエンドミル Ball End Mill for Hardened Steel エポックディープボールエボリューションハード-TH3 Epoch Deep Ball Evolution Hard-TH3 EPDBEH-TH3 焼きばめホルダに適したショートシャンクタイプを新発売図、表等のデータは試験結果の一例であり、保証値ではありません。「　　　　　　　」は株式会社MOLDINOの登録商標です。 RE1.25以下の全サイズ対象 The diagrams and table data are examples of test results, and are not guaranteed values. “ ” is a registered trademark of MOLDINO Tool Engineering, Ltd. 外径実測値ラベル表記をスタート安全上のご注意 Attentions on Safety 1. 取扱上のご注意 1. Cautions regarding handling New short shank type for shrink-fit tool holders （１）工具をケース（梱包）から取り出す際は、工具の飛び出し、落下にご注意ください。特に工具刃部との接 (1) When removing the tool from its case (packaging), be careful that the tool does not pop out or is 　触には十分ご注意をお願いします。 dropped. Be particularly careful regarding contact with the tool flutes. （２）鋭利な切れ刃を有する工具を取扱う際は、切れ刃を素手で直接触れないように注意してください。 Introduction of labeling showing actual tool diameter (2) When handling tools with sharp cutting flutes, be careful not to touch the cutting flutes directly with 2. 取付け時のご注意 your bare hands. (for all sizes up to RE1.25) （１）ご使用前に、工具の傷・割れ等の外観確認を行っていただき、コレットチャック等への取付けは確実に 2. Cautions regarding mounting 行ってください。　 (1) Before use, check the outside appearance of the tool for scratches, cracks, etc. and that it is firmly （２）ご使用中に、異常な振動等が発生した場合は、直ちに機械を停止させて、その振動の原因を取り除い mounted in the collet chuck, etc. 　てください。 (2) If abnormal chattering, etc. occurs during use, stop the machine immediately and remove the cause 3. 使用上のご注意 of the chattering. （１）切削工具あるいは被削材の寸法・回転の方向は、あらかじめ確認しておいてください。 3. Cautions during use （２）標準切削条件表の数値は、新しい作業の立上げの目安としてご利用ください。切込みが大きい場合、 (1) Before use, confirm the dimensions and direction of rotation of the tool and milling work material. 使用機械の剛性が小さい場合あるいは被加工物の性状に応じて切削条件を適正に調整してご使用 (2) The numerical values in the standard cutting conditions table should be used as criteria when starting ください。 new work. The cutting conditions should be adjusted as appropriate when the cutting depth is large, （３）切削工具材料は硬質の材料です。ご使用中に破損して飛散する場合があります。また、切りくずが飛 the rigidity of the machine being used is low, or according to the conditions of the work material. 散することがあります。これらの飛散物等は作業者を切傷させ、火傷あるいは目に入って負傷させる恐 (3) Cutting tools are made of a hard material. During use, they may break and fly off. In addition, cutting れがありますので、工具をご使用中はその周囲に安全カバーを取付け、保護めがね等の保護具を着用 chips may also fly off. Since there is a danger of injury to workers, fire, or eye damage from such して安全な環境下での作業をお願いいたします。 flying pieces, a safety cover should be attached when work is performed and safety equipment such （４）切削中に発生する火花や、破損による発熱や、切りくずによる引火・火災の危険があります。引火や as safety goggles should be worn to create a safe environment for work. 爆発の危険のあるところでは使用しないでください。不水溶性切削液をご使用される場合は防火対 (4) There is a risk of fire or inflammation due to sparks, heat due to breakage, and cutting chips. Do not 策を必ず行なってください。 use where there is a risk of fire or explosion. Please caution of fire while using oil base coolant, fire （５）工具を本来の目的以外にはご使用にならないでください。 prevention is necessary. 4. 再研削時のご注意 (5) Do not use the tool for any purpose other than that for which it is intended. （１）再研削時期が不適当であると工具が破損する恐れがあります。適正な工具と交換するか、再研削を 4. Cautions regarding regrinding 行ってください。（２）工具を再研削しますと粉塵が発生します。再研削時にはその周囲に安全カバーを取付け、保護め (1) If regrinding is not performed at the proper time, there is a risk of the tool breaking. Replace the tool がね等の保護具を着用してください。 with one in good condition, or perform regrinding. （3）本製品には特定化学物質に指定されたコバルト及びその無機化合物が含まれています。再研削等の (2) Grinding dust will be created when regrinding a tool. When regrinding, be sure to attach a safety 　　加工を加える場合は特定化学物質障害予防規則(特化則)に従った取扱いをしてください。 cover over the work area and wear safety clothes such as safety goggles, etc. (3) This product contains the specified chemical substance cobalt and its inorganic compounds. When 5. 工具に関して、安全上の問題点・不明の点・その他相談がありましたら　フ　リ　ーダ　イ　ヤ　ル　技　術　相　談　へ　 performing regrinding or similar processing, be sure to handle the processing in accordance with 　ご相談ください。　 thelocal laws and regulations regarding prevention of hazards due to specified chemical substances. ホームページフリーダイヤル技術相談 https://www.moldino.com MOLDINO Tool Engineering, Ltd. 本社〒130-0026 東京都墨田区両国4-31-11（ヒューリック両国ビル８階）工具選定データベース【 TOOLSEARCH】 03-6890-5101 FAX 03-6890-5134 International Sales Dept .: +81-3-6890-5103 FAX +81-3-6890-5128 営業企画部 ☎03-6890-5102 FAX03-6890-5134 海外営業部 ☎03-6890-5103 FAX03-6890-5128 東京営業所 ☎03-6890-5110 FAX03-6890-5133 静岡営業所 ☎054-273-0360 FAX054-273-0361 東北営業所 ☎022-208-5100 FAX022-208-5102 名古屋営業所 ☎052-687-9150 FAX052-687-9144 新潟営業所 ☎0258-87-1224 FAX0258-87-1158 大阪営業所 ☎06-7668-0190 FAX06-7668-0194 東関東営業所 ☎0294-88-9430 FAX0294-88-9432 中四営業所 ☎082-536-2001 FAX082-536-2003 長野営業所 ☎0268-21-3700 FAX0268-21-3711 九州営業所 ☎092-289-7010 FAX092-289-7012 北関東営業所 ☎0276-59-6001 FAX0276-59-6005 神奈川営業所 ☎046-400-9429 FAX046-400-9435 ヨーロッパ／MOLDINO Tool Engineering Europe GmbH Itterpark 12, 40724 Hilden, Germany. TEL : +49-(0)2103-24820, FAX : +49-(0)2103-248230 アメリカ／MITSUBISHI MATERIALS U.S.A. CORPORATION 41700 Gardenbrook Road, Suite 120, Novi, MI 48375-1320 U.S.A. TEL : +1(248)308-2620, FAX :+1(248)308-2627 メキシコ／MMC METAL DE MEXICO, S.A. DE C.V. Av. La Cañada No.16, Parque Industrial Bernardo Quintana, El Marques, Querétaro, CP 76246, México TEL : +52-442-1926800 　　 MOLDINO Tool Engineering, Ltd. ブラジル／MMC METAL DO BRASIL LTDA. Rua Cincinato Braga, 340 13° andar.Bela Vista – CEP 01333-010 São Paulo – SP ., Brasil TEL : +55(11)3506-5600 FAX : +55(11)3506-5677 　　タ　　イ／MMC Hardmetal (Thailand) Co.,Ltd. MOLDINO Division 622 Emporium Tower, Floor 22/1-4, Sukhumvit Road, Klongton, Klongtoey, Bangkok 10110, Thailand TEL:+66-(0)2-661-8175 FAX:+66-(0)2-661-8176 インド／MMC Hardmetal India Pvt Ltd. H.O.: Prasad Enclave, #118/119, 1st Floor, 2nd Stage, 5th main, BBMP Ward #11, (New #38), Industrial Suburb, Yeshwanthpura, Bengaluru, 560 022, Karnataka, India. Tel : +91-80-2204-3600 New Produc t News No.1701-16 2024-12 掲載価格は2024年12月2日改定後の消費税抜きの単価を表示しております。予告なく、改良・改善のために仕様変更することがあります。 Specifications for the products listed in this catalog are subject to change without notice due to ベジタブルインクで印刷しています。 2024-12（K）HGT2 replacement or modification. Printed using vegetable oil ink. Printed in JAPAN 2017-1:FP

Page2

新開発した次世代ハードコーティング特長 Features 02 高硬度鋼加工用に刃形を適正化　ダブルフェイス形状 Optimized cutting edge geometry "double-face" for hardened steel machining. TH3コーティングを採用高硬度鋼の加工において図ダブルフェイス形状図ボール刃形断面概略図（A-B断面） Figure : Double Face geometry Figure : A-B cross section view 優れた耐摩耗性を発揮ボール刃逃げ面を2つの面で形成従来刃形 Conventional geometry Flank of ball area has double face (two-stage flank) Applies newly developed next-generation hard coating "TH3 Coating" Excellent wear resistance when machining hardened steel A B 逃げ面 Flank face すくい面 Rake face 先端拡大摩耗の進行方向 2段目逃げ面 Wear progress direction EPDBEH-TH3の特長 2nd flank face Magnified view Features of EPDBEH-TH3 ダブルフェイス形状 Double face geometry 1段目逃げ面 1st flank face 逃げ面 01 高硬度鋼加工用TH3コーティング Flank face すくい面 "TH3 Coating" for hardened steel machining Rake face ダブルフェイス形状で工具摩滅を抑制 1段目逃げ面が摩耗進行を抑制 02 高硬度鋼加工用刃形ダブルフェイス形状 Double-face effect prevents shape from deteriorating First flank face suppresses wear progression Double-face cutting edge geometry for hardened steel machining ※RE2以上はダブルフェイス形状ではありません Double face geometry is not applied to RE2 or larger size 03 高精度加工を追求した工具設計 Tool design to pursue high-accuracy machining 特長 Features 03 高精度加工を追求した工具設計 Tool design to pursue high-accuracy machining RE0.5-首下長10mmの場合バックドラフト形状 Back draft effect 従来首形状対比10% TH3コーティング TH3 Coating 加工のたわみを抑制バックドラフトの効果で良好な加工 EPDBEH-TH3 面品位が得られます。用途（当社計算理論値）炭素鋼ステンレス鋼プリハードン鋼焼入れ鋼焼入れ鋼焼入れ鋼 Applications 合金鋼工具鋼 45～55HRC 55～65HRC 65～72HRC 金型製作部品加工 RE0.05～RE6［ 331 アイテム］バックドラフト形状（強バックテーパ） Carbon steel Stainless steel Pre-hardened Hardened steel Hardened steel Hardened steel Alloy steel Tool steel steel 45̃55HRC 55̃65HRC 65̃72HRC Mold making Parts processing Items In case of R0.5 - under neck length 10mm, を継承。点あたりで切削するので 10% of deflection is suppressed compared to conventional neck ビビりが低減できます。 shape Backdraft effect enables good-quality (Theoretical value by our calculation) processed surfaces to be achieved. 特長 01 高硬度鋼加工用 TH3コーティング Inherits the reliable backdraft shape to enable Features chattering to be reduced by performing point "TH3 Coating " for hardened steel machining cutting. 特長及び性能 Features and performance 皮膜構造 Coating structure ポケット立ち壁仕上げ加工評価結果 Evaluation of cutting remain in pocket wall finishing test ● 優れた耐摩耗性・耐熱性を有する高硬度皮膜優れた耐熱衝撃性を ● 優れた耐衝撃性を有し、突発的な欠損を抑制有する機能皮膜図壁面削り残り量 Figure. Cutting remain amount of wall surface Funcitional layer with excellent 被削材 Work material： YXR33(58HRC) ● 焼入れ鋼など50HRCを超える高硬度鋼の加工領域において長寿命 thermal shock resistance 機　　械 Machine ：立型MC(HSK-E32) Vertical MC ・High hardness coating with excellent wear resistance and heat resistance 0.04 0.0395 優れた耐摩耗性、 0.0369 工　　具 Tool ：EPDBEH2010-6-TH3 ・Has excellent thermal shock resistance enables to suppress sudden chipping 耐熱性を有する新皮膜・Long tool life when cutting high-hardness materials (50HRC or higher) such as hardened steel 切削条件：n=22,600min-1New layer with excellent wear resistance and heat resistance Cutting conditions 0.03 　(vc=71m/min) ターゲットとなる鋼種 Target steel grade ナノ組織を採用 0.0256 　vf=820mm/min Applies nano-size composition 　(fz=0.018mm/t) ● 焼入れ鋼などの高硬度鋼（特に50HRC以上）、ハイス鋼超硬母材 Carbide 0.02 　ap=0.03mm ae=0.01 mm ・Hardened steel (especially 50HRC or higher), high-speed steel 　OH＝18mm　ミスト Mist 13mm 0.01 11mm ! “TH3”のココがポイント！ 5mm 新皮膜は“ナノ組織”の適用により、皮膜の破壊単位を小さくする事に成功！ Point New coating achieves to reduce destruction unit of layer by applying "nano-size composition". ポケットサイズ Pocket size： 0 従来皮膜 13×11×5mm（立ち壁 Wall） Conventional coating 大きく破壊新皮膜 New coating EPDBEH-TH3 従来品1 従来品2 Conventional 1 Conventional 2 Big destruction 切削抵抗切削抵抗小さく破壊 Small destruction 首部の剛性を高めることでたわみを抑制でき、従来比30%の削り残り量削減 Cutting force Cutting force By increasing the neck rigidity, it is possible to suppress deflection and reduce the cutting remain by 30% than conventional design 従来のエポックディープエボリューションシリーズ（EPDBEHやEPDBE）と比較すると実有効首下長が短くなっております。干渉領域をチェックした上でご使用お願いします。 Effective neck length is shorter than existing Epoch Deep Evolution series (EPDBEH, EPDBE). Please use with checking interference area. ⇒ 干渉チェックはCAD/CAMサポートデータパックをご使用ください。詳細は弊社ホームページをご覧ください超硬母材 Carbide 超硬母材 Carbide 超硬母材 Carbide 超硬母材 Carbide ⇒Please use CAD/CAM Support Data Pack for checking interference area. For details, please visit our web site. https://www.moldino.com/ 02 03 壁面削り残り量（mm） Cutting remain amount of wall surface

Page3

新開発した次世代ハードコーティング特長 Features 02 高硬度鋼加工用に刃形を適正化　ダブルフェイス形状 Optimized cutting edge geometry "double-face" for hardened steel machining. TH3コーティングを採用高硬度鋼の加工において図ダブルフェイス形状図ボール刃形断面概略図（A-B断面） Figure : Double Face geometry Figure : A-B cross section view 優れた耐摩耗性を発揮ボール刃逃げ面を2つの面で形成従来刃形 Conventional geometry Flank of ball area has double face (two-stage flank) Applies newly developed next-generation hard coating "TH3 Coating" Excellent wear resistance when machining hardened steel A B 逃げ面 Flank face すくい面 Rake face 先端拡大摩耗の進行方向 2段目逃げ面 Wear progress direction EPDBEH-TH3の特長 2nd flank face Magnified view Features of EPDBEH-TH3 ダブルフェイス形状 Double face geometry 1段目逃げ面 1st flank face 逃げ面 01 高硬度鋼加工用TH3コーティング Flank face すくい面 "TH3 Coating" for hardened steel machining Rake face ダブルフェイス形状で工具摩滅を抑制 1段目逃げ面が摩耗進行を抑制 02 高硬度鋼加工用刃形ダブルフェイス形状 Double-face effect prevents shape from deteriorating First flank face suppresses wear progression Double-face cutting edge geometry for hardened steel machining ※RE2以上はダブルフェイス形状ではありません Double face geometry is not applied to RE2 or larger size 03 高精度加工を追求した工具設計 Tool design to pursue high-accuracy machining 特長 Features 03 高精度加工を追求した工具設計 Tool design to pursue high-accuracy machining RE0.5-首下長10mmの場合バックドラフト形状 Back draft effect 従来首形状対比10% TH3コーティング TH3 Coating 加工のたわみを抑制バックドラフトの効果で良好な加工 EPDBEH-TH3 面品位が得られます。用途（当社計算理論値）炭素鋼ステンレス鋼プリハードン鋼焼入れ鋼焼入れ鋼焼入れ鋼 Applications 合金鋼工具鋼 45～55HRC 55～65HRC 65～72HRC 金型製作部品加工 RE0.05～RE6［ 331 アイテム］バックドラフト形状（強バックテーパ） Carbon steel Stainless steel Pre-hardened Hardened steel Hardened steel Hardened steel Alloy steel Tool steel steel 45̃55HRC 55̃65HRC 65̃72HRC Mold making Parts processing Items In case of R0.5 - under neck length 10mm, を継承。点あたりで切削するので 10% of deflection is suppressed compared to conventional neck ビビりが低減できます。 shape Backdraft effect enables good-quality (Theoretical value by our calculation) processed surfaces to be achieved. 特長 01 高硬度鋼加工用 TH3コーティング Inherits the reliable backdraft shape to enable Features chattering to be reduced by performing point "TH3 Coating " for hardened steel machining cutting. 特長及び性能 Features and performance 皮膜構造 Coating structure ポケット立ち壁仕上げ加工評価結果 Evaluation of cutting remain in pocket wall finishing test ● 優れた耐摩耗性・耐熱性を有する高硬度皮膜優れた耐熱衝撃性を ● 優れた耐衝撃性を有し、突発的な欠損を抑制有する機能皮膜図壁面削り残り量 Figure. Cutting remain amount of wall surface Funcitional layer with excellent 被削材 Work material： YXR33(58HRC) ● 焼入れ鋼など50HRCを超える高硬度鋼の加工領域において長寿命 thermal shock resistance 機　　械 Machine ：立型MC(HSK-E32) Vertical MC ・High hardness coating with excellent wear resistance and heat resistance 0.04 0.0395 優れた耐摩耗性、 0.0369 工　　具 Tool ：EPDBEH2010-6-TH3 ・Has excellent thermal shock resistance enables to suppress sudden chipping 耐熱性を有する新皮膜・Long tool life when cutting high-hardness materials (50HRC or higher) such as hardened steel 切削条件：n=22,600min-1New layer with excellent wear resistance and heat resistance Cutting conditions 0.03 　(vc=71m/min) ターゲットとなる鋼種 Target steel grade ナノ組織を採用 0.0256 　vf=820mm/min Applies nano-size composition 　(fz=0.018mm/t) ● 焼入れ鋼などの高硬度鋼（特に50HRC以上）、ハイス鋼超硬母材 Carbide 0.02 　ap=0.03mm ae=0.01 mm ・Hardened steel (especially 50HRC or higher), high-speed steel 　OH＝18mm　ミスト Mist 13mm 0.01 11mm ! “TH3”のココがポイント！ 5mm 新皮膜は“ナノ組織”の適用により、皮膜の破壊単位を小さくする事に成功！ Point New coating achieves to reduce destruction unit of layer by applying "nano-size composition". ポケットサイズ Pocket size： 0 従来皮膜 13×11×5mm（立ち壁 Wall） Conventional coating 大きく破壊新皮膜 New coating EPDBEH-TH3 従来品1 従来品2 Conventional 1 Conventional 2 Big destruction 切削抵抗切削抵抗小さく破壊 Small destruction 首部の剛性を高めることでたわみを抑制でき、従来比30%の削り残り量削減 Cutting force Cutting force By increasing the neck rigidity, it is possible to suppress deflection and reduce the cutting remain by 30% than conventional design 従来のエポックディープエボリューションシリーズ（EPDBEHやEPDBE）と比較すると実有効首下長が短くなっております。干渉領域をチェックした上でご使用お願いします。 Effective neck length is shorter than existing Epoch Deep Evolution series (EPDBEH, EPDBE). Please use with checking interference area. ⇒ 干渉チェックはCAD/CAMサポートデータパックをご使用ください。詳細は弊社ホームページをご覧ください超硬母材 Carbide 超硬母材 Carbide 超硬母材 Carbide 超硬母材 Carbide ⇒Please use CAD/CAM Support Data Pack for checking interference area. For details, please visit our web site. https://www.moldino.com/ 02 03 壁面削り残り量（mm） Cutting remain amount of wall surface

Page4

バリエーション Var iat ion 最短首下長　ストロングネックタイプショートシャンクタイプ Shortest neck length, Strong neck type Short shank type EPDBEH2◌◌◌F-◌◌-TH3 従来よりも太く短い首形状 Thicker and shorter neck shape than conventional lineup ストロングネック従来品 Strong neck Conventional 各種精密金型の加工にお役立てください待望のショートシャンクタイプが Please utilize for machining various precision molds and dies 仲間入り! Range now includes the short shank type! 【 RE0.05～RE1.25 100アイテム items 】 Semiconductor Light Guide Connector Engraving 半導体部品ライトガイドコネクター文字彫り Regular Short レギュラーシャンクショートシャンクさらなる高精度・安定加工の実現に向けて剛性にこだわった最短首下長をラインナップに追加！焼きばめホルダにFitする全長設計 Lineup expanded with shortest under-neck length range that emphasizes rigidity Full-length design that fits shrink-fit holders in order to realize higher precision and stable machining 外径実測値ラベル表記をスタート【 RE1.25以下の全サイズ対象】小径エンドミルは折損のリスクがあるため Now featuring labeling of actual tool diameter (for all sizes up to RE1.25) 首下長がもっと短い工具を使いたい Actual size indicated here. Needs to use tools with shorter neck length since small diameter end mills have a risk of breakage ここに実測値が表記されます。測定の手間なく実測値をCAMに反映し DC= 最短首下長のストロングネックタイプ 0.000 EPDBEH2001F-0.2-TH3 加工精度の向上に貢献 !! RO.O5XO.2 TH3 Coat Strong neck type with the shortest neck length MADE IN JAPAN Allows use of actual size in CAM ※商品ラベルイメージ without the need for measurement, 高い工具剛性により安定性・信頼性が向上します Example product label for improved machining accuracy! 特に工具径が小さくなるほど効果的です High tool rigidity improves stability and reliability. Especially, it is more effective as the tool diameter becomes smaller. ショートシャンクタイプから適用いたします。 For initial introduction on short shank type products 04 05 INSPECTED

Page5

バリエーション Var iat ion 最短首下長　ストロングネックタイプショートシャンクタイプ Shortest neck length, Strong neck type Short shank type EPDBEH2◌◌◌F-◌◌-TH3 従来よりも太く短い首形状 Thicker and shorter neck shape than conventional lineup ストロングネック従来品 Strong neck Conventional 各種精密金型の加工にお役立てください待望のショートシャンクタイプが Please utilize for machining various precision molds and dies 仲間入り! Range now includes the short shank type! 【 RE0.05～RE1.25 100アイテム items 】 Semiconductor Light Guide Connector Engraving 半導体部品ライトガイドコネクター文字彫り Regular Short レギュラーシャンクショートシャンクさらなる高精度・安定加工の実現に向けて剛性にこだわった最短首下長をラインナップに追加！焼きばめホルダにFitする全長設計 Lineup expanded with shortest under-neck length range that emphasizes rigidity Full-length design that fits shrink-fit holders in order to realize higher precision and stable machining 外径実測値ラベル表記をスタート【 RE1.25以下の全サイズ対象】小径エンドミルは折損のリスクがあるため Now featuring labeling of actual tool diameter (for all sizes up to RE1.25) 首下長がもっと短い工具を使いたい Actual size indicated here. Needs to use tools with shorter neck length since small diameter end mills have a risk of breakage ここに実測値が表記されます。測定の手間なく実測値をCAMに反映し DC= 最短首下長のストロングネックタイプ 0.000 EPDBEH2001F-0.2-TH3 加工精度の向上に貢献 !! RO.O5XO.2 TH3 Coat Strong neck type with the shortest neck length MADE IN JAPAN Allows use of actual size in CAM ※商品ラベルイメージ without the need for measurement, 高い工具剛性により安定性・信頼性が向上します Example product label for improved machining accuracy! 特に工具径が小さくなるほど効果的です High tool rigidity improves stability and reliability. Especially, it is more effective as the tool diameter becomes smaller. ショートシャンクタイプから適用いたします。 For initial introduction on short shank type products 04 05 INSPECTED

Page6

ラインナップ Line Up ショートシャンクタイプ Short shank type RE RE 外周バックテーパ：2.5°～8.5° APMX 15° 15° Back taper on peripheral edge LU 2枚刃 LF LF LU・APMX 2 Flutes 外周バックテーパ：2.5°～8.5° LB2 Aタイプ Back taper on peripheral edge A type （㎜） Bタイプ B type Bタイプの詳細はP.13をご確認ください For details of B type, refer to page 13. ボール半径RE RE公差 Ball radius Tolerance on RE EPDBEH2 F- . -TH3 ねじれ30° 超硬 0.05～0.25 ±0.003 Carbide Helix angle 0.3～1.25 ±0.005 EPDBEH2 F- . -TH3 寸　法　Size(mm) 干渉角度勾配角に対する実有効首下長希望小売寸　法　Size(mm) 干渉角度勾配角に対する実有効首下長希望小売商品コード在庫ボール半径外径首下長刃長首径全長シャンク径タイプ Interference angle Effective under neck length 価格（円）商品コード在庫ボール半径外径首下長刃長首径全長シャンク径タイプ Interference angle Effective under neck length 価格（円） Item code Stock Ball radius Tool dia. Under neck length Flute length Neck dia. Overall length Shank dia. Type （°） with respect to draft angle Suggested a. Under neck length Flute length Neck dia. Overall length Shank dia. retail price Item code Type （°） with respect to draft angle Stock Ball radius Tool di Suggested retail price RE DC LU APMX DN LF DCONMS θκ 0.5° 1° 1.5° 2° 3° (￥) RE DC LU APMX DN LF DCONMS θκ 0.5° 1° 1.5° 2° 3° (￥) EPDBEH2001F-0.08-TH3 ★ 0.08 － B 20.93 －－－－－ 17,920 EPDBEH2008F-0.5-TH3 ★ 0.5 － B 14.20 －－－－－ 6,600 EPDBEH2001F-0.2-TH3 ★ 0.2 A 14.64 0.24 0.25 0.25 0.26 0.28 17,920 EPDBEH2008F-1-TH3 ★ 1 35 A 13.58 1.07 1.10 1.12 1.15 1.21 6,600 ★ 0.05 0.1 0.08 35 4 EPDBEH2001F-0.3-TH3 0.3 0.08 A 14.46 0.34 0.35 0.36 0.38 0.40 18,400 EPDBEH2008F-1.5-TH3 ★ 1.5 A 12.66 1.59 1.63 1.68 1.73 1.83 6,600 EPDBEH2001F-0.5-TH3 ★ 0.5 A 14.10 0.55 0.57 0.59 0.61 0.65 19,930 EPDBEH2008F-2-TH3 ★ 2 A 11.85 2.11 2.17 2.23 2.30 2.46 6,600 EPDBEH20015F-0.12-TH3 ★ 0.12 － B 15.25 －－－－－ 18,400 EPDBEH2008F-2.5-TH3 ★ 2.5 A 11.14 2.62 2.70 2.79 2.88 3.08 6,850 38 4 EPDBEH20015F-0.3-TH3 ★ 0.3 A 14.50 0.34 0.35 0.36 0.37 0.40 18,400 ★ 0.4 0.8 0.5 EPDBEH2008F-3-TH3 3 0.77 A 10.51 3.14 3.24 3.34 3.45 3.70 7,060 ★ 0.075 0.15 0.12 35 4 EPDBEH20015F-0.5-TH3 0.5 0.13 A 14.14 0.55 0.56 0.58 0.60 0.65 19,930 EPDBEH2008F-4-TH3 ★ 4 A 9.44 4.17 4.31 4.45 4.60 4.94 7,060 EPDBEH20015F-0.75-TH3 ★ 0.75 A 13.71 0.81 0.83 0.86 0.89 0.96 21,690 EPDBEH2008F-5-TH3 ★ 5 A 8.57 5.21 5.38 5.56 5.75 6.19 7,060 EPDBEH2002F-0.15-TH3 ★ 0.15 － B 20.23 －－－－－ 12,850 EPDBEH2008F-6-TH3 ★ 6 42 A 7.84 6.24 6.45 6.66 6.90 7.43 7,060 EPDBEH2002F-0.3-TH3 ★ 0.3 A 14.54 0.34 0.35 0.36 0.37 0.39 12,850 EPDBEH2008F-8-TH3 ★ 8 A 6.70 8.31 8.58 8.88 9.20 9.92 7,060 ★ 35 EPDBEH2002F-0.5-TH3 0.1 0.2 0.5 0.15 4 A 14.17 0.55 0.56 0.58 0.60 0.64 12,850 EPDBEH2009F-0.6-TH3 ★ 0.6 － B 13.84 －－－－－ 6,600 ★ 0.18 35 EPDBEH2002F-0.75-TH3 0.75 A 13.73 0.81 0.83 0.86 0.89 0.95 12,850 EPDBEH2009F-2-TH3 ★ 2 A 11.85 2.11 2.16 2.23 2.29 2.44 6,600 4 EPDBEH2002F-1-TH3 ★ 1 38 A 13.32 1.06 1.10 1.13 1.17 1.26 12,850 ★ 0.45 0.9 0.6 EPDBEH2009F-4-TH3 4 0.87 38 A 9.38 4.17 4.30 4.44 4.59 4.93 7,060 EPDBEH2003F-0.25-TH3 ★ 0.25 － B 14.45 －－－－－ 12,620 EPDBEH2009F-6-TH3 ★ 6 42 A 7.75 6.24 6.44 6.66 6.89 7.42 7,060 EPDBEH2003F-0.5-TH3 ★ 0.5 A 14.21 0.56 0.58 0.60 0.61 0.65 12,620 EPDBEH2010F-0.8-TH3 ★ 0.8 － B 13.47 －－－－－ 5,530 ★ 35 EPDBEH2003F-0.75-TH3 0.15 0.3 0.75 0.25 4 A 13.76 0.82 0.85 0.87 0.90 0.96 12,620 EPDBEH2010F-1.5-TH3 ★ 1.5 35 A 12.67 1.61 1.64 1.69 1.73 1.83 5,530 ★ 0.27 EPDBEH2003F-1-TH3 1 A 13.33 1.08 1.11 1.15 1.19 1.27 12,620 EPDBEH2010F-2-TH3 ★ 2 A 11.82 2.12 2.18 2.24 2.31 2.46 5,530 EPDBEH2003F-1.5-TH3 ★ 1.5 38 A 12.56 1.60 1.65 1.70 1.76 1.89 13,450 EPDBEH2010F-2.5-TH3 ★ 2.5 A 11.07 2.64 2.71 2.80 2.88 3.08 5,530 EPDBEH2004F-0.3-TH3 ★ 0.3 － B 14.53 －－－－－ 8,600 EPDBEH2010F-3-TH3 ★ 3 A 10.41 3.16 3.25 3.35 3.46 3.70 5,530 38 EPDBEH2004F-0.5-TH3 ★ 0.5 A 14.28 0.56 0.58 0.59 0.60 0.64 8,600 EPDBEH2010F-4-TH3 ★ 4 A 9.29 4.19 4.32 4.46 4.61 4.94 6,300 ★ 35 4 EPDBEH2004F-0.75-TH3 0.75 A 13.81 0.82 0.84 0.87 0.89 0.95 8,600 ★ 0.5 1 0.8 EPDBEH2010F-5-TH3 5 0.96 A 8.39 5.22 5.39 5.57 5.76 6.19 6,300 EPDBEH2004F-1-TH3 ★ 1 A 13.37 1.08 1.11 1.14 1.18 1.26 8,600 EPDBEH2010F-6-TH3 ★ 6 A 7.65 6.26 6.46 6.67 6.91 7.43 6,760 EPDBEH2004F-1.5-TH3 ★ 0.2 0.4 1.5 0.3 4 A 12.57 1.60 1.65 1.70 1.75 1.88 8,740 EPDBEH2010F-7-TH3 ★ 7 42 A 7.03 7.29 7.53 7.78 8.06 8.67 6,760 ★ 0.37 EPDBEH2004F-2-TH3 2 A 11.86 2.11 2.18 2.25 2.33 2.50 9,060 EPDBEH2010F-8-TH3 ★ 8 A 6.50 8.32 8.60 8.89 9.21 9.91 6,760 EPDBEH2004F-2.5-TH3 ★ 2.5 38 A 11.23 2.63 2.72 2.81 2.90 3.13 9,350 EPDBEH2010F-10-TH3 ★ 10 A 5.65 10.39 10.74 11.11 11.51 12.40 6,760 45 EPDBEH2004F-3-TH3 ★ 3 A 10.65 3.15 3.25 3.36 3.48 3.75 9,970 EPDBEH2010F-12-TH3 ★ 12 A 5.00 12.46 12.88 13.32 13.81 14.89 6,760 EPDBEH2004F-4-TH3 ★ 4 A 9.67 4.18 4.32 4.47 4.63 4.99 10,740 EPDBEH2015F-2-TH3 ★ 2 A 11.76 2.13 2.18 2.23 2.29 2.42 6,440 EPDBEH2005F-0.35-TH3 ★ 0.35 － B 14.10 －－－－－ 8,600 EPDBEH2015F-2.5-TH3 ★ 2.5 35 A 10.88 2.65 2.72 2.79 2.87 3.04 6,440 EPDBEH2005F-0.75-TH3 ★ 0.75 35 A 13.88 0.82 0.84 0.86 0.88 0.94 8,600 EPDBEH2015F-3-TH3 ★ 3 A 10.12 3.17 3.25 3.34 3.44 3.66 6,440 EPDBEH2005F-1-TH3 ★ 1 A 13.42 1.08 1.11 1.14 1.17 1.25 8,600 EPDBEH2015F-4-TH3 ★ 4 A 8.88 4.20 4.32 4.45 4.59 4.91 6,440 EPDBEH2005F-1.5-TH3 ★ 1.5 A 12.59 1.59 1.64 1.69 1.75 1.87 8,600 EPDBEH2015F-5-TH3 ★ 0.75 1.5 5 1.35 1.45 38 4 A 7.90 5.23 5.39 5.56 5.74 6.15 6,440 EPDBEH2005F-2-TH3 ★ 0.25 0.5 2 0.35 4 A 11.86 2.11 2.18 2.25 2.32 2.49 8,600 EPDBEH2015F-6-TH3 ★ 6 A 7.12 6.27 6.46 6.67 6.89 7.39 6,440 ★ 0.47 EPDBEH2005F-2.5-TH3 2.5 38 A 11.21 2.63 2.71 2.80 2.90 3.11 8,600 EPDBEH2015F-8-TH3 ★ 8 A 5.95 8.34 8.60 8.88 9.19 9.88 6,760 42 EPDBEH2005F-3-TH3 ★ 3 A 10.62 3.15 3.25 3.36 3.47 3.73 8,600 EPDBEH2015F-10-TH3 ★ 10 A 5.10 10.40 10.74 11.10 11.49 12.36 7,360 EPDBEH2005F-4-TH3 ★ 4 A 9.61 4.18 4.32 4.46 4.62 4.98 8,600 EPDBEH2015F-12-TH3 ★ 12 45 A 4.47 12.47 12.88 13.32 13.79 14.85 7,980 EPDBEH2005F-5-TH3 ★ 5 42 A 8.78 5.21 5.39 5.57 5.77 6.22 8,740 EPDBEH2020F-2.5-TH3 ★ 2.5 A 10.60 2.66 2.72 2.78 2.85 3.01 5,530 EPDBEH2006F-0.4-TH3 ★ 0.4 － B 14.16 －－－－－ 7,420 EPDBEH2020F-3-TH3 ★ 3 35 A 9.72 3.18 3.25 3.34 3.43 3.63 5,530 EPDBEH2006F-0.75-TH3 ★ 0.75 A 13.94 0.82 0.84 0.86 0.88 0.93 7,420 EPDBEH2020F-4-TH3 ★ 4 A 8.32 4.21 4.32 4.45 4.58 4.87 5,530 ★ 35 EPDBEH2006F-1-TH3 1 A 13.47 1.08 1.10 1.13 1.17 1.24 7,420 EPDBEH2020F-5-TH3 ★ 5 A 7.27 5.25 5.39 5.55 5.73 6.11 6,300 38 EPDBEH2006F-1.5-TH3 ★ 1.5 A 12.61 1.59 1.64 1.69 1.74 1.86 6,600 EPDBEH2020F-6-TH3 ★ 6 A 6.46 6.28 6.46 6.66 6.88 7.36 6,300 EPDBEH2006F-2-TH3 ★ 2 A 11.86 2.11 2.17 2.24 2.31 2.48 6,600 EPDBEH2020F-8-TH3 ★ 8 A 5.27 8.35 8.60 8.88 9.18 9.84 6,760 1.94 42 4 EPDBEH2006F-2.5-TH3 ★ 0.3 0.6 2.5 0.4 4 A 11.19 2.63 2.71 2.80 2.89 3.10 6,760 ★ 1 2 1.7 EPDBEH2020F-10-TH3 10 A 4.46 10.41 10.74 11.10 11.48 12.33 6,760 0.57 EPDBEH2006F-3-TH3 ★ 3 38 A 10.59 3.14 3.24 3.35 3.46 3.72 6,760 EPDBEH2020F-12-TH3 ★ 12 A 3.86 12.48 12.88 13.31 13.77 14.82 6,760 EPDBEH2006F-3.5-TH3 ★ 3.5 A 10.05 3.66 3.78 3.90 4.04 4.34 7,060 EPDBEH2020F-13-TH3 ★ 13 45 A 3.62 13.51 13.95 14.42 14.92 16.06 6,760 EPDBEH2006F-4-TH3 ★ 4 A 9.56 4.18 4.31 4.46 4.61 4.97 7,060 EPDBEH2020F-14-TH3 ★ 14 A 3.40 14.55 15.02 15.53 16.07 17.30 6,760 EPDBEH2006F-5-TH3 ★ 5 A 8.71 5.21 5.38 5.57 5.76 6.21 7,060 EPDBEH2020F-16-TH3 ★ 16 50 A 3.04 16.62 17.16 17.75 18.37 19.79 6,760 42 EPDBEH2006F-6-TH3 ★ 6 A 8.00 6.24 6.45 6.67 6.91 7.45 7,060 EPDBEH2020F-20-TH3 ★ 20 55 A 2.51 20.75 21.44 22.18 22.97 干渉なし 6,760 EPDBEH2007F-0.45-TH3 ★ 0.45 － 35 B 14.13 －－－－－ 6,600 EPDBEH2025F-6-TH3 ★ 6 38 A 5.54 6.35 6.53 6.72 6.92 7.39 8,500 EPDBEH2007F-2-TH3 ★ 0.35 0.7 2 0.45 4 A 11.85 2.11 2.17 2.24 2.31 2.47 6,600 EPDBEH2025F-10-TH3 ★ 1.25 2.5 10 2 2.4 42 4 A 3.66 10.48 10.81 11.15 11.52 12.36 9,060 0.67 38 EPDBEH2007F-4-TH3 ★ 4 A 9.50 4.18 4.31 4.45 4.61 4.95 7,060 EPDBEH2025F-15-TH3 ★ 15 45 A 2.57 15.65 16.15 16.69 17.27 干渉なし 9,220 ★：新商品の標準在庫品です。★：Stocked items of new products.　 06 07 DC DN DCONMS DC BD2 DCONMS

Page7

ラインナップ Line Up ショートシャンクタイプ Short shank type RE RE 外周バックテーパ：2.5°～8.5° APMX 15° 15° Back taper on peripheral edge LU 2枚刃 LF LF LU・APMX 2 Flutes 外周バックテーパ：2.5°～8.5° LB2 Aタイプ Back taper on peripheral edge A type （㎜） Bタイプ B type Bタイプの詳細はP.13をご確認ください For details of B type, refer to page 13. ボール半径RE RE公差 Ball radius Tolerance on RE EPDBEH2 F- . -TH3 ねじれ30° 超硬 0.05～0.25 ±0.003 Carbide Helix angle 0.3～1.25 ±0.005 EPDBEH2 F- . -TH3 寸　法　Size(mm) 干渉角度勾配角に対する実有効首下長希望小売寸　法　Size(mm) 干渉角度勾配角に対する実有効首下長希望小売商品コード在庫ボール半径外径首下長刃長首径全長シャンク径タイプ Interference angle Effective under neck length 価格（円）商品コード在庫ボール半径外径首下長刃長首径全長シャンク径タイプ Interference angle Effective under neck length 価格（円） Item code Stock Ball radius Tool dia. Under neck length Flute length Neck dia. Overall length Shank dia. Type （°） with respect to draft angle Suggested a. Under neck length Flute length Neck dia. Overall length Shank dia. retail price Item code Type （°） with respect to draft angle Stock Ball radius Tool di Suggested retail price RE DC LU APMX DN LF DCONMS θκ 0.5° 1° 1.5° 2° 3° (￥) RE DC LU APMX DN LF DCONMS θκ 0.5° 1° 1.5° 2° 3° (￥) EPDBEH2001F-0.08-TH3 ★ 0.08 － B 20.93 －－－－－ 17,920 EPDBEH2008F-0.5-TH3 ★ 0.5 － B 14.20 －－－－－ 6,600 EPDBEH2001F-0.2-TH3 ★ 0.2 A 14.64 0.24 0.25 0.25 0.26 0.28 17,920 EPDBEH2008F-1-TH3 ★ 1 35 A 13.58 1.07 1.10 1.12 1.15 1.21 6,600 ★ 0.05 0.1 0.08 35 4 EPDBEH2001F-0.3-TH3 0.3 0.08 A 14.46 0.34 0.35 0.36 0.38 0.40 18,400 EPDBEH2008F-1.5-TH3 ★ 1.5 A 12.66 1.59 1.63 1.68 1.73 1.83 6,600 EPDBEH2001F-0.5-TH3 ★ 0.5 A 14.10 0.55 0.57 0.59 0.61 0.65 19,930 EPDBEH2008F-2-TH3 ★ 2 A 11.85 2.11 2.17 2.23 2.30 2.46 6,600 EPDBEH20015F-0.12-TH3 ★ 0.12 － B 15.25 －－－－－ 18,400 EPDBEH2008F-2.5-TH3 ★ 2.5 A 11.14 2.62 2.70 2.79 2.88 3.08 6,850 38 4 EPDBEH20015F-0.3-TH3 ★ 0.3 A 14.50 0.34 0.35 0.36 0.37 0.40 18,400 ★ 0.4 0.8 0.5 EPDBEH2008F-3-TH3 3 0.77 A 10.51 3.14 3.24 3.34 3.45 3.70 7,060 ★ 0.075 0.15 0.12 35 4 EPDBEH20015F-0.5-TH3 0.5 0.13 A 14.14 0.55 0.56 0.58 0.60 0.65 19,930 EPDBEH2008F-4-TH3 ★ 4 A 9.44 4.17 4.31 4.45 4.60 4.94 7,060 EPDBEH20015F-0.75-TH3 ★ 0.75 A 13.71 0.81 0.83 0.86 0.89 0.96 21,690 EPDBEH2008F-5-TH3 ★ 5 A 8.57 5.21 5.38 5.56 5.75 6.19 7,060 EPDBEH2002F-0.15-TH3 ★ 0.15 － B 20.23 －－－－－ 12,850 EPDBEH2008F-6-TH3 ★ 6 42 A 7.84 6.24 6.45 6.66 6.90 7.43 7,060 EPDBEH2002F-0.3-TH3 ★ 0.3 A 14.54 0.34 0.35 0.36 0.37 0.39 12,850 EPDBEH2008F-8-TH3 ★ 8 A 6.70 8.31 8.58 8.88 9.20 9.92 7,060 ★ 35 EPDBEH2002F-0.5-TH3 0.1 0.2 0.5 0.15 4 A 14.17 0.55 0.56 0.58 0.60 0.64 12,850 EPDBEH2009F-0.6-TH3 ★ 0.6 － B 13.84 －－－－－ 6,600 ★ 0.18 35 EPDBEH2002F-0.75-TH3 0.75 A 13.73 0.81 0.83 0.86 0.89 0.95 12,850 EPDBEH2009F-2-TH3 ★ 2 A 11.85 2.11 2.16 2.23 2.29 2.44 6,600 4 EPDBEH2002F-1-TH3 ★ 1 38 A 13.32 1.06 1.10 1.13 1.17 1.26 12,850 ★ 0.45 0.9 0.6 EPDBEH2009F-4-TH3 4 0.87 38 A 9.38 4.17 4.30 4.44 4.59 4.93 7,060 EPDBEH2003F-0.25-TH3 ★ 0.25 － B 14.45 －－－－－ 12,620 EPDBEH2009F-6-TH3 ★ 6 42 A 7.75 6.24 6.44 6.66 6.89 7.42 7,060 EPDBEH2003F-0.5-TH3 ★ 0.5 A 14.21 0.56 0.58 0.60 0.61 0.65 12,620 EPDBEH2010F-0.8-TH3 ★ 0.8 － B 13.47 －－－－－ 5,530 ★ 35 EPDBEH2003F-0.75-TH3 0.15 0.3 0.75 0.25 4 A 13.76 0.82 0.85 0.87 0.90 0.96 12,620 EPDBEH2010F-1.5-TH3 ★ 1.5 35 A 12.67 1.61 1.64 1.69 1.73 1.83 5,530 ★ 0.27 EPDBEH2003F-1-TH3 1 A 13.33 1.08 1.11 1.15 1.19 1.27 12,620 EPDBEH2010F-2-TH3 ★ 2 A 11.82 2.12 2.18 2.24 2.31 2.46 5,530 EPDBEH2003F-1.5-TH3 ★ 1.5 38 A 12.56 1.60 1.65 1.70 1.76 1.89 13,450 EPDBEH2010F-2.5-TH3 ★ 2.5 A 11.07 2.64 2.71 2.80 2.88 3.08 5,530 EPDBEH2004F-0.3-TH3 ★ 0.3 － B 14.53 －－－－－ 8,600 EPDBEH2010F-3-TH3 ★ 3 A 10.41 3.16 3.25 3.35 3.46 3.70 5,530 38 EPDBEH2004F-0.5-TH3 ★ 0.5 A 14.28 0.56 0.58 0.59 0.60 0.64 8,600 EPDBEH2010F-4-TH3 ★ 4 A 9.29 4.19 4.32 4.46 4.61 4.94 6,300 ★ 35 4 EPDBEH2004F-0.75-TH3 0.75 A 13.81 0.82 0.84 0.87 0.89 0.95 8,600 ★ 0.5 1 0.8 EPDBEH2010F-5-TH3 5 0.96 A 8.39 5.22 5.39 5.57 5.76 6.19 6,300 EPDBEH2004F-1-TH3 ★ 1 A 13.37 1.08 1.11 1.14 1.18 1.26 8,600 EPDBEH2010F-6-TH3 ★ 6 A 7.65 6.26 6.46 6.67 6.91 7.43 6,760 EPDBEH2004F-1.5-TH3 ★ 0.2 0.4 1.5 0.3 4 A 12.57 1.60 1.65 1.70 1.75 1.88 8,740 EPDBEH2010F-7-TH3 ★ 7 42 A 7.03 7.29 7.53 7.78 8.06 8.67 6,760 ★ 0.37 EPDBEH2004F-2-TH3 2 A 11.86 2.11 2.18 2.25 2.33 2.50 9,060 EPDBEH2010F-8-TH3 ★ 8 A 6.50 8.32 8.60 8.89 9.21 9.91 6,760 EPDBEH2004F-2.5-TH3 ★ 2.5 38 A 11.23 2.63 2.72 2.81 2.90 3.13 9,350 EPDBEH2010F-10-TH3 ★ 10 A 5.65 10.39 10.74 11.11 11.51 12.40 6,760 45 EPDBEH2004F-3-TH3 ★ 3 A 10.65 3.15 3.25 3.36 3.48 3.75 9,970 EPDBEH2010F-12-TH3 ★ 12 A 5.00 12.46 12.88 13.32 13.81 14.89 6,760 EPDBEH2004F-4-TH3 ★ 4 A 9.67 4.18 4.32 4.47 4.63 4.99 10,740 EPDBEH2015F-2-TH3 ★ 2 A 11.76 2.13 2.18 2.23 2.29 2.42 6,440 EPDBEH2005F-0.35-TH3 ★ 0.35 － B 14.10 －－－－－ 8,600 EPDBEH2015F-2.5-TH3 ★ 2.5 35 A 10.88 2.65 2.72 2.79 2.87 3.04 6,440 EPDBEH2005F-0.75-TH3 ★ 0.75 35 A 13.88 0.82 0.84 0.86 0.88 0.94 8,600 EPDBEH2015F-3-TH3 ★ 3 A 10.12 3.17 3.25 3.34 3.44 3.66 6,440 EPDBEH2005F-1-TH3 ★ 1 A 13.42 1.08 1.11 1.14 1.17 1.25 8,600 EPDBEH2015F-4-TH3 ★ 4 A 8.88 4.20 4.32 4.45 4.59 4.91 6,440 EPDBEH2005F-1.5-TH3 ★ 1.5 A 12.59 1.59 1.64 1.69 1.75 1.87 8,600 EPDBEH2015F-5-TH3 ★ 0.75 1.5 5 1.35 1.45 38 4 A 7.90 5.23 5.39 5.56 5.74 6.15 6,440 EPDBEH2005F-2-TH3 ★ 0.25 0.5 2 0.35 4 A 11.86 2.11 2.18 2.25 2.32 2.49 8,600 EPDBEH2015F-6-TH3 ★ 6 A 7.12 6.27 6.46 6.67 6.89 7.39 6,440 ★ 0.47 EPDBEH2005F-2.5-TH3 2.5 38 A 11.21 2.63 2.71 2.80 2.90 3.11 8,600 EPDBEH2015F-8-TH3 ★ 8 A 5.95 8.34 8.60 8.88 9.19 9.88 6,760 42 EPDBEH2005F-3-TH3 ★ 3 A 10.62 3.15 3.25 3.36 3.47 3.73 8,600 EPDBEH2015F-10-TH3 ★ 10 A 5.10 10.40 10.74 11.10 11.49 12.36 7,360 EPDBEH2005F-4-TH3 ★ 4 A 9.61 4.18 4.32 4.46 4.62 4.98 8,600 EPDBEH2015F-12-TH3 ★ 12 45 A 4.47 12.47 12.88 13.32 13.79 14.85 7,980 EPDBEH2005F-5-TH3 ★ 5 42 A 8.78 5.21 5.39 5.57 5.77 6.22 8,740 EPDBEH2020F-2.5-TH3 ★ 2.5 A 10.60 2.66 2.72 2.78 2.85 3.01 5,530 EPDBEH2006F-0.4-TH3 ★ 0.4 － B 14.16 －－－－－ 7,420 EPDBEH2020F-3-TH3 ★ 3 35 A 9.72 3.18 3.25 3.34 3.43 3.63 5,530 EPDBEH2006F-0.75-TH3 ★ 0.75 A 13.94 0.82 0.84 0.86 0.88 0.93 7,420 EPDBEH2020F-4-TH3 ★ 4 A 8.32 4.21 4.32 4.45 4.58 4.87 5,530 ★ 35 EPDBEH2006F-1-TH3 1 A 13.47 1.08 1.10 1.13 1.17 1.24 7,420 EPDBEH2020F-5-TH3 ★ 5 A 7.27 5.25 5.39 5.55 5.73 6.11 6,300 38 EPDBEH2006F-1.5-TH3 ★ 1.5 A 12.61 1.59 1.64 1.69 1.74 1.86 6,600 EPDBEH2020F-6-TH3 ★ 6 A 6.46 6.28 6.46 6.66 6.88 7.36 6,300 EPDBEH2006F-2-TH3 ★ 2 A 11.86 2.11 2.17 2.24 2.31 2.48 6,600 EPDBEH2020F-8-TH3 ★ 8 A 5.27 8.35 8.60 8.88 9.18 9.84 6,760 1.94 42 4 EPDBEH2006F-2.5-TH3 ★ 0.3 0.6 2.5 0.4 4 A 11.19 2.63 2.71 2.80 2.89 3.10 6,760 ★ 1 2 1.7 EPDBEH2020F-10-TH3 10 A 4.46 10.41 10.74 11.10 11.48 12.33 6,760 0.57 EPDBEH2006F-3-TH3 ★ 3 38 A 10.59 3.14 3.24 3.35 3.46 3.72 6,760 EPDBEH2020F-12-TH3 ★ 12 A 3.86 12.48 12.88 13.31 13.77 14.82 6,760 EPDBEH2006F-3.5-TH3 ★ 3.5 A 10.05 3.66 3.78 3.90 4.04 4.34 7,060 EPDBEH2020F-13-TH3 ★ 13 45 A 3.62 13.51 13.95 14.42 14.92 16.06 6,760 EPDBEH2006F-4-TH3 ★ 4 A 9.56 4.18 4.31 4.46 4.61 4.97 7,060 EPDBEH2020F-14-TH3 ★ 14 A 3.40 14.55 15.02 15.53 16.07 17.30 6,760 EPDBEH2006F-5-TH3 ★ 5 A 8.71 5.21 5.38 5.57 5.76 6.21 7,060 EPDBEH2020F-16-TH3 ★ 16 50 A 3.04 16.62 17.16 17.75 18.37 19.79 6,760 42 EPDBEH2006F-6-TH3 ★ 6 A 8.00 6.24 6.45 6.67 6.91 7.45 7,060 EPDBEH2020F-20-TH3 ★ 20 55 A 2.51 20.75 21.44 22.18 22.97 干渉なし 6,760 EPDBEH2007F-0.45-TH3 ★ 0.45 － 35 B 14.13 －－－－－ 6,600 EPDBEH2025F-6-TH3 ★ 6 38 A 5.54 6.35 6.53 6.72 6.92 7.39 8,500 EPDBEH2007F-2-TH3 ★ 0.35 0.7 2 0.45 4 A 11.85 2.11 2.17 2.24 2.31 2.47 6,600 EPDBEH2025F-10-TH3 ★ 1.25 2.5 10 2 2.4 42 4 A 3.66 10.48 10.81 11.15 11.52 12.36 9,060 0.67 38 EPDBEH2007F-4-TH3 ★ 4 A 9.50 4.18 4.31 4.45 4.61 4.95 7,060 EPDBEH2025F-15-TH3 ★ 15 45 A 2.57 15.65 16.15 16.69 17.27 干渉なし 9,220 ★：新商品の標準在庫品です。★：Stocked items of new products.　 06 07 DC DN DCONMS DC BD2 DCONMS

Page8

ラインナップ Line Up レギュラーシャンクタイプ Regular shank type RE RE 2枚刃外周バックテーパ：2.5°～8.5° APMX 15° 15° 2 Flutes Back taper on peripheral edge LU LF LF LU・APMX 外周バックテーパ：2.5°～8.5° LB2 【注意】RE 2mm以上はバックドラフト形状ではありません。【Note】RE 2mm or larger does not have backdraft shape. Aタイプ Back taper on peripheral edge A type （㎜） Bタイプ B type Bタイプの詳細はP.13をご確認ください For details of B type, refer to page 13. ボール半径RE RE公差 Ball radius Tolerance on RE EPDBEH2 - . -(S6)-TH3 ねじれ30° 超硬 0.05～0.25 ±0.003 Carbide Helix angle 0.3～6 ±0.005 EPDBEH2 - . -(S6)-TH3 φ4 φ6～φ12 寸　法　Size(mm) 干渉角度勾配角に対する実有効首下長希望小売寸　法　Size(mm) 干渉角度勾配角に対する実有効首下長希望小売商品コード在庫ボール半径外径首下長刃長首径全長シャンク径タイプ Interference angle Effective under neck length 価格（円）商品コード在庫ボール半径外径首下長刃長首径全長シャンク径タイプ Interference angle Effective under neck length 価格（円） Item code Ball radius Tool dia. Under neck length Flute length Neck dia. Overall length Shank dia. Type （°） with respect to draft angle Stock Suggested retail price Item code with respect to draft angle Stock Ball radius Tool dia. Under neck length Flute length Neck dia. Overall length Shank dia. Type （°） Suggested retail price RE DC LU APMX DN LF DCONMS θκ 0.5° 1° 1.5° 2° 3° (￥) RE DC LU APMX DN LF DCONMS θκ 0.5° 1° 1.5° 2° 3° (￥) EPDBEH2001-0.08-TH3 ● 0.08 － B 20.93 －－－－－ 17,920 EPDBEH2005-2.5-TH3 ● 2.5 A 11.21 2.63 2.71 2.80 2.90 3.11 8,600 EPDBEH2001-0.2-TH3 ● 0.2 A 14.64 0.24 0.25 0.25 0.26 0.28 17,920 EPDBEH2005-3-TH3 ● 3 A 10.62 3.15 3.25 3.36 3.47 3.73 8,600 0.05 0.1 0.08 0.08 45 4 EPDBEH2001-0.3-TH3 ● 0.3 A 14.46 0.34 0.35 0.36 0.38 0.40 18,400 EPDBEH2005-4-TH3 ● 4 A 9.61 4.18 4.32 4.46 4.62 4.98 8,600 EPDBEH2001-0.5-TH3 ● 0.5 A 14.10 0.55 0.57 0.59 0.61 0.65 19,930 EPDBEH2005-5-TH3 ● 5 A 8.78 5.21 5.39 5.57 5.77 6.22 8,740 0.25 0.5 0.35 0.47 50 4 EPDBEH20015-0.12-TH3 ● 0.12 － B 15.25 －－－－－ 18,400 EPDBEH2005-5.5-TH3 ● 5.5 A 8.41 5.73 5.92 6.13 6.35 6.84 9,060 EPDBEH20015-0.3-TH3 ● 0.3 A 14.50 0.34 0.35 0.36 0.37 0.40 18,400 EPDBEH2005-6-TH3 ● 6 A 8.08 6.25 6.46 6.68 6.92 7.46 9,060 EPDBEH20015-0.5-TH3 ● 0.075 0.15 0.5 0.12 0.13 45 4 A 14.14 0.55 0.56 0.58 0.60 0.65 19,930 EPDBEH2005-7-TH3 ● 7 A 7.48 7.28 7.53 7.79 8.07 8.71 10,740 EPDBEH20015-0.75-TH3 ● 0.75 A 13.71 0.81 0.83 0.86 0.89 0.96 21,690 EPDBEH2005-8-TH3 ● 8 A 6.96 8.31 8.60 8.90 9.22 9.95 10,740 EPDBEH20015-1-TH3 ● 1 A 13.30 1.06 1.10 1.14 1.18 1.27 21,690 EPDBEH2006-0.4-TH3 ● 0.4 － B 14.16 －－－－－ 7,420 EPDBEH2002-0.15-TH3 ● 0.15 － B 20.23 －－－－－ 12,850 EPDBEH2006-0.75-TH3 ● 0.75 A 13.94 0.82 0.84 0.86 0.88 0.93 7,420 EPDBEH2002-0.3-TH3 ● 0.3 A 14.54 0.34 0.35 0.36 0.37 0.39 12,850 EPDBEH2006-1-TH3 ● 1 A 13.47 1.08 1.10 1.13 1.17 1.24 7,420 EPDBEH2002-0.5-TH3 ● 0.5 A 14.17 0.55 0.56 0.58 0.60 0.64 12,850 EPDBEH2006-1.5-TH3 ● 1.5 A 12.61 1.59 1.64 1.69 1.74 1.86 6,600 EPDBEH2002-0.75-TH3 ● 0.75 A 13.73 0.81 0.83 0.86 0.89 0.95 12,850 EPDBEH2006-2-TH3 ● 2 A 11.86 2.11 2.17 2.24 2.31 2.48 6,600 EPDBEH2002-1-TH3 ● 1 A 13.32 1.06 1.10 1.13 1.17 1.26 12,850 EPDBEH2006-2.5-TH3 ● 2.5 A 11.19 2.63 2.71 2.80 2.89 3.10 6,760 0.1 0.2 0.15 0.18 50 4 EPDBEH2002-1.25-TH3 ● 1.25 A 12.93 1.32 1.37 1.41 1.46 1.57 13,920 EPDBEH2006-3-TH3 ● 3 A 10.59 3.14 3.24 3.35 3.46 3.72 6,760 EPDBEH2002-1.5-TH3 ● 1.5 A 12.56 1.58 1.63 1.69 1.75 1.88 13,920 EPDBEH2006-3.5-TH3 ● 3.5 A 10.05 3.66 3.78 3.90 4.04 4.34 7,060 EPDBEH2002-2-TH3 ● 2 A 11.89 2.10 2.17 2.24 2.32 2.50 15,330 EPDBEH2006-4-TH3 ● 4 A 9.56 4.18 4.31 4.46 4.61 4.97 7,060 0.3 0.6 0.4 0.57 50 4 EPDBEH2002-2.5-TH3 ● 2.5 A 11.28 2.61 2.70 2.80 2.90 3.13 16,750 EPDBEH2006-4.5-TH3 ● 4.5 A 9.12 4.69 4.85 5.01 5.19 5.59 7,060 EPDBEH2002-3-TH3 ● 3 A 10.73 3.13 3.24 3.35 3.47 3.75 17,920 EPDBEH2006-5-TH3 ● 5 A 8.71 5.21 5.38 5.57 5.76 6.21 7,060 EPDBEH2003-0.25-TH3 ● 0.25 － B 14.45 －－－－－ 12,620 EPDBEH2006-5.5-TH3 ● 5.5 A 8.34 5.73 5.92 6.12 6.34 6.83 7,060 EPDBEH2003-0.5-TH3 ● 0.5 A 14.21 0.56 0.58 0.60 0.61 0.65 12,620 EPDBEH2006-6-TH3 ● 6 A 8.00 6.24 6.45 6.67 6.91 7.45 7,060 EPDBEH2003-0.75-TH3 ● 0.75 A 13.76 0.82 0.85 0.87 0.90 0.96 12,620 EPDBEH2006-7-TH3 ● 7 A 7.40 7.28 7.52 7.78 8.06 8.70 7,980 EPDBEH2003-1-TH3 ● 1 A 13.33 1.08 1.11 1.15 1.19 1.27 12,620 EPDBEH2006-8-TH3 ● 8 A 6.88 8.31 8.59 8.89 9.21 9.94 9,350 EPDBEH2003-1.25-TH3 ● 1.25 A 12.93 1.34 1.38 1.43 1.47 1.58 13,450 EPDBEH2006-9-TH3 ● 9 A 6.43 9.35 9.66 10.00 10.36 11.18 9,970 EPDBEH2003-1.5-TH3 ● 0.15 0.3 1.5 0.25 0.27 50 4 A 12.56 1.60 1.65 1.70 1.76 1.89 13,450 EPDBEH2006-10-TH3 ● 10 A 6.03 10.38 10.73 11.11 11.51 12.43 9,520 EPDBEH2003-2-TH3 ● 2 A 11.86 2.12 2.18 2.26 2.34 2.52 13,450 EPDBEH2006-12-TH3 ● 12 A 5.37 12.45 12.87 13.32 13.81 14.91 10,740 EPDBEH2003-2.5-TH3 ● 2.5 A 11.24 2.63 2.72 2.81 2.91 3.14 13,920 EPDBEH2007-0.45-TH3 ● 0.45 － B 14.13 －－－－－ 6,600 EPDBEH2003-3-TH3 ● 3 A 10.68 3.15 3.25 3.37 3.49 3.76 13,920 EPDBEH2007-2-TH3 ● 2 A 11.85 2.11 2.17 2.24 2.31 2.47 6,600 EPDBEH2003-3.5-TH3 ● 3.5 A 10.18 3.67 3.79 3.92 4.06 4.38 13,920 EPDBEH2007-4-TH3 ● 0.35 0.7 4 0.45 0.67 50 4 A 9.50 4.18 4.31 4.45 4.61 4.95 7,060 EPDBEH2003-4-TH3 ● 4 A 9.72 4.18 4.32 4.47 4.64 5.00 14,150 EPDBEH2007-6-TH3 ● 6 A 7.92 6.24 6.45 6.67 6.91 7.44 7,060 EPDBEH2004-0.3-TH3 ● 0.3 － B 14.53 －－－－－ 8,600 EPDBEH2007-8-TH3 ● 8 A 6.79 8.31 8.59 8.89 9.21 9.93 7,060 EPDBEH2004-0.5-TH3 ● 0.5 A 14.28 0.56 0.58 0.59 0.60 0.64 8,600 EPDBEH2008-0.5-TH3 ● 0.5 － B 14.20 －－－－－ 6,600 EPDBEH2004-0.75-TH3 ● 0.75 A 13.81 0.82 0.84 0.87 0.89 0.95 8,600 EPDBEH2008-1-TH3 ● 1 A 13.58 1.07 1.10 1.12 1.15 1.21 6,600 EPDBEH2004-1-TH3 ● 1 A 13.37 1.08 1.11 1.14 1.18 1.26 8,600 EPDBEH2008-1.5-TH3 ● 1.5 A 12.66 1.59 1.63 1.68 1.73 1.83 6,600 EPDBEH2004-1.5-TH3 ● 1.5 A 12.57 1.60 1.65 1.70 1.75 1.88 8,740 EPDBEH2008-2-TH3 ● 2 A 11.85 2.11 2.17 2.23 2.30 2.46 6,600 EPDBEH2004-2-TH3 ● 2 A 11.86 2.11 2.18 2.25 2.33 2.50 9,060 EPDBEH2008-2.5-TH3 ● 2.5 A 11.14 2.62 2.70 2.79 2.88 3.08 6,850 0.2 0.4 0.3 0.37 50 4 EPDBEH2004-2.5-TH3 ● 2.5 A 11.23 2.63 2.72 2.81 2.90 3.13 9,350 EPDBEH2008-3-TH3 ● 3 A 10.51 3.14 3.24 3.34 3.45 3.70 7,060 0.4 0.8 0.5 0.77 50 4 EPDBEH2004-3-TH3 ● 3 A 10.65 3.15 3.25 3.36 3.48 3.75 9,970 EPDBEH2008-4-TH3 ● 4 A 9.44 4.17 4.31 4.45 4.60 4.94 7,060 EPDBEH2004-3.5-TH3 ● 3.5 A 10.14 3.66 3.78 3.91 4.05 4.37 10,740 EPDBEH2008-5-TH3 ● 5 A 8.57 5.21 5.38 5.56 5.75 6.19 7,060 EPDBEH2004-4-TH3 ● 4 A 9.67 4.18 4.32 4.47 4.63 4.99 10,740 EPDBEH2008-6-TH3 ● 6 A 7.84 6.24 6.45 6.66 6.90 7.43 7,060 EPDBEH2004-4.5-TH3 ● 4.5 A 9.24 4.70 4.85 5.02 5.20 5.61 11,360 EPDBEH2008-8-TH3 ● 8 A 6.70 8.31 8.58 8.88 9.20 9.92 7,060 EPDBEH2004-5-TH3 ● 5 A 8.85 5.21 5.39 5.58 5.78 6.23 11,360 EPDBEH2008-10-TH3 ● 10 A 5.85 10.38 10.72 11.10 11.50 12.40 9,350 EPDBEH2005-0.35-TH3 ● 0.35 － B 14.10 －－－－－ 8,600 EPDBEH2008-12-TH3 ● 12 A 5.19 12.44 12.86 13.31 13.80 14.89 11,500 EPDBEH2005-0.75-TH3 ● 0.75 A 13.88 0.82 0.84 0.86 0.88 0.94 8,600 EPDBEH2009-0.6-TH3 ● 0.6 － B 13.84 －－－－－ 6,600 EPDBEH2005-1-TH3 ● 0.25 0.5 1 0.35 0.47 50 4 A 13.42 1.08 1.11 1.14 1.17 1.25 8,600 EPDBEH2009-2-TH3 ● 2 A 11.85 2.11 2.16 2.23 2.29 2.44 6,600 EPDBEH2005-1.5-TH3 ● 1.5 A 12.59 1.59 1.64 1.69 1.75 1.87 8,600 EPDBEH2009-4-TH3 ● 0.45 0.9 4 0.6 0.87 50 4 A 9.38 4.17 4.30 4.44 4.59 4.93 7,060 EPDBEH2005-2-TH3 ● 2 A 11.86 2.11 2.18 2.25 2.32 2.49 8,600 EPDBEH2009-6-TH3 ● 6 A 7.75 6.24 6.44 6.66 6.89 7.42 7,060 ●：標準在庫品です。●：Stocked items. EPDBEH2009-8-TH3 ● 8 A 6.61 8.31 8.58 8.88 9.19 9.90 7,060 08 09 DC DN DCONMS DC BD2 DCONMS

Page9

ラインナップ Line Up レギュラーシャンクタイプ Regular shank type RE RE 2枚刃外周バックテーパ：2.5°～8.5° APMX 15° 15° 2 Flutes Back taper on peripheral edge LU LF LF LU・APMX 外周バックテーパ：2.5°～8.5° LB2 【注意】RE 2mm以上はバックドラフト形状ではありません。【Note】RE 2mm or larger does not have backdraft shape. Aタイプ Back taper on peripheral edge A type （㎜） Bタイプ B type Bタイプの詳細はP.13をご確認ください For details of B type, refer to page 13. ボール半径RE RE公差 Ball radius Tolerance on RE EPDBEH2 - . -(S6)-TH3 ねじれ30° 超硬 0.05～0.25 ±0.003 Carbide Helix angle 0.3～6 ±0.005 EPDBEH2 - . -(S6)-TH3 φ4 φ6～φ12 寸　法　Size(mm) 干渉角度勾配角に対する実有効首下長希望小売寸　法　Size(mm) 干渉角度勾配角に対する実有効首下長希望小売商品コード在庫ボール半径外径首下長刃長首径全長シャンク径タイプ Interference angle Effective under neck length 価格（円）商品コード在庫ボール半径外径首下長刃長首径全長シャンク径タイプ Interference angle Effective under neck length 価格（円） Item code Ball radius Tool dia. Under neck length Flute length Neck dia. Overall length Shank dia. Type （°） with respect to draft angle Stock Suggested retail price Item code with respect to draft angle Stock Ball radius Tool dia. Under neck length Flute length Neck dia. Overall length Shank dia. Type （°） Suggested retail price RE DC LU APMX DN LF DCONMS θκ 0.5° 1° 1.5° 2° 3° (￥) RE DC LU APMX DN LF DCONMS θκ 0.5° 1° 1.5° 2° 3° (￥) EPDBEH2001-0.08-TH3 ● 0.08 － B 20.93 －－－－－ 17,920 EPDBEH2005-2.5-TH3 ● 2.5 A 11.21 2.63 2.71 2.80 2.90 3.11 8,600 EPDBEH2001-0.2-TH3 ● 0.2 A 14.64 0.24 0.25 0.25 0.26 0.28 17,920 EPDBEH2005-3-TH3 ● 3 A 10.62 3.15 3.25 3.36 3.47 3.73 8,600 0.05 0.1 0.08 0.08 45 4 EPDBEH2001-0.3-TH3 ● 0.3 A 14.46 0.34 0.35 0.36 0.38 0.40 18,400 EPDBEH2005-4-TH3 ● 4 A 9.61 4.18 4.32 4.46 4.62 4.98 8,600 EPDBEH2001-0.5-TH3 ● 0.5 A 14.10 0.55 0.57 0.59 0.61 0.65 19,930 EPDBEH2005-5-TH3 ● 5 A 8.78 5.21 5.39 5.57 5.77 6.22 8,740 0.25 0.5 0.35 0.47 50 4 EPDBEH20015-0.12-TH3 ● 0.12 － B 15.25 －－－－－ 18,400 EPDBEH2005-5.5-TH3 ● 5.5 A 8.41 5.73 5.92 6.13 6.35 6.84 9,060 EPDBEH20015-0.3-TH3 ● 0.3 A 14.50 0.34 0.35 0.36 0.37 0.40 18,400 EPDBEH2005-6-TH3 ● 6 A 8.08 6.25 6.46 6.68 6.92 7.46 9,060 EPDBEH20015-0.5-TH3 ● 0.075 0.15 0.5 0.12 0.13 45 4 A 14.14 0.55 0.56 0.58 0.60 0.65 19,930 EPDBEH2005-7-TH3 ● 7 A 7.48 7.28 7.53 7.79 8.07 8.71 10,740 EPDBEH20015-0.75-TH3 ● 0.75 A 13.71 0.81 0.83 0.86 0.89 0.96 21,690 EPDBEH2005-8-TH3 ● 8 A 6.96 8.31 8.60 8.90 9.22 9.95 10,740 EPDBEH20015-1-TH3 ● 1 A 13.30 1.06 1.10 1.14 1.18 1.27 21,690 EPDBEH2006-0.4-TH3 ● 0.4 － B 14.16 －－－－－ 7,420 EPDBEH2002-0.15-TH3 ● 0.15 － B 20.23 －－－－－ 12,850 EPDBEH2006-0.75-TH3 ● 0.75 A 13.94 0.82 0.84 0.86 0.88 0.93 7,420 EPDBEH2002-0.3-TH3 ● 0.3 A 14.54 0.34 0.35 0.36 0.37 0.39 12,850 EPDBEH2006-1-TH3 ● 1 A 13.47 1.08 1.10 1.13 1.17 1.24 7,420 EPDBEH2002-0.5-TH3 ● 0.5 A 14.17 0.55 0.56 0.58 0.60 0.64 12,850 EPDBEH2006-1.5-TH3 ● 1.5 A 12.61 1.59 1.64 1.69 1.74 1.86 6,600 EPDBEH2002-0.75-TH3 ● 0.75 A 13.73 0.81 0.83 0.86 0.89 0.95 12,850 EPDBEH2006-2-TH3 ● 2 A 11.86 2.11 2.17 2.24 2.31 2.48 6,600 EPDBEH2002-1-TH3 ● 1 A 13.32 1.06 1.10 1.13 1.17 1.26 12,850 EPDBEH2006-2.5-TH3 ● 2.5 A 11.19 2.63 2.71 2.80 2.89 3.10 6,760 0.1 0.2 0.15 0.18 50 4 EPDBEH2002-1.25-TH3 ● 1.25 A 12.93 1.32 1.37 1.41 1.46 1.57 13,920 EPDBEH2006-3-TH3 ● 3 A 10.59 3.14 3.24 3.35 3.46 3.72 6,760 EPDBEH2002-1.5-TH3 ● 1.5 A 12.56 1.58 1.63 1.69 1.75 1.88 13,920 EPDBEH2006-3.5-TH3 ● 3.5 A 10.05 3.66 3.78 3.90 4.04 4.34 7,060 EPDBEH2002-2-TH3 ● 2 A 11.89 2.10 2.17 2.24 2.32 2.50 15,330 EPDBEH2006-4-TH3 ● 4 A 9.56 4.18 4.31 4.46 4.61 4.97 7,060 0.3 0.6 0.4 0.57 50 4 EPDBEH2002-2.5-TH3 ● 2.5 A 11.28 2.61 2.70 2.80 2.90 3.13 16,750 EPDBEH2006-4.5-TH3 ● 4.5 A 9.12 4.69 4.85 5.01 5.19 5.59 7,060 EPDBEH2002-3-TH3 ● 3 A 10.73 3.13 3.24 3.35 3.47 3.75 17,920 EPDBEH2006-5-TH3 ● 5 A 8.71 5.21 5.38 5.57 5.76 6.21 7,060 EPDBEH2003-0.25-TH3 ● 0.25 － B 14.45 －－－－－ 12,620 EPDBEH2006-5.5-TH3 ● 5.5 A 8.34 5.73 5.92 6.12 6.34 6.83 7,060 EPDBEH2003-0.5-TH3 ● 0.5 A 14.21 0.56 0.58 0.60 0.61 0.65 12,620 EPDBEH2006-6-TH3 ● 6 A 8.00 6.24 6.45 6.67 6.91 7.45 7,060 EPDBEH2003-0.75-TH3 ● 0.75 A 13.76 0.82 0.85 0.87 0.90 0.96 12,620 EPDBEH2006-7-TH3 ● 7 A 7.40 7.28 7.52 7.78 8.06 8.70 7,980 EPDBEH2003-1-TH3 ● 1 A 13.33 1.08 1.11 1.15 1.19 1.27 12,620 EPDBEH2006-8-TH3 ● 8 A 6.88 8.31 8.59 8.89 9.21 9.94 9,350 EPDBEH2003-1.25-TH3 ● 1.25 A 12.93 1.34 1.38 1.43 1.47 1.58 13,450 EPDBEH2006-9-TH3 ● 9 A 6.43 9.35 9.66 10.00 10.36 11.18 9,970 EPDBEH2003-1.5-TH3 ● 0.15 0.3 1.5 0.25 0.27 50 4 A 12.56 1.60 1.65 1.70 1.76 1.89 13,450 EPDBEH2006-10-TH3 ● 10 A 6.03 10.38 10.73 11.11 11.51 12.43 9,520 EPDBEH2003-2-TH3 ● 2 A 11.86 2.12 2.18 2.26 2.34 2.52 13,450 EPDBEH2006-12-TH3 ● 12 A 5.37 12.45 12.87 13.32 13.81 14.91 10,740 EPDBEH2003-2.5-TH3 ● 2.5 A 11.24 2.63 2.72 2.81 2.91 3.14 13,920 EPDBEH2007-0.45-TH3 ● 0.45 － B 14.13 －－－－－ 6,600 EPDBEH2003-3-TH3 ● 3 A 10.68 3.15 3.25 3.37 3.49 3.76 13,920 EPDBEH2007-2-TH3 ● 2 A 11.85 2.11 2.17 2.24 2.31 2.47 6,600 EPDBEH2003-3.5-TH3 ● 3.5 A 10.18 3.67 3.79 3.92 4.06 4.38 13,920 EPDBEH2007-4-TH3 ● 0.35 0.7 4 0.45 0.67 50 4 A 9.50 4.18 4.31 4.45 4.61 4.95 7,060 EPDBEH2003-4-TH3 ● 4 A 9.72 4.18 4.32 4.47 4.64 5.00 14,150 EPDBEH2007-6-TH3 ● 6 A 7.92 6.24 6.45 6.67 6.91 7.44 7,060 EPDBEH2004-0.3-TH3 ● 0.3 － B 14.53 －－－－－ 8,600 EPDBEH2007-8-TH3 ● 8 A 6.79 8.31 8.59 8.89 9.21 9.93 7,060 EPDBEH2004-0.5-TH3 ● 0.5 A 14.28 0.56 0.58 0.59 0.60 0.64 8,600 EPDBEH2008-0.5-TH3 ● 0.5 － B 14.20 －－－－－ 6,600 EPDBEH2004-0.75-TH3 ● 0.75 A 13.81 0.82 0.84 0.87 0.89 0.95 8,600 EPDBEH2008-1-TH3 ● 1 A 13.58 1.07 1.10 1.12 1.15 1.21 6,600 EPDBEH2004-1-TH3 ● 1 A 13.37 1.08 1.11 1.14 1.18 1.26 8,600 EPDBEH2008-1.5-TH3 ● 1.5 A 12.66 1.59 1.63 1.68 1.73 1.83 6,600 EPDBEH2004-1.5-TH3 ● 1.5 A 12.57 1.60 1.65 1.70 1.75 1.88 8,740 EPDBEH2008-2-TH3 ● 2 A 11.85 2.11 2.17 2.23 2.30 2.46 6,600 EPDBEH2004-2-TH3 ● 2 A 11.86 2.11 2.18 2.25 2.33 2.50 9,060 EPDBEH2008-2.5-TH3 ● 2.5 A 11.14 2.62 2.70 2.79 2.88 3.08 6,850 0.2 0.4 0.3 0.37 50 4 EPDBEH2004-2.5-TH3 ● 2.5 A 11.23 2.63 2.72 2.81 2.90 3.13 9,350 EPDBEH2008-3-TH3 ● 3 A 10.51 3.14 3.24 3.34 3.45 3.70 7,060 0.4 0.8 0.5 0.77 50 4 EPDBEH2004-3-TH3 ● 3 A 10.65 3.15 3.25 3.36 3.48 3.75 9,970 EPDBEH2008-4-TH3 ● 4 A 9.44 4.17 4.31 4.45 4.60 4.94 7,060 EPDBEH2004-3.5-TH3 ● 3.5 A 10.14 3.66 3.78 3.91 4.05 4.37 10,740 EPDBEH2008-5-TH3 ● 5 A 8.57 5.21 5.38 5.56 5.75 6.19 7,060 EPDBEH2004-4-TH3 ● 4 A 9.67 4.18 4.32 4.47 4.63 4.99 10,740 EPDBEH2008-6-TH3 ● 6 A 7.84 6.24 6.45 6.66 6.90 7.43 7,060 EPDBEH2004-4.5-TH3 ● 4.5 A 9.24 4.70 4.85 5.02 5.20 5.61 11,360 EPDBEH2008-8-TH3 ● 8 A 6.70 8.31 8.58 8.88 9.20 9.92 7,060 EPDBEH2004-5-TH3 ● 5 A 8.85 5.21 5.39 5.58 5.78 6.23 11,360 EPDBEH2008-10-TH3 ● 10 A 5.85 10.38 10.72 11.10 11.50 12.40 9,350 EPDBEH2005-0.35-TH3 ● 0.35 － B 14.10 －－－－－ 8,600 EPDBEH2008-12-TH3 ● 12 A 5.19 12.44 12.86 13.31 13.80 14.89 11,500 EPDBEH2005-0.75-TH3 ● 0.75 A 13.88 0.82 0.84 0.86 0.88 0.94 8,600 EPDBEH2009-0.6-TH3 ● 0.6 － B 13.84 －－－－－ 6,600 EPDBEH2005-1-TH3 ● 0.25 0.5 1 0.35 0.47 50 4 A 13.42 1.08 1.11 1.14 1.17 1.25 8,600 EPDBEH2009-2-TH3 ● 2 A 11.85 2.11 2.16 2.23 2.29 2.44 6,600 EPDBEH2005-1.5-TH3 ● 1.5 A 12.59 1.59 1.64 1.69 1.75 1.87 8,600 EPDBEH2009-4-TH3 ● 0.45 0.9 4 0.6 0.87 50 4 A 9.38 4.17 4.30 4.44 4.59 4.93 7,060 EPDBEH2005-2-TH3 ● 2 A 11.86 2.11 2.18 2.25 2.32 2.49 8,600 EPDBEH2009-6-TH3 ● 6 A 7.75 6.24 6.44 6.66 6.89 7.42 7,060 ●：標準在庫品です。●：Stocked items. EPDBEH2009-8-TH3 ● 8 A 6.61 8.31 8.58 8.88 9.19 9.90 7,060 08 09 DC DN DCONMS DC BD2 DCONMS

Page10

ラインナップ Line Up レギュラーシャンクタイプ Regular shank type RE RE 2枚刃外周バックテーパ：2.5°～8.5° APMX 15° 15° 2 Flutes Back taper on peripheral edge LU LF LF LU・APMX 外周バックテーパ：2.5°～8.5° LB2 【注意】RE 2mm以上はバックドラフト形状ではありません。【Note】RE 2mm or larger does not have backdraft shape. Aタイプ Back taper on peripheral edge A type Bタイプ B type Bタイプの詳細はP.13をご確認ください（㎜） For details of B type, refer to page 13. ボール半径RE RE公差 Ball radius Tolerance on RE EPDBEH2 - . -(S6)-TH3 ねじれ30° 超硬 0.05～0.25 ±0.003 0.3～6 ±0.005 EPDBEH2 - . -(S6)Carbide Helix angle -TH3 φ4 φ6～φ12 寸　法　Size(mm) 干渉角度勾配角に対する実有効首下長希望小売寸　法　Size(mm) 干渉角度勾配角に対する実有効首下長希望小売商品コード在庫ボール半径外径首下長刃長首径全長シャンク径タイプ Interference Effective under neck length 価格（円）商品コード在庫ボール半径外径首下長刃長首径全長シャンク径タイプ Interference angle angle Effective under neck length 価格（円） Item code Stock Ball radius Tool dia. Under neck length Flute length Neck dia. Overall length Shank dia. Type （°） with respect to draft angle Suggested Item code . Type （°） with respect to draft angle Stock Ball radius Tool dia. Under neck length Flute length Neck dia. Overall length Shank dia Suggested retail price retail price RE DC LU APMX DN LF DCONMS θκ 0.5° 1° 1.5° 2° 3° (￥) RE DC LU APMX DN LF DCONMS θκ 0.5° 1° 1.5° 2° 3° (￥) EPDBEH2010-0.8-TH3 ● 0.8 － B 13.47 －－－－－ 5,530 EPDBEH2015-6-TH3 ● 6 A 7.12 6.27 6.46 6.67 6.89 7.39 6,440 EPDBEH2010-1.5-TH3 ● 1.5 A 12.67 1.61 1.64 1.69 1.73 1.83 5,530 EPDBEH2015-8-TH3 ● 8 50 A 5.95 8.34 8.60 8.88 9.19 9.88 6,760 EPDBEH2010-2-TH3 ● 2 A 11.82 2.12 2.18 2.24 2.31 2.46 5,530 EPDBEH2015-10-TH3 ● 10 A 5.10 10.40 10.74 11.10 11.49 12.36 7,360 EPDBEH2010-2.5-TH3 ● 2.5 A 11.07 2.64 2.71 2.80 2.88 3.08 5,530 EPDBEH2015-12-TH3 ● 12 A 4.47 12.47 12.88 13.32 13.79 14.85 7,980 4 EPDBEH2010-3-TH3 ● 3 A 10.41 3.16 3.25 3.35 3.46 3.70 5,530 EPDBEH2015-14-TH3 ● 14 55 A 3.98 14.54 15.02 15.53 16.09 17.34 7,980 EPDBEH2010-4-TH3 ● 4 A 9.29 4.19 4.32 4.46 4.61 4.94 6,300 EPDBEH2015-16-TH3 ● 16 A 3.58 16.60 17.16 17.75 18.39 19.82 7,980 0.75 1.5 1.35 1.45 EPDBEH2010-5-TH3 ● 5 50 A 8.39 5.22 5.39 5.57 5.76 6.19 6,300 EPDBEH2015-18-TH3 ● 18 A 3.26 18.67 19.30 19.97 20.69 22.31 7,980 60 EPDBEH2010-6-TH3 ● 6 A 7.65 6.26 6.46 6.67 6.91 7.43 6,760 EPDBEH2015-20-TH3 ● 20 A 2.99 20.74 21.44 22.18 22.99 干渉なし 7,980 EPDBEH2010-7-TH3 ● 7 A 7.03 7.29 7.53 7.78 8.06 8.67 6,760 EPDBEH2015-3-S6-TH3 ● 3 A 11.84 3.17 3.25 3.34 3.44 3.66 9,660 4 EPDBEH2010-8-TH3 ● 8 A 6.50 8.32 8.60 8.89 9.21 9.91 6,760 EPDBEH2015-5-S6-TH3 ● 5 A 10.02 5.23 5.39 5.56 5.74 6.15 9,660 50 6 EPDBEH2010-9-TH3 ● 9 A 6.05 9.36 9.67 10.00 10.36 11.16 6,760 EPDBEH2015-8-S6-TH3 ● 8 A 8.14 8.34 8.60 8.88 9.19 9.88 10,120 EPDBEH2010-10-TH3 ● 0.5 1 10 0.8 0.96 A 5.65 10.39 10.74 11.11 11.51 12.40 6,760 EPDBEH2015-12-S6-TH3 ● 12 A 6.51 12.47 12.88 13.32 13.79 14.85 11,920 EPDBEH2010-12-TH3 ● 12 A 5.00 12.46 12.88 13.32 13.81 14.89 6,760 EPDBEH2016-4-TH3 ● 4 A 8.76 4.22 4.34 4.47 4.61 4.92 9,200 50 EPDBEH2010-13-TH3 ● 13 A 4.72 13.49 13.95 14.43 14.96 16.13 7,980 EPDBEH2016-8-TH3 ● 8 A 5.82 8.35 8.62 8.90 9.20 9.89 9,200 55 EPDBEH2010-14-TH3 ● 14 A 4.48 14.53 15.02 15.54 16.11 17.37 7,980 EPDBEH2016-12-TH3 ● 0.8 1.6 12 1.4 1.54 4 A 4.35 12.49 12.90 13.33 13.80 14.86 9,200 55 EPDBEH2010-16-TH3 ● 16 A 4.06 16.59 17.16 17.76 18.40 19.86 9,350 EPDBEH2016-16-TH3 ● 16 A 3.47 16.62 17.17 17.77 18.40 19.84 9,200 EPDBEH2010-18-TH3 ● 18 A 3.71 18.66 19.29 19.97 20.70 22.35 9,350 EPDBEH2016-20-TH3 ● 20 60 A 2.89 20.76 21.45 22.20 23.00 干渉なし 9,200 60 EPDBEH2010-20-TH3 ● 20 A 3.42 20.73 21.43 22.19 23.00 24.83 11,360 EPDBEH2018-4-TH3 ● 4 A 8.53 4.23 4.35 4.48 4.61 4.92 7,980 50 EPDBEH2010-2-S6-TH3 ● 2 A 12.92 2.12 2.18 2.24 2.31 2.46 8,290 EPDBEH2018-8-TH3 ● 8 A 5.55 8.37 8.63 8.91 9.21 9.89 7,980 EPDBEH2010-3-S6-TH3 ● 3 A 11.86 3.16 3.25 3.35 3.46 3.70 8,290 EPDBEH2018-12-TH3 ● 0.9 1.8 12 1.6 1.73 4 A 4.11 12.50 12.91 13.34 13.81 14.86 7,980 55 EPDBEH2010-6-S6-TH3 ● 6 50 6 A 9.53 6.26 6.46 6.67 6.91 7.43 10,120 EPDBEH2018-16-TH3 ● 16 A 3.26 16.64 17.19 17.78 18.41 19.83 7,980 EPDBEH2010-8-S6-TH3 ● 8 A 8.42 8.32 8.60 8.89 9.21 9.91 10,120 EPDBEH2018-20-TH3 ● 20 60 A 2.70 20.77 21.47 22.21 23.01 干渉なし 7,980 EPDBEH2010-10-S6-TH3 ● 10 A 7.54 10.39 10.74 11.11 11.51 12.40 10,120 EPDBEH2020-2.5-TH3 ● 2.5 A 10.60 2.66 2.72 2.78 2.85 3.01 5,530 EPDBEH2011-2-TH3 ● 2 A 11.78 2.14 2.20 2.26 2.32 2.47 7,420 EPDBEH2020-3-TH3 ● 3 A 9.72 3.18 3.25 3.34 3.43 3.63 5,530 EPDBEH2011-4-TH3 ● 4 A 9.20 4.21 4.34 4.47 4.62 4.95 8,440 EPDBEH2020-4-TH3 ● 4 A 8.32 4.21 4.32 4.45 4.58 4.87 5,530 EPDBEH2011-6-TH3 ● 0.55 1.1 6 1 1.05 50 4 A 7.54 6.28 6.47 6.69 6.92 7.44 9,200 EPDBEH2020-5-TH3 ● 5 50 A 7.27 5.25 5.39 5.55 5.73 6.11 6,300 EPDBEH2011-8-TH3 ● 8 A 6.39 8.34 8.61 8.91 9.22 9.93 9,200 EPDBEH2020-6-TH3 ● 6 A 6.46 6.28 6.46 6.66 6.88 7.36 6,300 EPDBEH2011-10-TH3 ● 10 A 5.54 10.41 10.75 11.12 11.52 12.41 9,200 EPDBEH2020-8-TH3 ● 8 A 5.27 8.35 8.60 8.88 9.18 9.84 6,760 EPDBEH2012-2-TH3 ● 2 A 11.78 2.14 2.19 2.25 2.31 2.46 8,440 EPDBEH2020-10-TH3 ● 10 A 4.46 10.41 10.74 11.10 11.48 12.33 6,760 EPDBEH2012-3-TH3 ● 3 A 10.29 3.17 3.26 3.36 3.46 3.70 8,440 EPDBEH2020-12-TH3 ● 12 A 3.86 12.48 12.88 13.31 13.77 14.82 6,760 EPDBEH2012-4-TH3 ● 4 A 9.13 4.21 4.33 4.47 4.61 4.94 8,440 EPDBEH2020-13-TH3 ● 13 A 3.62 13.51 13.95 14.42 14.92 16.06 6,760 50 55 4 EPDBEH2012-6-TH3 ● 6 4 A 7.45 6.27 6.47 6.68 6.91 7.43 9,200 EPDBEH2020-14-TH3 ● 14 A 3.40 14.55 15.02 15.53 16.07 17.30 6,760 EPDBEH2012-8-TH3 ● 0.6 1.2 8 1.1 1.15 A 6.29 8.34 8.61 8.90 9.21 9.91 9,200 EPDBEH2020-16-TH3 ● 16 A 3.04 16.62 17.16 17.75 18.37 19.79 6,760 EPDBEH2012-10-TH3 ● 10 A 5.44 10.41 10.75 11.12 11.51 12.40 9,200 EPDBEH2020-18-TH3 ● 18 A 2.75 18.68 19.30 19.96 20.67 干渉なし 6,760 EPDBEH2012-12-TH3 ● 12 55 A 4.79 12.48 12.89 13.33 13.81 14.89 9,200 EPDBEH2020-20-TH3 ● 1 2 20 1.7 1.94 60 A 2.51 20.75 21.44 22.18 22.97 干渉なし 6,760 EPDBEH2012-2-S6-TH3 ● 2 A 12.94 2.14 2.19 2.25 2.31 2.46 12,620 EPDBEH2020-22-TH3 ● 22 A 2.31 22.82 23.58 24.40 25.27 干渉なし 9,350 50 6 EPDBEH2012-4-S6-TH3 ● 4 A 10.92 4.21 4.33 4.47 4.61 4.94 12,620 EPDBEH2020-25-TH3 ● 25 65 A 2.06 25.92 26.79 27.72 28.72 干渉なし 9,520 EPDBEH2014-3-TH3 ● 3 A 10.15 3.19 3.28 3.37 3.47 3.70 7,980 EPDBEH2020-30-TH3 ● 30 70 A 1.75 31.09 32.14 33.26 干渉なし干渉なし 10,890 50 EPDBEH2014-8-TH3 ● 8 A 6.06 8.36 8.62 8.91 9.22 9.91 7,980 EPDBEH2020-35-TH3 ● 35 75 A 1.52 36.26 37.48 38.80 干渉なし干渉なし 14,730 0.7 1.4 1.3 1.34 4 EPDBEH2014-12-TH3 ● 12 A 4.58 12.49 12.90 13.34 13.82 14.89 7,980 EPDBEH2020-40-TH3 ● 40 80 A 1.34 41.42 42.83 干渉なし干渉なし干渉なし 14,730 55 EPDBEH2014-16-TH3 ● 16 A 3.68 16.63 17.18 17.78 18.42 19.86 7,980 EPDBEH2020-3-S6-TH3 ● 3 A 11.80 3.18 3.25 3.34 3.43 3.63 8,290 EPDBEH2015-2-TH3 ● 2 A 11.76 2.13 2.18 2.23 2.29 2.42 6,440 EPDBEH2020-6-S6-TH3 ● 6 A 9.04 6.28 6.46 6.66 6.88 7.36 9,430 EPDBEH2015-2.5-TH3 ● 2.5 A 10.88 2.65 2.72 2.79 2.87 3.04 6,440 EPDBEH2020-8-S6-TH3 ● 8 50 A 7.82 8.35 8.60 8.88 9.18 9.84 10,120 6 EPDBEH2015-3-TH3 ● 0.75 1.5 3 1.35 1.45 50 4 A 10.12 3.17 3.25 3.34 3.44 3.66 6,440 EPDBEH2020-12-S6-TH3 ● 12 A 6.15 12.48 12.88 13.31 13.77 14.82 10,120 EPDBEH2015-4-TH3 ● 4 A 8.88 4.20 4.32 4.45 4.59 4.91 6,440 EPDBEH2020-16-S6-TH3 ● 16 A 5.07 16.62 17.16 17.75 18.37 19.79 10,120 EPDBEH2015-5-TH3 ● 5 A 7.90 5.23 5.39 5.56 5.74 6.15 6,440 EPDBEH2020-20-S6-TH3 ● 20 60 A 4.31 20.75 21.44 22.18 22.97 24.76 10,120 ●：標準在庫品です。●：Stocked items. 干渉なし：No interference. 10 0191 DC DN DCONMS DC BD2 DCONMS

Page11

ラインナップ Line Up レギュラーシャンクタイプ Regular shank type RE RE 2枚刃外周バックテーパ：2.5°～8.5° APMX 15° 15° 2 Flutes Back taper on peripheral edge LU LF LF LU・APMX 外周バックテーパ：2.5°～8.5° LB2 【注意】RE 2mm以上はバックドラフト形状ではありません。【Note】RE 2mm or larger does not have backdraft shape. Aタイプ Back taper on peripheral edge A type Bタイプ B type Bタイプの詳細はP.13をご確認ください（㎜） For details of B type, refer to page 13. ボール半径RE RE公差 Ball radius Tolerance on RE EPDBEH2 - . -(S6)-TH3 ねじれ30° 超硬 0.05～0.25 ±0.003 0.3～6 ±0.005 EPDBEH2 - . -(S6)Carbide Helix angle -TH3 φ4 φ6～φ12 寸　法　Size(mm) 干渉角度勾配角に対する実有効首下長希望小売寸　法　Size(mm) 干渉角度勾配角に対する実有効首下長希望小売商品コード在庫ボール半径外径首下長刃長首径全長シャンク径タイプ Interference Effective under neck length 価格（円）商品コード在庫ボール半径外径首下長刃長首径全長シャンク径タイプ Interference angle angle Effective under neck length 価格（円） Item code Stock Ball radius Tool dia. Under neck length Flute length Neck dia. Overall length Shank dia. Type （°） with respect to draft angle Suggested Item code . Type （°） with respect to draft angle Stock Ball radius Tool dia. Under neck length Flute length Neck dia. Overall length Shank dia Suggested retail price retail price RE DC LU APMX DN LF DCONMS θκ 0.5° 1° 1.5° 2° 3° (￥) RE DC LU APMX DN LF DCONMS θκ 0.5° 1° 1.5° 2° 3° (￥) EPDBEH2010-0.8-TH3 ● 0.8 － B 13.47 －－－－－ 5,530 EPDBEH2015-6-TH3 ● 6 A 7.12 6.27 6.46 6.67 6.89 7.39 6,440 EPDBEH2010-1.5-TH3 ● 1.5 A 12.67 1.61 1.64 1.69 1.73 1.83 5,530 EPDBEH2015-8-TH3 ● 8 50 A 5.95 8.34 8.60 8.88 9.19 9.88 6,760 EPDBEH2010-2-TH3 ● 2 A 11.82 2.12 2.18 2.24 2.31 2.46 5,530 EPDBEH2015-10-TH3 ● 10 A 5.10 10.40 10.74 11.10 11.49 12.36 7,360 EPDBEH2010-2.5-TH3 ● 2.5 A 11.07 2.64 2.71 2.80 2.88 3.08 5,530 EPDBEH2015-12-TH3 ● 12 A 4.47 12.47 12.88 13.32 13.79 14.85 7,980 4 EPDBEH2010-3-TH3 ● 3 A 10.41 3.16 3.25 3.35 3.46 3.70 5,530 EPDBEH2015-14-TH3 ● 14 55 A 3.98 14.54 15.02 15.53 16.09 17.34 7,980 EPDBEH2010-4-TH3 ● 4 A 9.29 4.19 4.32 4.46 4.61 4.94 6,300 EPDBEH2015-16-TH3 ● 16 A 3.58 16.60 17.16 17.75 18.39 19.82 7,980 0.75 1.5 1.35 1.45 EPDBEH2010-5-TH3 ● 5 50 A 8.39 5.22 5.39 5.57 5.76 6.19 6,300 EPDBEH2015-18-TH3 ● 18 A 3.26 18.67 19.30 19.97 20.69 22.31 7,980 60 EPDBEH2010-6-TH3 ● 6 A 7.65 6.26 6.46 6.67 6.91 7.43 6,760 EPDBEH2015-20-TH3 ● 20 A 2.99 20.74 21.44 22.18 22.99 干渉なし 7,980 EPDBEH2010-7-TH3 ● 7 A 7.03 7.29 7.53 7.78 8.06 8.67 6,760 EPDBEH2015-3-S6-TH3 ● 3 A 11.84 3.17 3.25 3.34 3.44 3.66 9,660 4 EPDBEH2010-8-TH3 ● 8 A 6.50 8.32 8.60 8.89 9.21 9.91 6,760 EPDBEH2015-5-S6-TH3 ● 5 A 10.02 5.23 5.39 5.56 5.74 6.15 9,660 50 6 EPDBEH2010-9-TH3 ● 9 A 6.05 9.36 9.67 10.00 10.36 11.16 6,760 EPDBEH2015-8-S6-TH3 ● 8 A 8.14 8.34 8.60 8.88 9.19 9.88 10,120 EPDBEH2010-10-TH3 ● 0.5 1 10 0.8 0.96 A 5.65 10.39 10.74 11.11 11.51 12.40 6,760 EPDBEH2015-12-S6-TH3 ● 12 A 6.51 12.47 12.88 13.32 13.79 14.85 11,920 EPDBEH2010-12-TH3 ● 12 A 5.00 12.46 12.88 13.32 13.81 14.89 6,760 EPDBEH2016-4-TH3 ● 4 A 8.76 4.22 4.34 4.47 4.61 4.92 9,200 50 EPDBEH2010-13-TH3 ● 13 A 4.72 13.49 13.95 14.43 14.96 16.13 7,980 EPDBEH2016-8-TH3 ● 8 A 5.82 8.35 8.62 8.90 9.20 9.89 9,200 55 EPDBEH2010-14-TH3 ● 14 A 4.48 14.53 15.02 15.54 16.11 17.37 7,980 EPDBEH2016-12-TH3 ● 0.8 1.6 12 1.4 1.54 4 A 4.35 12.49 12.90 13.33 13.80 14.86 9,200 55 EPDBEH2010-16-TH3 ● 16 A 4.06 16.59 17.16 17.76 18.40 19.86 9,350 EPDBEH2016-16-TH3 ● 16 A 3.47 16.62 17.17 17.77 18.40 19.84 9,200 EPDBEH2010-18-TH3 ● 18 A 3.71 18.66 19.29 19.97 20.70 22.35 9,350 EPDBEH2016-20-TH3 ● 20 60 A 2.89 20.76 21.45 22.20 23.00 干渉なし 9,200 60 EPDBEH2010-20-TH3 ● 20 A 3.42 20.73 21.43 22.19 23.00 24.83 11,360 EPDBEH2018-4-TH3 ● 4 A 8.53 4.23 4.35 4.48 4.61 4.92 7,980 50 EPDBEH2010-2-S6-TH3 ● 2 A 12.92 2.12 2.18 2.24 2.31 2.46 8,290 EPDBEH2018-8-TH3 ● 8 A 5.55 8.37 8.63 8.91 9.21 9.89 7,980 EPDBEH2010-3-S6-TH3 ● 3 A 11.86 3.16 3.25 3.35 3.46 3.70 8,290 EPDBEH2018-12-TH3 ● 0.9 1.8 12 1.6 1.73 4 A 4.11 12.50 12.91 13.34 13.81 14.86 7,980 55 EPDBEH2010-6-S6-TH3 ● 6 50 6 A 9.53 6.26 6.46 6.67 6.91 7.43 10,120 EPDBEH2018-16-TH3 ● 16 A 3.26 16.64 17.19 17.78 18.41 19.83 7,980 EPDBEH2010-8-S6-TH3 ● 8 A 8.42 8.32 8.60 8.89 9.21 9.91 10,120 EPDBEH2018-20-TH3 ● 20 60 A 2.70 20.77 21.47 22.21 23.01 干渉なし 7,980 EPDBEH2010-10-S6-TH3 ● 10 A 7.54 10.39 10.74 11.11 11.51 12.40 10,120 EPDBEH2020-2.5-TH3 ● 2.5 A 10.60 2.66 2.72 2.78 2.85 3.01 5,530 EPDBEH2011-2-TH3 ● 2 A 11.78 2.14 2.20 2.26 2.32 2.47 7,420 EPDBEH2020-3-TH3 ● 3 A 9.72 3.18 3.25 3.34 3.43 3.63 5,530 EPDBEH2011-4-TH3 ● 4 A 9.20 4.21 4.34 4.47 4.62 4.95 8,440 EPDBEH2020-4-TH3 ● 4 A 8.32 4.21 4.32 4.45 4.58 4.87 5,530 EPDBEH2011-6-TH3 ● 0.55 1.1 6 1 1.05 50 4 A 7.54 6.28 6.47 6.69 6.92 7.44 9,200 EPDBEH2020-5-TH3 ● 5 50 A 7.27 5.25 5.39 5.55 5.73 6.11 6,300 EPDBEH2011-8-TH3 ● 8 A 6.39 8.34 8.61 8.91 9.22 9.93 9,200 EPDBEH2020-6-TH3 ● 6 A 6.46 6.28 6.46 6.66 6.88 7.36 6,300 EPDBEH2011-10-TH3 ● 10 A 5.54 10.41 10.75 11.12 11.52 12.41 9,200 EPDBEH2020-8-TH3 ● 8 A 5.27 8.35 8.60 8.88 9.18 9.84 6,760 EPDBEH2012-2-TH3 ● 2 A 11.78 2.14 2.19 2.25 2.31 2.46 8,440 EPDBEH2020-10-TH3 ● 10 A 4.46 10.41 10.74 11.10 11.48 12.33 6,760 EPDBEH2012-3-TH3 ● 3 A 10.29 3.17 3.26 3.36 3.46 3.70 8,440 EPDBEH2020-12-TH3 ● 12 A 3.86 12.48 12.88 13.31 13.77 14.82 6,760 EPDBEH2012-4-TH3 ● 4 A 9.13 4.21 4.33 4.47 4.61 4.94 8,440 EPDBEH2020-13-TH3 ● 13 A 3.62 13.51 13.95 14.42 14.92 16.06 6,760 50 55 4 EPDBEH2012-6-TH3 ● 6 4 A 7.45 6.27 6.47 6.68 6.91 7.43 9,200 EPDBEH2020-14-TH3 ● 14 A 3.40 14.55 15.02 15.53 16.07 17.30 6,760 EPDBEH2012-8-TH3 ● 0.6 1.2 8 1.1 1.15 A 6.29 8.34 8.61 8.90 9.21 9.91 9,200 EPDBEH2020-16-TH3 ● 16 A 3.04 16.62 17.16 17.75 18.37 19.79 6,760 EPDBEH2012-10-TH3 ● 10 A 5.44 10.41 10.75 11.12 11.51 12.40 9,200 EPDBEH2020-18-TH3 ● 18 A 2.75 18.68 19.30 19.96 20.67 干渉なし 6,760 EPDBEH2012-12-TH3 ● 12 55 A 4.79 12.48 12.89 13.33 13.81 14.89 9,200 EPDBEH2020-20-TH3 ● 1 2 20 1.7 1.94 60 A 2.51 20.75 21.44 22.18 22.97 干渉なし 6,760 EPDBEH2012-2-S6-TH3 ● 2 A 12.94 2.14 2.19 2.25 2.31 2.46 12,620 EPDBEH2020-22-TH3 ● 22 A 2.31 22.82 23.58 24.40 25.27 干渉なし 9,350 50 6 EPDBEH2012-4-S6-TH3 ● 4 A 10.92 4.21 4.33 4.47 4.61 4.94 12,620 EPDBEH2020-25-TH3 ● 25 65 A 2.06 25.92 26.79 27.72 28.72 干渉なし 9,520 EPDBEH2014-3-TH3 ● 3 A 10.15 3.19 3.28 3.37 3.47 3.70 7,980 EPDBEH2020-30-TH3 ● 30 70 A 1.75 31.09 32.14 33.26 干渉なし干渉なし 10,890 50 EPDBEH2014-8-TH3 ● 8 A 6.06 8.36 8.62 8.91 9.22 9.91 7,980 EPDBEH2020-35-TH3 ● 35 75 A 1.52 36.26 37.48 38.80 干渉なし干渉なし 14,730 0.7 1.4 1.3 1.34 4 EPDBEH2014-12-TH3 ● 12 A 4.58 12.49 12.90 13.34 13.82 14.89 7,980 EPDBEH2020-40-TH3 ● 40 80 A 1.34 41.42 42.83 干渉なし干渉なし干渉なし 14,730 55 EPDBEH2014-16-TH3 ● 16 A 3.68 16.63 17.18 17.78 18.42 19.86 7,980 EPDBEH2020-3-S6-TH3 ● 3 A 11.80 3.18 3.25 3.34 3.43 3.63 8,290 EPDBEH2015-2-TH3 ● 2 A 11.76 2.13 2.18 2.23 2.29 2.42 6,440 EPDBEH2020-6-S6-TH3 ● 6 A 9.04 6.28 6.46 6.66 6.88 7.36 9,430 EPDBEH2015-2.5-TH3 ● 2.5 A 10.88 2.65 2.72 2.79 2.87 3.04 6,440 EPDBEH2020-8-S6-TH3 ● 8 50 A 7.82 8.35 8.60 8.88 9.18 9.84 10,120 6 EPDBEH2015-3-TH3 ● 0.75 1.5 3 1.35 1.45 50 4 A 10.12 3.17 3.25 3.34 3.44 3.66 6,440 EPDBEH2020-12-S6-TH3 ● 12 A 6.15 12.48 12.88 13.31 13.77 14.82 10,120 EPDBEH2015-4-TH3 ● 4 A 8.88 4.20 4.32 4.45 4.59 4.91 6,440 EPDBEH2020-16-S6-TH3 ● 16 A 5.07 16.62 17.16 17.75 18.37 19.79 10,120 EPDBEH2015-5-TH3 ● 5 A 7.90 5.23 5.39 5.56 5.74 6.15 6,440 EPDBEH2020-20-S6-TH3 ● 20 60 A 4.31 20.75 21.44 22.18 22.97 24.76 10,120 ●：標準在庫品です。●：Stocked items. 干渉なし：No interference. 10 0191 DC DN DCONMS DC BD2 DCONMS

Page12

ラインナップ Line Up レギュラーシャンクタイプ Regular shank type RE ストロングネックタイプ× ショートシャンクタイプ Strong neck type × Short shank type 2枚刃外周バックテーパ：2.5°～8.5° APMX 15° 2 Flutes Back taper on peripheral edge LU LF RE 【注意】RE 2mm以上はバックドラフト形状ではありません。 2枚刃【Note】RE 2mm or larger does not have backdraft shape. Aタイプ A type 2 Flutes 15° （㎜） LF ボール半径RE RE公差 Ball radius Tolerance on RE LU・APMX 外周バックテーパ：2.5°～8.5° LB2 Back taper on peripheral edge EPDBEH2 - . -(S6)-TH3 ねじれ30° 超硬 0.05～0.25 ±0.003 （㎜） Carbide Helix angle 0.3～6 ±0.005 φ4 φ6～φ12 ボール半径RE RE公差 Ball radius Tolerance on RE 寸　法　Size(mm) 干渉角度勾配角に対する実有効首下長希望小売ねじれ30° 商品コード在庫ボール半径外径首下長刃長首径全長シャンク径タイプ Interference angle Effective under neck length 価格（円） EPDBEH2 F- . -TH3 超硬 0.05～0.25 ±0.003 Carbide Helix angle 0.3～0.5 ±0.005 Item code Stock Ball radius Tool dia. Under neck length Flute length Neck dia. Overall length Shank dia. Type （°） with respect to draft angle Suggested retail price RE DC LU APMX DN LF DCONMS θκ 0.5° 1° 1.5° 2° 3° ( 寸　法　Size(mm) ￥) 干渉角度 EPDBEH2025-6-TH3 ● 商品コード在庫 6 A 5.54 6.35 6.53 6.72 6.92 7.39 8,500 ボール半径外径首下長刃長全長シャンク径首寸法 Interference 希望小売 angle 価格（円） 50 Item code Stock Ball radius Tool dia. Under neck length Flute length Overall length Shank dia. Neck size （°） Suggested EPDBEH2025-10-TH3 ● 10 A 3.66 10.48 10.81 11.15 11.52 12.36 9,060 RE DC LU APMX LF DCONMS LB2 BD2 θκ retail price(￥) EPDBEH2025-15-TH3 ● 15 55 A 2.57 15.65 16.15 16.69 17.27 干渉なし 9,220 EPDBEH2001F-0.08-TH3 ★ 0.05 0.1 0.08 0.08 35 4 0.2 0.13 20.93 17,920 2.4 4 EPDBEH2025-20-TH3 ● 1.25 2.5 2 20 60 A 1.98 20.82 21.50 22.23 干渉なし干渉なし 10,820 EPDBEH20015F-0.12-TH3 ★ 0.075 0.15 0.12 0.12 35 4 0.3 0.18 15.25 18,400 EPDBEH2025-25-TH3 ● 25 65 A 1.61 25.99 26.85 27.78 干渉なし干渉なし 11,510 EPDBEH2002F-0.15-TH3 ★ 0.1 0.2 0.15 0.15 35 4 0.3 0.25 20.23 12,850 EPDBEH2025-30-TH3 ● 30 70 A 1.36 31.16 32.20 干渉なし干渉なし干渉なし 13,330 EPDBEH2003F-0.25-TH3 ★ 0.15 0.3 0.25 0.25 35 4 0.5 0.35 14.45 12,620 EPDBEH2030-6-TH3 ● 6 50 A 8.27 6.38 6.55 6.73 6.93 7.38 6,900 EPDBEH2004F-0.3-TH3 ★ 0.2 0.4 0.3 0.3 35 4 0.5 0.45 14.53 8,600 EPDBEH2030-8-TH3 ● 8 A 6.95 8.45 8.69 8.95 9.23 9.86 6,900 EPDBEH2005F-0.35-TH3 ★ 0.25 0.5 0.35 0.35 35 4 0.75 0.55 14.10 8,600 55 EPDBEH2030-10-TH3 ● 10 A 5.98 10.51 10.83 11.17 11.53 12.35 7,980 EPDBEH2006F-0.4-TH3 ★ 0.3 0.6 0.4 0.4 35 4 0.75 0.65 14.16 7,420 EPDBEH2030-13-TH3 ● 13 A 4.95 13.61 14.04 14.49 14.98 16.08 9,120 EPDBEH2007F-0.45-TH3 ★ 0.35 0.7 0.45 0.45 35 4 0.8 0.75 14.13 6,600 EPDBEH2030-16-TH3 ● 60 1.5 3 16 2.5 2.88 6 A 4.23 16.71 17.25 17.82 18.43 19.81 9,220 EPDBEH2008F-0.5-TH3 ★ 0.4 0.8 0.5 0.5 35 4 0.8 0.85 14.20 6,600 EPDBEH2030-20-TH3 ● 20 65 A 3.53 20.85 21.52 22.25 23.03 24.78 8,870 EPDBEH2009F-0.6-TH3 ★ 0.45 0.9 0.6 0.6 35 4 1 0.95 13.84 6,600 ● EPDBEH2030-25-TH3 EPDBEH2010F-0.8-TH3 ★ 0.5 1 0.8 0.8 35 4 1.2 1.05 13.47 5,530 25 70 A 2.93 26.02 26.87 27.79 28.78 干渉なし 8,870 EPDBEH2030-30-TH3 ● 30 75 A 2.51 31.19 32.22 33.33 34.53 干渉なし 10,110 ● EPDBEH2030-35-TH3 35 80 A 2.19 36.35 37.57 38.87 40.28 干渉なし 12,740 ● EPDBEH2035-10-TH3 10 55 A 5.42 10.56 10.87 11.20 11.56 12.36 11,310 ストロングネックタイプ Strong neck type EPDBEH2035-15-TH3 ● 15 60 A 3.94 15.73 16.22 16.74 17.31 18.58 11,700 EPDBEH2035-25-TH3 ● 1.75 3.5 25 2.75 3.35 70 6 A 2.54 26.07 26.92 27.83 28.81 干渉なし 12,380 2枚刃 EPDBEH2035-35-TH3 ● 35 80 A 1.88 36.40 37.61 38.91 干渉なし干渉なし 15,910 ● 2 Flutes EPDBEH2035-45-TH3 45 90 A 1.49 46.74 48.31 干渉なし干渉なし干渉なし 19,450 EPDBEH2040-8-TH3 ● 8 A 5.71 8.49 8.71 8.96 9.22 9.81 7,100 55 ● EPDBEH2040-10-TH3 10 A 4.76 10.55 10.85 11.17 11.52 12.30 7,100 EPDBEH2 - . -TH3 EPDBEH2040-12-TH3 ● 12 A 4.09 12.62 12.99 13.39 13.82 14.79 9,220 寸　法　Size(mm) EPDBEH2040-13-TH3 ● 13 60 A 3.82 13.65 14.06 14.50 14.97 16.03 9,220 干渉角度商品コード在庫ボール半径外径首下長刃長全長シャンク径首寸法 Interference 希望小売 angle EPDBEH2040-16-TH3 ● 16 A 3.18 16.76 17.27 17.82 18.42 19.76 9,220 価格（円） Item code Stock Ball radius Tool dia. Under neck length Flute length Overall length Shank dia. Neck size （°） Suggested EPDBEH2040-20-TH3 ● 20 65 A 2.61 20.89 21.55 22.26 23.02 干渉なし 9,220 RE DC LU APMX LF DCONMS LB2 BD2 θκ retail price(￥) 6 ● 2 4 3 3.85 EPDBEH2040-25-TH3 25 70 A 2.13 26.06 26.90 27.80 28.77 干渉なし 9,220 EPDBEH2001-0.08-TH3 ● 0.05 0.1 0.08 0.08 45 4 0.2 0.13 20.93 17,920 EPDBEH2040-30-TH3 ● 30 75 A 1.79 31.23 32.25 33.34 干渉なし干渉なし 9,220 EPDBEH20015-0.12-TH3 ● 0.075 0.15 0.12 0.12 45 4 0.3 0.18 15.25 18,400 ● EPDBEH2040-35-TH3 35 A 1.55 36.40 37.60 38.88 干渉なし干渉なし 10,630 EPDBEH2002-0.15-TH3 ● 0.1 0.2 0.15 0.15 50 4 0.3 0.25 20.23 12,850 80 EPDBEH2040-40-TH3 ● 40 A 1.37 41.56 42.94 干渉なし干渉なし干渉なし 11,920 EPDBEH2003-0.25-TH3 ● 0.15 0.3 0.25 0.25 50 4 0.5 0.35 14.45 12,620 EPDBEH2040-45-TH3 ● 45 90 A 1.22 46.73 48.29 干渉なし干渉なし干渉なし 15,450 EPDBEH2004-0.3-TH3 ● 0.2 0.4 0.3 0.3 50 4 0.5 0.45 14.53 8,600 EPDBEH2040-50-TH3 ● 50 100 A 1.11 51.90 53.64 干渉なし干渉なし干渉なし 16,860 EPDBEH2005-0.35-TH3 ● 0.25 0.5 0.35 0.35 50 4 0.75 0.55 14.10 8,600 EPDBEH2050-10-TH3 ● 10 55 2.97 EPDBEH2006-0.4-TH3 ● A 10.54 10.82 11.12 11.45 干渉なし 14,580 0.3 0.6 0.4 0.4 50 4 0.75 0.65 14.16 7,420 EPDBEH2007-0.45-TH3 ● 0.35 0.7 0.45 0.45 50 4 0.8 0.75 14.13 6,600 EPDBEH2050-20-TH3 ● 20 65 A 1.46 20.87 21.52 干渉なし干渉なし干渉なし 16,190 EPDBEH2008-0.5-TH3 ● 0.4 0.8 0.5 0.5 50 4 0.8 0.85 14.20 6,600 EPDBEH2050-25-TH3 ● 2.5 5 25 3.5 4.85 70 6 A 1.17 26.04 26.86 干渉なし干渉なし干渉なし 16,190 EPDBEH2009-0.6-TH3 ● 0.45 0.9 0.6 0.6 50 4 1 0.95 13.84 6,600 EPDBEH2050-30-TH3 ● 30 75 A 0.97 31.21 干渉なし干渉なし干渉なし干渉なし 17,290 EPDBEH2010-0.8-TH3 ● 0.5 1 0.8 0.8 50 4 1.2 1.05 13.47 5,530 EPDBEH2050-40-TH3 ● 40 80 A 0.73 41.55 干渉なし干渉なし干渉なし干渉なし 21,490 EPDBEH2060-12-TH3 ● 12 60 A 0 干渉なし干渉なし干渉なし干渉なし干渉なし 12,060 EPDBEH2060-20-TH3 ● 20 65 A 0 干渉なし干渉なし干渉なし干渉なし干渉なし 12,060 6 ● 3 6 6 5.85 EPDBEH2060-30-TH3 30 75 A 0 干渉なし干渉なし干渉なし干渉なし干渉なし 12,490 EPDBEH2060-50-TH3 ● 50 100 A 0 干渉なし干渉なし干渉なし干渉なし干渉なし 14,700 EPDBEH2080-24-TH3 ● 4 8 24 12 7.6 100 8 A 0 干渉なし干渉なし干渉なし干渉なし干渉なし 17,660 EPDBEH2100-30-TH3 ● 5 10 30 15 9.5 100 10 A 0 干渉なし干渉なし干渉なし干渉なし干渉なし 21,980 EPDBEH2120-36-TH3 ● 6 12 36 18 11.5 110 12 A 0 干渉なし干渉なし干渉なし干渉なし干渉なし 28,530 ●：標準在庫品です。●：Stocked items.　★：新商品の標準在庫品です。★：Stocked items of new products.　干渉なし：No interference. 12 113 DC DN DCONMS DC BD2 DCONMS

Page13

ラインナップ Line Up レギュラーシャンクタイプ Regular shank type RE ストロングネックタイプ× ショートシャンクタイプ Strong neck type × Short shank type 2枚刃外周バックテーパ：2.5°～8.5° APMX 15° 2 Flutes Back taper on peripheral edge LU LF RE 【注意】RE 2mm以上はバックドラフト形状ではありません。 2枚刃【Note】RE 2mm or larger does not have backdraft shape. Aタイプ A type 2 Flutes 15° （㎜） LF ボール半径RE RE公差 Ball radius Tolerance on RE LU・APMX 外周バックテーパ：2.5°～8.5° LB2 Back taper on peripheral edge EPDBEH2 - . -(S6)-TH3 ねじれ30° 超硬 0.05～0.25 ±0.003 （㎜） Carbide Helix angle 0.3～6 ±0.005 φ4 φ6～φ12 ボール半径RE RE公差 Ball radius Tolerance on RE 寸　法　Size(mm) 干渉角度勾配角に対する実有効首下長希望小売ねじれ30° 商品コード在庫ボール半径外径首下長刃長首径全長シャンク径タイプ Interference angle Effective under neck length 価格（円） EPDBEH2 F- . -TH3 超硬 0.05～0.25 ±0.003 Carbide Helix angle 0.3～0.5 ±0.005 Item code Stock Ball radius Tool dia. Under neck length Flute length Neck dia. Overall length Shank dia. Type （°） with respect to draft angle Suggested retail price RE DC LU APMX DN LF DCONMS θκ 0.5° 1° 1.5° 2° 3° ( 寸　法　Size(mm) ￥) 干渉角度 EPDBEH2025-6-TH3 ● 商品コード在庫 6 A 5.54 6.35 6.53 6.72 6.92 7.39 8,500 ボール半径外径首下長刃長全長シャンク径首寸法 Interference 希望小売 angle 価格（円） 50 Item code Stock Ball radius Tool dia. Under neck length Flute length Overall length Shank dia. Neck size （°） Suggested EPDBEH2025-10-TH3 ● 10 A 3.66 10.48 10.81 11.15 11.52 12.36 9,060 RE DC LU APMX LF DCONMS LB2 BD2 θκ retail price(￥) EPDBEH2025-15-TH3 ● 15 55 A 2.57 15.65 16.15 16.69 17.27 干渉なし 9,220 EPDBEH2001F-0.08-TH3 ★ 0.05 0.1 0.08 0.08 35 4 0.2 0.13 20.93 17,920 2.4 4 EPDBEH2025-20-TH3 ● 1.25 2.5 2 20 60 A 1.98 20.82 21.50 22.23 干渉なし干渉なし 10,820 EPDBEH20015F-0.12-TH3 ★ 0.075 0.15 0.12 0.12 35 4 0.3 0.18 15.25 18,400 EPDBEH2025-25-TH3 ● 25 65 A 1.61 25.99 26.85 27.78 干渉なし干渉なし 11,510 EPDBEH2002F-0.15-TH3 ★ 0.1 0.2 0.15 0.15 35 4 0.3 0.25 20.23 12,850 EPDBEH2025-30-TH3 ● 30 70 A 1.36 31.16 32.20 干渉なし干渉なし干渉なし 13,330 EPDBEH2003F-0.25-TH3 ★ 0.15 0.3 0.25 0.25 35 4 0.5 0.35 14.45 12,620 EPDBEH2030-6-TH3 ● 6 50 A 8.27 6.38 6.55 6.73 6.93 7.38 6,900 EPDBEH2004F-0.3-TH3 ★ 0.2 0.4 0.3 0.3 35 4 0.5 0.45 14.53 8,600 EPDBEH2030-8-TH3 ● 8 A 6.95 8.45 8.69 8.95 9.23 9.86 6,900 EPDBEH2005F-0.35-TH3 ★ 0.25 0.5 0.35 0.35 35 4 0.75 0.55 14.10 8,600 55 EPDBEH2030-10-TH3 ● 10 A 5.98 10.51 10.83 11.17 11.53 12.35 7,980 EPDBEH2006F-0.4-TH3 ★ 0.3 0.6 0.4 0.4 35 4 0.75 0.65 14.16 7,420 EPDBEH2030-13-TH3 ● 13 A 4.95 13.61 14.04 14.49 14.98 16.08 9,120 EPDBEH2007F-0.45-TH3 ★ 0.35 0.7 0.45 0.45 35 4 0.8 0.75 14.13 6,600 EPDBEH2030-16-TH3 ● 60 1.5 3 16 2.5 2.88 6 A 4.23 16.71 17.25 17.82 18.43 19.81 9,220 EPDBEH2008F-0.5-TH3 ★ 0.4 0.8 0.5 0.5 35 4 0.8 0.85 14.20 6,600 EPDBEH2030-20-TH3 ● 20 65 A 3.53 20.85 21.52 22.25 23.03 24.78 8,870 EPDBEH2009F-0.6-TH3 ★ 0.45 0.9 0.6 0.6 35 4 1 0.95 13.84 6,600 ● EPDBEH2030-25-TH3 EPDBEH2010F-0.8-TH3 ★ 0.5 1 0.8 0.8 35 4 1.2 1.05 13.47 5,530 25 70 A 2.93 26.02 26.87 27.79 28.78 干渉なし 8,870 EPDBEH2030-30-TH3 ● 30 75 A 2.51 31.19 32.22 33.33 34.53 干渉なし 10,110 ● EPDBEH2030-35-TH3 35 80 A 2.19 36.35 37.57 38.87 40.28 干渉なし 12,740 ● EPDBEH2035-10-TH3 10 55 A 5.42 10.56 10.87 11.20 11.56 12.36 11,310 ストロングネックタイプ Strong neck type EPDBEH2035-15-TH3 ● 15 60 A 3.94 15.73 16.22 16.74 17.31 18.58 11,700 EPDBEH2035-25-TH3 ● 1.75 3.5 25 2.75 3.35 70 6 A 2.54 26.07 26.92 27.83 28.81 干渉なし 12,380 2枚刃 EPDBEH2035-35-TH3 ● 35 80 A 1.88 36.40 37.61 38.91 干渉なし干渉なし 15,910 ● 2 Flutes EPDBEH2035-45-TH3 45 90 A 1.49 46.74 48.31 干渉なし干渉なし干渉なし 19,450 EPDBEH2040-8-TH3 ● 8 A 5.71 8.49 8.71 8.96 9.22 9.81 7,100 55 ● EPDBEH2040-10-TH3 10 A 4.76 10.55 10.85 11.17 11.52 12.30 7,100 EPDBEH2 - . -TH3 EPDBEH2040-12-TH3 ● 12 A 4.09 12.62 12.99 13.39 13.82 14.79 9,220 寸　法　Size(mm) EPDBEH2040-13-TH3 ● 13 60 A 3.82 13.65 14.06 14.50 14.97 16.03 9,220 干渉角度商品コード在庫ボール半径外径首下長刃長全長シャンク径首寸法 Interference 希望小売 angle EPDBEH2040-16-TH3 ● 16 A 3.18 16.76 17.27 17.82 18.42 19.76 9,220 価格（円） Item code Stock Ball radius Tool dia. Under neck length Flute length Overall length Shank dia. Neck size （°） Suggested EPDBEH2040-20-TH3 ● 20 65 A 2.61 20.89 21.55 22.26 23.02 干渉なし 9,220 RE DC LU APMX LF DCONMS LB2 BD2 θκ retail price(￥) 6 ● 2 4 3 3.85 EPDBEH2040-25-TH3 25 70 A 2.13 26.06 26.90 27.80 28.77 干渉なし 9,220 EPDBEH2001-0.08-TH3 ● 0.05 0.1 0.08 0.08 45 4 0.2 0.13 20.93 17,920 EPDBEH2040-30-TH3 ● 30 75 A 1.79 31.23 32.25 33.34 干渉なし干渉なし 9,220 EPDBEH20015-0.12-TH3 ● 0.075 0.15 0.12 0.12 45 4 0.3 0.18 15.25 18,400 ● EPDBEH2040-35-TH3 35 A 1.55 36.40 37.60 38.88 干渉なし干渉なし 10,630 EPDBEH2002-0.15-TH3 ● 0.1 0.2 0.15 0.15 50 4 0.3 0.25 20.23 12,850 80 EPDBEH2040-40-TH3 ● 40 A 1.37 41.56 42.94 干渉なし干渉なし干渉なし 11,920 EPDBEH2003-0.25-TH3 ● 0.15 0.3 0.25 0.25 50 4 0.5 0.35 14.45 12,620 EPDBEH2040-45-TH3 ● 45 90 A 1.22 46.73 48.29 干渉なし干渉なし干渉なし 15,450 EPDBEH2004-0.3-TH3 ● 0.2 0.4 0.3 0.3 50 4 0.5 0.45 14.53 8,600 EPDBEH2040-50-TH3 ● 50 100 A 1.11 51.90 53.64 干渉なし干渉なし干渉なし 16,860 EPDBEH2005-0.35-TH3 ● 0.25 0.5 0.35 0.35 50 4 0.75 0.55 14.10 8,600 EPDBEH2050-10-TH3 ● 10 55 2.97 EPDBEH2006-0.4-TH3 ● A 10.54 10.82 11.12 11.45 干渉なし 14,580 0.3 0.6 0.4 0.4 50 4 0.75 0.65 14.16 7,420 EPDBEH2007-0.45-TH3 ● 0.35 0.7 0.45 0.45 50 4 0.8 0.75 14.13 6,600 EPDBEH2050-20-TH3 ● 20 65 A 1.46 20.87 21.52 干渉なし干渉なし干渉なし 16,190 EPDBEH2008-0.5-TH3 ● 0.4 0.8 0.5 0.5 50 4 0.8 0.85 14.20 6,600 EPDBEH2050-25-TH3 ● 2.5 5 25 3.5 4.85 70 6 A 1.17 26.04 26.86 干渉なし干渉なし干渉なし 16,190 EPDBEH2009-0.6-TH3 ● 0.45 0.9 0.6 0.6 50 4 1 0.95 13.84 6,600 EPDBEH2050-30-TH3 ● 30 75 A 0.97 31.21 干渉なし干渉なし干渉なし干渉なし 17,290 EPDBEH2010-0.8-TH3 ● 0.5 1 0.8 0.8 50 4 1.2 1.05 13.47 5,530 EPDBEH2050-40-TH3 ● 40 80 A 0.73 41.55 干渉なし干渉なし干渉なし干渉なし 21,490 EPDBEH2060-12-TH3 ● 12 60 A 0 干渉なし干渉なし干渉なし干渉なし干渉なし 12,060 EPDBEH2060-20-TH3 ● 20 65 A 0 干渉なし干渉なし干渉なし干渉なし干渉なし 12,060 6 ● 3 6 6 5.85 EPDBEH2060-30-TH3 30 75 A 0 干渉なし干渉なし干渉なし干渉なし干渉なし 12,490 EPDBEH2060-50-TH3 ● 50 100 A 0 干渉なし干渉なし干渉なし干渉なし干渉なし 14,700 EPDBEH2080-24-TH3 ● 4 8 24 12 7.6 100 8 A 0 干渉なし干渉なし干渉なし干渉なし干渉なし 17,660 EPDBEH2100-30-TH3 ● 5 10 30 15 9.5 100 10 A 0 干渉なし干渉なし干渉なし干渉なし干渉なし 21,980 EPDBEH2120-36-TH3 ● 6 12 36 18 11.5 110 12 A 0 干渉なし干渉なし干渉なし干渉なし干渉なし 28,530 ●：標準在庫品です。●：Stocked items.　★：新商品の標準在庫品です。★：Stocked items of new products.　干渉なし：No interference. 12 113 DC DN DCONMS DC BD2 DCONMS

Page14

標準切削条件表 Recommended Cut t ing Condi t ions 高能率切削条件高精度切削条件高能率切削条件高精度切削条件 High efficiency cuttiing condition High accuracy cuttiing condition 高精度切削条件は18ページを参照してください。Please refer to P.18 about high accuracy cutting conditions High efficiency cuttiing condition High accuracy cuttiing condition 高精度切削条件は18ページを参照してください。Please refer to P.18 about high accuracy cutting conditions 1 2 3 4 5 1 2 3 4 5 被削材プリハードン鋼焼入れ鋼焼入れ鋼焼入れ鋼焼入れ鋼被削材プリハードン鋼焼入れ鋼焼入れ鋼焼入れ鋼焼入れ鋼 Work material Pre-hardened steels Hardened steels Hardened steels Hardened steels Hardened steels （35～45HRC）（45～55HRC）（55～65HRC）（65～68HRC）（68～72HRC） Work material Pre-hardened steels Hardened steels Hardened steels Hardened steels Hardened steels （35～45HRC）（45～55HRC）（55～65HRC）（65～68HRC）（68～72HRC）切り込み比率 Ratio to standard depth of cut 100% 85% 80% 65% 55% 切り込み比率 Ratio to standard depth of cut 100% 85% 80% 65% 55% ボール半径RE 外径DC 首下長LU 回転数送り速度回転数送り速度回転数送り速度回転数送り速度回転数送り速度ボール半径RE 外径DC 首下長LU 回転数送り速度回転数送り速度回転数送り速度回転数送り速度回転数送り速度 Ball radius Tool dia. Under neck ap n v f n v f n v f Bal Under neck ap l radius Tool dia. (mm) (mm) length (mm) n v f n v f length (mm) n v f n v f n v f n v f n v f (mm) min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min (mm) (mm) (mm) min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min 0.08 0.006 50,000 230 50,000 200 50,000 190 45,000 170 42,500 130 1 0.06 50,000 1,950 48,000 1,730 44,800 1,340 40,320 1,210 38,080 940 0.2 0.006 50,000 230 50,000 200 50,000 190 45,000 170 42,500 130 1.5 0.055 50,000 1,950 48,000 1,730 44,800 1,340 40,320 1,210 38,080 940 0.05 0.1 0.3 0.005 50,000 230 50,000 200 50,000 190 45,000 170 42,500 130 2 0.05 50,000 1,950 48,000 1,730 44,800 1,340 40,320 1,210 38,080 940 0.5 0.003 50,000 230 50,000 200 50,000 190 45,000 170 42,500 130 2.5 0.036 50,000 1,560 48,000 1,380 44,800 990 40,320 890 38,080 690 0.12 0.009 50,000 280 46,000 230 42,000 180 37,500 160 35,500 120 3 0.033 50,000 1,560 48,000 1,380 44,800 990 40,320 890 38,080 690 0.3 0.009 50,000 280 46,000 230 42,000 180 37,500 160 35,500 120 3.5 0.028 48,960 1,450 43,200 1,180 40,320 840 36,290 760 34,270 590 0.075 0.15 0.5 0.008 50,000 280 46,000 230 42,000 180 37,500 160 35,500 120 4 0.021 48,960 1,450 43,200 1,180 40,320 770 36,290 690 34,270 540 0.75 0.007 50,000 280 46,000 230 42,000 180 37,500 160 35,500 120 4.5 0.018 45,900 1,070 40,500 880 37,800 680 34,020 610 32,130 480 0.3 0.6 1 0.005 46,000 230 41,400 190 37,800 150 33,750 130 31,950 100 5 0.016 39,780 930 35,100 760 32,760 590 29,480 530 27,850 410 0.15 0.016 50,000 330 45,500 270 42,000 210 37,800 190 35,700 150 5.5 0.014 39,780 930 35,100 760 32,760 590 29,480 530 27,850 410 0.3 0.016 50,000 330 45,500 270 42,000 210 37,800 190 35,700 150 6 0.012 39,780 930 35,100 760 32,760 590 29,480 530 27,850 410 0.5 0.016 50,000 330 45,500 270 42,000 210 37,800 190 35,700 150 7 0.012 27,200 600 24,000 490 22,400 420 20,160 370 19,040 290 0.75 0.014 50,000 330 45,500 270 42,000 210 37,800 190 35,700 150 8 0.012 27,200 600 24,000 490 22,400 380 20,160 340 19,040 270 1 0.011 50,000 330 45,500 270 42,000 210 37,800 190 35,700 150 9 0.01 27,200 600 24,000 490 22,400 380 20,160 340 19,040 270 0.1 0.2 1.25 0.009 45,900 270 40,500 220 37,800 170 34,020 150 32,130 120 10 0.007 23,800 530 21,000 430 19,600 330 17,640 300 16,660 230 1.5 0.006 45,900 270 40,500 220 37,800 170 34,020 150 32,130 120 12 0.006 20,400 420 18,000 350 16,800 270 15,120 240 14,280 190 2 0.006 45,900 270 40,500 220 37,800 170 34,020 150 32,130 120 0.45 0.073 50,000 2,160 48,000 1,930 44,800 1,190 40,320 1,070 38,080 830 2.5 0.005 40,800 210 36,000 170 33,600 130 30,240 120 28,560 90 2 0.073 50,000 2,160 48,000 1,930 44,800 1,190 40,320 1,070 38,080 830 3 0.003 40,800 210 36,000 170 33,600 130 30,240 120 28,560 90 0.35 0.7 4 0.033 48,960 1,600 43,200 1,320 43,870 850 39,480 760 37,370 590 0.25 0.022 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 6 0.022 39,780 1,030 35,100 850 35,650 640 32,080 580 30,370 450 0.5 0.022 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 8 0.016 27,200 630 24,000 520 24,370 420 21,940 380 20,760 300 0.75 0.019 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 0.5 0.12 50,000 2,400 48,000 2,590 44,800 1,880 40,320 1,690 38,080 1,320 1 0.017 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 1 0.12 50,000 2,400 48,000 2,590 44,800 1,880 40,320 1,690 38,080 1,320 1.25 0.015 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 1.5 0.12 50,000 2,400 48,000 2,590 44,800 1,880 40,320 1,690 38,080 1,320 0.15 0.3 1.5 0.013 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 2 0.096 50,000 2,400 48,000 2,590 44,800 1,880 40,320 1,690 38,080 1,320 2 0.01 45,900 370 40,500 310 37,800 270 34,020 250 32,130 190 2.5 0.088 50,000 2,400 48,000 2,590 44,800 1,880 40,320 1,690 38,080 1,320 2.5 0.008 45,900 370 40,500 310 37,800 270 34,020 250 32,130 190 0.08 50,000 2,400 48,000 2,590 44,800 1,880 40,320 1,690 38,080 1,320 0.4 0.8 3 3 0.006 45,900 370 40,500 310 37,800 270 34,020 250 32,130 190 4 0.063 50,000 2,400 48,000 2,590 44,800 1,880 40,320 1,690 38,080 1,320 3.5 0.004 36,720 260 29,400 210 26,400 180 23,760 160 22,440 130 5 0.047 48,960 2,110 43,200 2,120 40,320 1,520 36,290 1,370 34,270 1,070 4 0.003 36,720 260 29,400 210 26,400 180 23,760 160 22,440 130 6 0.033 42,840 1,730 37,800 1,430 35,280 1,250 31,750 1,120 29,990 870 0.3 0.034 50,000 770 46,800 660 43,680 610 39,310 550 37,130 430 8 0.016 35,360 1,020 31,200 840 29,120 730 26,210 660 24,750 510 0.5 0.034 50,000 770 46,800 660 43,680 610 39,310 550 37,130 430 10 0.016 27,200 740 24,000 610 22,400 530 20,160 480 19,040 370 0.75 0.034 50,000 770 46,800 660 43,680 610 39,310 550 37,130 430 12 0.01 27,200 740 24,000 610 22,400 530 20,160 480 19,040 370 1 0.032 50,000 770 46,800 660 43,680 610 39,310 550 37,130 430 0.6 0.108 50,000 2,820 45,600 2,410 42,560 2,140 38,300 1,930 36,180 1,500 1.5 0.027 50,000 660 46,800 470 43,680 440 39,310 390 37,130 310 2 0.108 50,000 2,820 45,600 2,410 42,560 2,140 38,300 1,930 36,180 1,500 0.45 0.9 0.2 0.4 2 0.022 50,000 550 46,800 470 43,680 440 39,310 390 37,130 310 4 0.065 48,450 2,370 42,750 1,960 39,900 1,740 35,910 1,560 33,920 1,220 2.5 0.018 36,720 360 32,400 290 36,290 270 32,660 250 30,850 190 6 0.044 40,700 1,520 35,910 1,250 33,520 1,110 30,160 1,000 28,490 780 3 0.013 36,720 360 32,400 290 36,290 270 32,660 250 30,850 190 8 0.029 31,010 1,050 27,360 870 25,540 770 22,980 690 21,710 540 3.5 0.01 36,720 360 32,400 290 36,290 270 32,660 250 30,850 190 0.8 0.18 45,900 3,100 43,200 2,720 37,800 2,270 34,020 2,040 32,130 1,590 4 0.008 36,720 360 32,400 290 36,290 270 32,660 250 30,850 190 1.5 0.18 45,900 3,100 43,200 2,720 37,800 2,270 34,020 2,040 32,130 1,590 4.5 0.006 32,640 310 28,800 250 26,880 230 24,190 210 22,850 160 2 0.16 45,900 3,100 43,200 2,720 37,800 2,270 34,020 2,040 32,130 1,590 5 0.004 32,640 310 28,800 250 26,880 230 24,190 210 22,850 160 2.5 0.16 45,900 3,100 43,200 2,720 37,800 2,270 34,020 2,040 32,130 1,590 0.35 0.036 50,000 1,190 47,130 1,050 43,930 740 39,820 670 37,560 520 3 0.16 45,900 3,100 43,200 2,720 37,800 2,270 34,020 2,040 32,130 1,590 0.75 0.036 50,000 1,190 47,130 1,050 43,930 740 39,820 670 37,560 520 4 0.112 45,900 3,100 43,200 2,720 37,800 2,270 34,020 2,040 32,130 1,590 1 0.036 50,000 1,190 47,130 1,050 43,930 740 39,820 670 37,560 520 5 0.072 39,780 2,600 43,200 2,540 32,760 1,840 29,480 1,650 27,850 1,280 1.5 0.032 50,000 1,190 47,130 1,050 43,930 680 39,820 610 37,560 480 6 0.048 38,560 2,320 38,880 2,350 29,480 1,380 26,540 1,240 25,060 970 2 0.028 50,000 960 47,130 840 43,930 680 39,820 610 37,560 480 0.5 1 7 0.048 33,050 1,340 31,590 1,320 27,220 1,060 24,490 960 23,130 740 2.5 0.026 45,450 650 42,840 570 39,940 500 36,220 450 34,180 350 8 0.048 33,050 1,340 31,590 1,320 27,220 980 24,490 880 23,130 690 0.25 0.5 3 0.024 45,450 650 42,840 570 39,940 390 36,220 350 34,180 270 9 0.036 33,050 1,340 31,590 1,320 27,220 980 24,490 880 23,130 690 4 0.016 34,970 500 32,950 520 30,730 390 28,540 350 26,290 270 10 0.03 33,050 1,340 31,590 1,320 27,220 980 24,490 880 23,130 690 5 0.014 34,970 500 32,950 520 30,730 390 28,540 350 26,290 270 12 0.02 24,480 940 21,600 770 20,160 690 18,140 620 17,140 480 5.5 0.012 31,080 420 29,300 370 27,310 320 24,770 290 23,370 230 13 0.018 24,480 940 21,600 770 20,160 690 18,140 620 17,140 480 6 0.01 31,080 420 29,300 370 27,310 320 24,770 290 23,370 230 14 0.016 24,480 940 21,600 770 20,160 690 18,140 620 17,140 480 7 0.008 31,080 420 29,300 370 27,310 320 24,770 290 23,370 230 16 0.012 24,480 940 21,600 770 20,160 690 18,140 620 17,140 480 8 0.006 31,080 420 29,300 370 27,310 320 24,770 290 23,370 230 18 0.01 21,420 770 18,900 640 17,640 560 15,880 510 14,990 400 0.3 0.6 0.4 0.06 50,000 1,950 48,000 1,730 44,800 1,340 40,320 1,210 38,080 940 20 0.008 18,360 660 16,200 540 15,120 480 13,610 440 12,850 340 0.75 0.06 50,000 1,950 48,000 1,730 44,800 1,340 40,320 1,210 38,080 940 【注意】ご使用にあたっては、17ページの表下の項目と注意を参照してください。【Note】Upon usage, please refer to comments and notes below table on page 17. 14 15

Page15

標準切削条件表 Recommended Cut t ing Condi t ions 高能率切削条件高精度切削条件高能率切削条件高精度切削条件 High efficiency cuttiing condition High accuracy cuttiing condition 高精度切削条件は18ページを参照してください。Please refer to P.18 about high accuracy cutting conditions High efficiency cuttiing condition High accuracy cuttiing condition 高精度切削条件は18ページを参照してください。Please refer to P.18 about high accuracy cutting conditions 1 2 3 4 5 1 2 3 4 5 被削材プリハードン鋼焼入れ鋼焼入れ鋼焼入れ鋼焼入れ鋼被削材プリハードン鋼焼入れ鋼焼入れ鋼焼入れ鋼焼入れ鋼 Work material Pre-hardened steels Hardened steels Hardened steels Hardened steels Hardened steels （35～45HRC）（45～55HRC）（55～65HRC）（65～68HRC）（68～72HRC） Work material Pre-hardened steels Hardened steels Hardened steels Hardened steels Hardened steels （35～45HRC）（45～55HRC）（55～65HRC）（65～68HRC）（68～72HRC）切り込み比率 Ratio to standard depth of cut 100% 85% 80% 65% 55% 切り込み比率 Ratio to standard depth of cut 100% 85% 80% 65% 55% ボール半径RE 外径DC 首下長LU 回転数送り速度回転数送り速度回転数送り速度回転数送り速度回転数送り速度ボール半径RE 外径DC 首下長LU 回転数送り速度回転数送り速度回転数送り速度回転数送り速度回転数送り速度 Ball radius Tool dia. Under neck ap n v f n v f n v f Bal Under neck ap l radius Tool dia. (mm) (mm) length (mm) n v f n v f length (mm) n v f n v f n v f n v f n v f (mm) min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min (mm) (mm) (mm) min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min 0.08 0.006 50,000 230 50,000 200 50,000 190 45,000 170 42,500 130 1 0.06 50,000 1,950 48,000 1,730 44,800 1,340 40,320 1,210 38,080 940 0.2 0.006 50,000 230 50,000 200 50,000 190 45,000 170 42,500 130 1.5 0.055 50,000 1,950 48,000 1,730 44,800 1,340 40,320 1,210 38,080 940 0.05 0.1 0.3 0.005 50,000 230 50,000 200 50,000 190 45,000 170 42,500 130 2 0.05 50,000 1,950 48,000 1,730 44,800 1,340 40,320 1,210 38,080 940 0.5 0.003 50,000 230 50,000 200 50,000 190 45,000 170 42,500 130 2.5 0.036 50,000 1,560 48,000 1,380 44,800 990 40,320 890 38,080 690 0.12 0.009 50,000 280 46,000 230 42,000 180 37,500 160 35,500 120 3 0.033 50,000 1,560 48,000 1,380 44,800 990 40,320 890 38,080 690 0.3 0.009 50,000 280 46,000 230 42,000 180 37,500 160 35,500 120 3.5 0.028 48,960 1,450 43,200 1,180 40,320 840 36,290 760 34,270 590 0.075 0.15 0.5 0.008 50,000 280 46,000 230 42,000 180 37,500 160 35,500 120 4 0.021 48,960 1,450 43,200 1,180 40,320 770 36,290 690 34,270 540 0.75 0.007 50,000 280 46,000 230 42,000 180 37,500 160 35,500 120 4.5 0.018 45,900 1,070 40,500 880 37,800 680 34,020 610 32,130 480 0.3 0.6 1 0.005 46,000 230 41,400 190 37,800 150 33,750 130 31,950 100 5 0.016 39,780 930 35,100 760 32,760 590 29,480 530 27,850 410 0.15 0.016 50,000 330 45,500 270 42,000 210 37,800 190 35,700 150 5.5 0.014 39,780 930 35,100 760 32,760 590 29,480 530 27,850 410 0.3 0.016 50,000 330 45,500 270 42,000 210 37,800 190 35,700 150 6 0.012 39,780 930 35,100 760 32,760 590 29,480 530 27,850 410 0.5 0.016 50,000 330 45,500 270 42,000 210 37,800 190 35,700 150 7 0.012 27,200 600 24,000 490 22,400 420 20,160 370 19,040 290 0.75 0.014 50,000 330 45,500 270 42,000 210 37,800 190 35,700 150 8 0.012 27,200 600 24,000 490 22,400 380 20,160 340 19,040 270 1 0.011 50,000 330 45,500 270 42,000 210 37,800 190 35,700 150 9 0.01 27,200 600 24,000 490 22,400 380 20,160 340 19,040 270 0.1 0.2 1.25 0.009 45,900 270 40,500 220 37,800 170 34,020 150 32,130 120 10 0.007 23,800 530 21,000 430 19,600 330 17,640 300 16,660 230 1.5 0.006 45,900 270 40,500 220 37,800 170 34,020 150 32,130 120 12 0.006 20,400 420 18,000 350 16,800 270 15,120 240 14,280 190 2 0.006 45,900 270 40,500 220 37,800 170 34,020 150 32,130 120 0.45 0.073 50,000 2,160 48,000 1,930 44,800 1,190 40,320 1,070 38,080 830 2.5 0.005 40,800 210 36,000 170 33,600 130 30,240 120 28,560 90 2 0.073 50,000 2,160 48,000 1,930 44,800 1,190 40,320 1,070 38,080 830 3 0.003 40,800 210 36,000 170 33,600 130 30,240 120 28,560 90 0.35 0.7 4 0.033 48,960 1,600 43,200 1,320 43,870 850 39,480 760 37,370 590 0.25 0.022 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 6 0.022 39,780 1,030 35,100 850 35,650 640 32,080 580 30,370 450 0.5 0.022 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 8 0.016 27,200 630 24,000 520 24,370 420 21,940 380 20,760 300 0.75 0.019 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 0.5 0.12 50,000 2,400 48,000 2,590 44,800 1,880 40,320 1,690 38,080 1,320 1 0.017 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 1 0.12 50,000 2,400 48,000 2,590 44,800 1,880 40,320 1,690 38,080 1,320 1.25 0.015 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 1.5 0.12 50,000 2,400 48,000 2,590 44,800 1,880 40,320 1,690 38,080 1,320 0.15 0.3 1.5 0.013 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 2 0.096 50,000 2,400 48,000 2,590 44,800 1,880 40,320 1,690 38,080 1,320 2 0.01 45,900 370 40,500 310 37,800 270 34,020 250 32,130 190 2.5 0.088 50,000 2,400 48,000 2,590 44,800 1,880 40,320 1,690 38,080 1,320 2.5 0.008 45,900 370 40,500 310 37,800 270 34,020 250 32,130 190 0.08 50,000 2,400 48,000 2,590 44,800 1,880 40,320 1,690 38,080 1,320 0.4 0.8 3 3 0.006 45,900 370 40,500 310 37,800 270 34,020 250 32,130 190 4 0.063 50,000 2,400 48,000 2,590 44,800 1,880 40,320 1,690 38,080 1,320 3.5 0.004 36,720 260 29,400 210 26,400 180 23,760 160 22,440 130 5 0.047 48,960 2,110 43,200 2,120 40,320 1,520 36,290 1,370 34,270 1,070 4 0.003 36,720 260 29,400 210 26,400 180 23,760 160 22,440 130 6 0.033 42,840 1,730 37,800 1,430 35,280 1,250 31,750 1,120 29,990 870 0.3 0.034 50,000 770 46,800 660 43,680 610 39,310 550 37,130 430 8 0.016 35,360 1,020 31,200 840 29,120 730 26,210 660 24,750 510 0.5 0.034 50,000 770 46,800 660 43,680 610 39,310 550 37,130 430 10 0.016 27,200 740 24,000 610 22,400 530 20,160 480 19,040 370 0.75 0.034 50,000 770 46,800 660 43,680 610 39,310 550 37,130 430 12 0.01 27,200 740 24,000 610 22,400 530 20,160 480 19,040 370 1 0.032 50,000 770 46,800 660 43,680 610 39,310 550 37,130 430 0.6 0.108 50,000 2,820 45,600 2,410 42,560 2,140 38,300 1,930 36,180 1,500 1.5 0.027 50,000 660 46,800 470 43,680 440 39,310 390 37,130 310 2 0.108 50,000 2,820 45,600 2,410 42,560 2,140 38,300 1,930 36,180 1,500 0.45 0.9 0.2 0.4 2 0.022 50,000 550 46,800 470 43,680 440 39,310 390 37,130 310 4 0.065 48,450 2,370 42,750 1,960 39,900 1,740 35,910 1,560 33,920 1,220 2.5 0.018 36,720 360 32,400 290 36,290 270 32,660 250 30,850 190 6 0.044 40,700 1,520 35,910 1,250 33,520 1,110 30,160 1,000 28,490 780 3 0.013 36,720 360 32,400 290 36,290 270 32,660 250 30,850 190 8 0.029 31,010 1,050 27,360 870 25,540 770 22,980 690 21,710 540 3.5 0.01 36,720 360 32,400 290 36,290 270 32,660 250 30,850 190 0.8 0.18 45,900 3,100 43,200 2,720 37,800 2,270 34,020 2,040 32,130 1,590 4 0.008 36,720 360 32,400 290 36,290 270 32,660 250 30,850 190 1.5 0.18 45,900 3,100 43,200 2,720 37,800 2,270 34,020 2,040 32,130 1,590 4.5 0.006 32,640 310 28,800 250 26,880 230 24,190 210 22,850 160 2 0.16 45,900 3,100 43,200 2,720 37,800 2,270 34,020 2,040 32,130 1,590 5 0.004 32,640 310 28,800 250 26,880 230 24,190 210 22,850 160 2.5 0.16 45,900 3,100 43,200 2,720 37,800 2,270 34,020 2,040 32,130 1,590 0.35 0.036 50,000 1,190 47,130 1,050 43,930 740 39,820 670 37,560 520 3 0.16 45,900 3,100 43,200 2,720 37,800 2,270 34,020 2,040 32,130 1,590 0.75 0.036 50,000 1,190 47,130 1,050 43,930 740 39,820 670 37,560 520 4 0.112 45,900 3,100 43,200 2,720 37,800 2,270 34,020 2,040 32,130 1,590 1 0.036 50,000 1,190 47,130 1,050 43,930 740 39,820 670 37,560 520 5 0.072 39,780 2,600 43,200 2,540 32,760 1,840 29,480 1,650 27,850 1,280 1.5 0.032 50,000 1,190 47,130 1,050 43,930 680 39,820 610 37,560 480 6 0.048 38,560 2,320 38,880 2,350 29,480 1,380 26,540 1,240 25,060 970 2 0.028 50,000 960 47,130 840 43,930 680 39,820 610 37,560 480 0.5 1 7 0.048 33,050 1,340 31,590 1,320 27,220 1,060 24,490 960 23,130 740 2.5 0.026 45,450 650 42,840 570 39,940 500 36,220 450 34,180 350 8 0.048 33,050 1,340 31,590 1,320 27,220 980 24,490 880 23,130 690 0.25 0.5 3 0.024 45,450 650 42,840 570 39,940 390 36,220 350 34,180 270 9 0.036 33,050 1,340 31,590 1,320 27,220 980 24,490 880 23,130 690 4 0.016 34,970 500 32,950 520 30,730 390 28,540 350 26,290 270 10 0.03 33,050 1,340 31,590 1,320 27,220 980 24,490 880 23,130 690 5 0.014 34,970 500 32,950 520 30,730 390 28,540 350 26,290 270 12 0.02 24,480 940 21,600 770 20,160 690 18,140 620 17,140 480 5.5 0.012 31,080 420 29,300 370 27,310 320 24,770 290 23,370 230 13 0.018 24,480 940 21,600 770 20,160 690 18,140 620 17,140 480 6 0.01 31,080 420 29,300 370 27,310 320 24,770 290 23,370 230 14 0.016 24,480 940 21,600 770 20,160 690 18,140 620 17,140 480 7 0.008 31,080 420 29,300 370 27,310 320 24,770 290 23,370 230 16 0.012 24,480 940 21,600 770 20,160 690 18,140 620 17,140 480 8 0.006 31,080 420 29,300 370 27,310 320 24,770 290 23,370 230 18 0.01 21,420 770 18,900 640 17,640 560 15,880 510 14,990 400 0.3 0.6 0.4 0.06 50,000 1,950 48,000 1,730 44,800 1,340 40,320 1,210 38,080 940 20 0.008 18,360 660 16,200 540 15,120 480 13,610 440 12,850 340 0.75 0.06 50,000 1,950 48,000 1,730 44,800 1,340 40,320 1,210 38,080 940 【注意】ご使用にあたっては、17ページの表下の項目と注意を参照してください。【Note】Upon usage, please refer to comments and notes below table on page 17. 14 15

Page16

標準切削条件表 Recommended Cut t ing Condi t ions 高能率切削条件高精度切削条件高能率切削条件高精度切削条件 High efficiency cuttiing condition High accuracy cuttiing condition 高精度切削条件は18ページを参照してください。Please refer to P.18 about high accuracy cutting conditions High efficiency cuttiing condition High accuracy cuttiing condition 高精度切削条件は18ページを参照してください。Please refer to P.18 about high accuracy cutting conditions 1 2 3 4 5 1 2 3 4 5 被削材プリハードン鋼焼入れ鋼焼入れ鋼焼入れ鋼焼入れ鋼被削材プリハードン鋼焼入れ鋼焼入れ鋼焼入れ鋼焼入れ鋼 Work material Pre-hardened steels Hardened steels Hardened steels Hardened steels Hardened steels （35～45HRC）（45～55HRC）（55～65HRC）（65～68HRC）（68～72HRC） Work material Pre-hardened steels Hardened steels Hardened steels Hardened steels Hardened steels （35～45HRC）（45～55HRC）（55～65HRC）（65～68HRC）（68～72HRC）切り込み比率 Ratio to standard depth of cut 100% 85% 80% 65% 55% 切り込み比率 Ratio to standard depth of cut 100% 85% 80% 65% 55% ボール半径RE 外径DC 首下長LU ap 回転数送り速度回転数送り速度回転数送り速度回転数送り速度回転数送り速度ボール半径RE 外径DC 首下長LU 回転数送り速度回転数送り速度回転数送り速度回転数送り速度回転数送り速度 Ball radius Tool dia. Under neck length (mm) n v f n v f n v f n v f n v f Ball radius ool dia. Under neck ap T n v f n v f n v f n v f n v f (mm) (mm) (mm) min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min (mm) ngth ( m) (mm) le m (mm) min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min 2 0.16 42,840 2,930 37,800 2,450 35,280 2,180 31,750 1,960 29,990 1,520 6 0.4 23,590 3,800 20,810 3,090 19,430 2,530 17,480 2,280 16,610 1,820 4 0.112 42,840 2,930 37,800 2,450 35,280 2,180 31,750 1,960 29,990 1,520 10 0.272 23,590 3,800 20,810 3,090 19,430 2,530 17,480 2,280 16,610 1,820 0.55 1.1 6 0.048 33,810 1,710 29,840 1,430 27,850 1,270 25,060 1,140 23,670 890 15 0.12 18,400 2,130 16,230 2,020 15,150 1,420 13,640 1,280 12,950 1,020 1.25 2.5 8 0.048 31,210 1,310 27,540 1,100 25,700 980 23,130 880 21,850 680 20 0.096 16,980 1,640 16,230 1,450 13,990 1,090 12,590 980 11,960 790 10 0.03 31,210 1,310 27,540 1,100 25,700 980 23,130 880 21,850 680 25 0.078 16,980 1,480 14,990 1,200 13,990 980 12,590 880 11,960 710 2 0.154 39,230 2,720 36,920 2,560 32,310 1,860 29,080 1,670 27,460 1,300 30 0.044 12,580 1,150 11,100 930 10,360 770 9,320 690 8,860 550 3 0.154 39,230 2,720 36,920 2,560 32,310 1,860 29,080 1,670 27,460 1,300 6 0.48 20,400 4,100 18,000 3,400 16,800 3,020 15,120 2,720 14,360 2,180 4 0.128 39,230 2,720 36,920 2,560 32,310 1,860 29,080 1,670 27,460 1,300 8 0.48 20,400 4,100 18,000 3,400 16,800 3,020 15,120 2,720 14,360 2,180 0.6 1.2 6 0.088 39,230 2,720 36,920 2,560 32,310 1,860 29,080 1,670 27,460 1,300 10 0.336 20,400 4,100 18,000 3,400 16,800 3,020 15,120 2,720 14,360 2,180 8 0.048 31,820 2,070 30,240 2,060 26,210 1,050 23,590 940 22,280 730 13 0.252 19,040 3,060 16,800 2,540 15,680 2,260 14,110 2,030 13,410 1,630 10 0.042 29,380 1,320 27,000 1,070 24,190 870 21,770 780 20,560 610 1.5 3 16 0.252 19,040 2,760 16,800 2,290 14,560 1,890 13,100 1,700 12,450 1,360 12 0.036 29,380 1,320 25,920 1,030 24,190 870 21,770 780 20,560 610 20 0.144 15,910 1,920 14,040 1,590 12,100 1,310 10,890 1,180 10,340 940 3 0.158 33,420 2,350 29,480 1,990 27,520 1,790 24,770 1,610 23,390 1,250 25 0.096 15,910 1,920 14,040 1,590 12,100 1,310 10,890 1,180 10,340 940 8 0.088 27,850 1,810 24,570 1,530 22,930 1,380 20,640 1,240 19,490 960 30 0.096 14,690 1,770 12,960 1,470 12,100 1,310 10,890 1,180 10,340 940 0.7 1.4 12 0.042 25,700 1,250 22,680 1,060 21,170 950 19,050 860 17,990 670 35 0.064 10,880 1,240 9,600 1,030 10,750 1,100 9,680 990 9,190 790 16 0.028 19,040 870 16,800 740 15,680 670 14,110 600 13,330 470 10 0.328 15,190 2,750 13,410 2,240 12,510 1,830 11,260 1,650 10,700 1,320 2 0.192 35,700 3,210 31,500 2,550 29,400 2,210 26,460 1,990 24,990 1,540 15 0.288 15,190 2,750 13,410 2,240 12,510 1,830 11,260 1,650 10,700 1,320 2.5 0.192 35,700 3,210 31,500 2,550 29,400 2,210 26,460 1,990 24,990 1,540 1.75 3.5 25 0.168 12,620 1,710 11,140 1,390 10,400 1,140 9,360 1,030 8,890 820 3 0.192 35,700 3,210 31,500 2,550 29,400 2,210 26,460 1,990 24,990 1,540 35 0.072 12,620 1,710 11,140 1,390 10,400 1,140 9,360 1,030 8,890 820 4 0.16 35,700 3,210 31,500 2,550 29,400 2,210 26,460 1,990 24,990 1,540 45 0.072 9,350 1,200 8,250 980 7,700 800 6,930 720 6,580 580 5 0.16 35,700 3,210 31,500 2,550 29,400 2,210 26,460 1,990 24,990 1,540 8 0.48 14,660 3,960 12,940 3,300 12,080 2,900 10,870 2,610 10,320 2,090 6 0.16 35,700 3,210 31,500 2,550 29,400 2,210 26,460 1,990 24,990 1,540 10 0.48 14,660 3,960 12,940 3,300 12,080 2,900 10,870 2,610 10,320 2,090 0.75 1.5 8 0.072 27,850 1,810 24,570 1,430 22,930 1,240 20,640 1,120 19,490 870 12 0.384 14,660 3,960 12,940 3,300 12,080 2,900 10,870 2,610 10,320 2,090 10 0.072 25,700 1,670 22,680 1,320 21,170 1,140 19,050 1,030 17,990 800 13 0.384 14,660 3,960 12,940 3,300 12,080 2,900 10,870 2,610 10,320 2,090 12 0.072 25,700 1,390 22,680 1,100 21,170 950 19,050 860 17,990 670 16 0.336 14,660 3,960 12,940 3,300 12,080 2,900 10,870 2,610 10,320 2,090 14 0.06 22,850 1,170 20,160 930 18,820 800 16,930 720 15,990 560 20 0.336 12,710 2,750 11,210 2,290 10,470 2,010 9,420 1,810 8,950 1,450 2 4 16 0.03 19,040 970 16,800 770 15,680 670 14,110 600 13,330 470 25 0.192 11,440 2,220 10,090 2,160 9,420 1,630 8,480 1,460 8,050 1,170 18 0.03 19,040 970 16,800 770 15,680 670 14,110 600 13,330 470 30 0.128 10,560 1,710 9,320 1,430 8,690 1,250 7,820 1,130 7,430 900 20 0.03 19,040 970 16,800 770 15,680 670 14,110 600 13,330 470 35 0.08 10,560 1,710 9,320 1,430 8,690 1,250 7,820 1,130 7,430 900 4 0.23 33,110 3,340 29,210 2,850 25,320 2,130 22,780 1,920 21,520 1,490 40 0.08 10,560 1,710 9,320 1,430 8,690 1,250 7,820 1,130 7,430 900 8 0.176 30,940 2,490 27,300 2,130 23,660 1,590 21,290 1,430 20,110 1,110 45 0.08 7,820 1,200 6,900 1,000 6,440 880 5,800 790 5,510 630 0.8 1.6 12 0.078 27,850 2,180 24,570 1,860 21,290 1,290 19,170 1,160 18,100 900 50 0.08 7,820 1,200 6,900 1,000 6,440 880 5,800 790 5,510 630 16 0.048 23,870 1,330 21,060 1,140 19,660 990 17,690 890 16,710 690 10 0.584 10,710 3,210 9,450 2,840 8,820 2,380 7,940 2,140 7,540 1,710 20 0.032 17,680 930 15,600 800 14,560 690 13,100 620 12,380 490 20 0.42 10,710 3,210 9,450 2,840 8,820 2,380 7,940 2,140 7,540 1,710 4 0.29 28,730 2,410 25,350 2,010 23,660 1,700 21,290 1,530 20,110 1,190 2.5 5 25 0.42 9,950 2,980 8,780 2,630 8,190 2,210 7,370 1,990 7,000 1,590 8 0.208 28,730 2,410 25,350 2,010 23,660 1,700 21,290 1,530 20,110 1,190 30 0.24 8,950 2,690 7,900 2,370 7,370 1,990 6,630 1,790 6,300 1,430 0.9 1.8 12 0.084 23,870 1,500 21,060 1,250 19,660 1,060 17,690 960 16,710 740 40 0.16 8,260 1,490 7,290 1,310 6,800 1,100 6,120 990 5,820 790 16 0.054 23,870 1,500 21,060 1,250 19,660 1,060 17,690 960 16,710 740 12 0.48 11,480 4,250 10,130 3,460 9,450 2,840 8,510 2,550 8,080 2,040 20 0.036 17,680 1,050 15,600 880 14,560 740 13,100 670 12,380 520 3 20 0.4 10,840 3,730 9,560 3,030 8,930 2,490 8,030 2,240 7,630 1,790 6 2.5 0.32 26,780 3,620 23,630 3,050 22,050 2,650 19,850 2,380 18,740 1,850 30 0.336 8,840 2,120 7,800 2,030 7,280 1,570 6,550 1,410 6,220 1,130 3 0.32 26,780 3,620 23,630 3,050 22,050 2,650 19,850 2,380 18,740 1,850 50 0.12 7,340 1,590 6,480 1,400 6,050 1,180 5,440 1,060 5,170 850 4 0.32 26,780 3,620 23,630 3,050 22,050 2,650 19,850 2,380 18,740 1,850 4 8 24 0.5 8,750 3,420 7,550 2,600 7,100 2,450 6,390 1,850 5,750 1,270 5 0.32 26,780 3,620 23,630 3,050 22,050 2,650 19,850 2,380 18,740 1,850 5 10 30 0.6 7,000 3,000 6,050 2,250 5,680 2,130 5,110 1,610 4,600 1,030 6 0.32 26,780 3,210 23,630 2,690 22,050 2,380 19,850 2,140 18,740 1,670 6 12 36 0.8 5,850 2,600 5,050 1,980 4,720 1,840 4,250 1,440 3,820 880 8 0.224 26,780 3,210 23,630 2,690 22,050 2,380 19,850 2,140 18,740 1,670 ※（１）apは被削材グル－プ1での目安を示しています。その他のグループの場合は、上表の切込み比率を目安に調整してください。 10 0.168 24,990 2,700 22,050 2,250 19,110 1,470 17,200 1,320 16,240 1,030 ※（２）リブ加工や止まり溝など、切りくずがつまりやすい切削の場合、切込み設定は基本切込みに切込み比率をかけて算出した切込み量を、 12 0.096 22,490 2,430 19,850 2,050 17,200 1,320 15,480 1,190 14,620 930 　　　さらにその80％まで小さくして使用してください。 ※（３）aeの設定はap×切込み比率×3～5倍を目安に調整してください。仕上げ加工を行う場合、理論カスプハイトを計算し設定してください。 1 2 13 0.096 22,490 2,430 19,850 2,020 15,880 1,020 14,290 920 13,500 710 14 0.096 22,490 2,110 18,430 1,630 15,880 1,020 14,290 920 13,500 710 ※(1) ap is shown as the criteria for Group 1 workpieces. For other groups, adjust the cutting depth according to the cutting depth factors in the above table. ※(2) When performing cutting where cutting chips may cause clogging, such as for rib cutting, blind grooves, etc., cutting depth setting should be set by multiplying a cutting 16 0.096 20,890 1,350 18,430 1,470 15,880 910 14,290 820 13,500 640 　depth factor to calculate the cutting depth amount, and this amount should then be reduced to 80% of the calculated value. 18 0.072 19,280 1,250 18,430 1,350 15,880 910 14,290 820 13,500 640 ※(3) Adjust by setting ae to (3 to 5)×(ap)×(cutting depth ratio). When performing finishing processing, calculate the theoretical cusp height and set accordingly. 20 0.06 19,280 1,250 18,430 1,130 15,880 910 14,290 820 13,500 640 【切込み設定例】EPDBEH2020-10-TH3の工具で焼入れ鋼（50HRC）をリブ溝等高線切削する場合、 22 0.04 15,170 930 13,390 770 14,990 820 13,500 730 12,750 570 切込み=0.168（ap）×0.85（焼入れ鋼グループ2の切込み比率）×0.8（閉鎖域の切削）=0.11mm 25 0.04 14,280 870 12,600 730 14,110 770 12,700 690 12,000 540 Cutting depth setting example: When cutting rib groove contours in hardened steel (50HRC) using an EPDBEH2020-10-TH3 tool: Cutting depth = 0.168 (ap) × 0.85 (cutting depth factor for Group 2 hardened steel) × 0.8 (for closed-area cutting) = 0.11mm 30 0.024 14,280 870 12,600 730 14,110 770 12,700 690 12,000 540 35 0.02 12,500 720 11,030 600 10,290 530 9,260 470 8,750 370 【注意】①基本的にはDry（エアーブロー）切削を推奨しますが、被削材、加工形状に合わせて、適切なクーラントを使用してください。②この標準切削条件表は切削条件の目安を示すものです。実際の加工では加工形状、目的、使用機械等により条件を調整してください。 40 0.018 10,710 620 9,450 510 8,820 450 7,940 410 7,500 320 ③機械の回転数が足りない場合は、回転数と送り速度を同じ比率で下げてください。【Note】 ① Although basically dry (air blow) cutting is recommended, please use appropriate coolant according to the work material and machining shape. ② These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type. ③ If the rpm of the machine is low, lower the feed rate also to put the rpm and feed rate in the same ratio. 16 17

Page17

標準切削条件表 Recommended Cut t ing Condi t ions 高能率切削条件高精度切削条件高能率切削条件高精度切削条件 High efficiency cuttiing condition High accuracy cuttiing condition 高精度切削条件は18ページを参照してください。Please refer to P.18 about high accuracy cutting conditions High efficiency cuttiing condition High accuracy cuttiing condition 高精度切削条件は18ページを参照してください。Please refer to P.18 about high accuracy cutting conditions 1 2 3 4 5 1 2 3 4 5 被削材プリハードン鋼焼入れ鋼焼入れ鋼焼入れ鋼焼入れ鋼被削材プリハードン鋼焼入れ鋼焼入れ鋼焼入れ鋼焼入れ鋼 Work material Pre-hardened steels Hardened steels Hardened steels Hardened steels Hardened steels （35～45HRC）（45～55HRC）（55～65HRC）（65～68HRC）（68～72HRC） Work material Pre-hardened steels Hardened steels Hardened steels Hardened steels Hardened steels （35～45HRC）（45～55HRC）（55～65HRC）（65～68HRC）（68～72HRC）切り込み比率 Ratio to standard depth of cut 100% 85% 80% 65% 55% 切り込み比率 Ratio to standard depth of cut 100% 85% 80% 65% 55% ボール半径RE 外径DC 首下長LU ap 回転数送り速度回転数送り速度回転数送り速度回転数送り速度回転数送り速度ボール半径RE 外径DC 首下長LU 回転数送り速度回転数送り速度回転数送り速度回転数送り速度回転数送り速度 Ball radius Tool dia. Under neck length (mm) n v f n v f n v f n v f n v f Ball radius ool dia. Under neck ap T n v f n v f n v f n v f n v f (mm) (mm) (mm) min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min (mm) ngth ( m) (mm) le m (mm) min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min 2 0.16 42,840 2,930 37,800 2,450 35,280 2,180 31,750 1,960 29,990 1,520 6 0.4 23,590 3,800 20,810 3,090 19,430 2,530 17,480 2,280 16,610 1,820 4 0.112 42,840 2,930 37,800 2,450 35,280 2,180 31,750 1,960 29,990 1,520 10 0.272 23,590 3,800 20,810 3,090 19,430 2,530 17,480 2,280 16,610 1,820 0.55 1.1 6 0.048 33,810 1,710 29,840 1,430 27,850 1,270 25,060 1,140 23,670 890 15 0.12 18,400 2,130 16,230 2,020 15,150 1,420 13,640 1,280 12,950 1,020 1.25 2.5 8 0.048 31,210 1,310 27,540 1,100 25,700 980 23,130 880 21,850 680 20 0.096 16,980 1,640 16,230 1,450 13,990 1,090 12,590 980 11,960 790 10 0.03 31,210 1,310 27,540 1,100 25,700 980 23,130 880 21,850 680 25 0.078 16,980 1,480 14,990 1,200 13,990 980 12,590 880 11,960 710 2 0.154 39,230 2,720 36,920 2,560 32,310 1,860 29,080 1,670 27,460 1,300 30 0.044 12,580 1,150 11,100 930 10,360 770 9,320 690 8,860 550 3 0.154 39,230 2,720 36,920 2,560 32,310 1,860 29,080 1,670 27,460 1,300 6 0.48 20,400 4,100 18,000 3,400 16,800 3,020 15,120 2,720 14,360 2,180 4 0.128 39,230 2,720 36,920 2,560 32,310 1,860 29,080 1,670 27,460 1,300 8 0.48 20,400 4,100 18,000 3,400 16,800 3,020 15,120 2,720 14,360 2,180 0.6 1.2 6 0.088 39,230 2,720 36,920 2,560 32,310 1,860 29,080 1,670 27,460 1,300 10 0.336 20,400 4,100 18,000 3,400 16,800 3,020 15,120 2,720 14,360 2,180 8 0.048 31,820 2,070 30,240 2,060 26,210 1,050 23,590 940 22,280 730 13 0.252 19,040 3,060 16,800 2,540 15,680 2,260 14,110 2,030 13,410 1,630 10 0.042 29,380 1,320 27,000 1,070 24,190 870 21,770 780 20,560 610 1.5 3 16 0.252 19,040 2,760 16,800 2,290 14,560 1,890 13,100 1,700 12,450 1,360 12 0.036 29,380 1,320 25,920 1,030 24,190 870 21,770 780 20,560 610 20 0.144 15,910 1,920 14,040 1,590 12,100 1,310 10,890 1,180 10,340 940 3 0.158 33,420 2,350 29,480 1,990 27,520 1,790 24,770 1,610 23,390 1,250 25 0.096 15,910 1,920 14,040 1,590 12,100 1,310 10,890 1,180 10,340 940 8 0.088 27,850 1,810 24,570 1,530 22,930 1,380 20,640 1,240 19,490 960 30 0.096 14,690 1,770 12,960 1,470 12,100 1,310 10,890 1,180 10,340 940 0.7 1.4 12 0.042 25,700 1,250 22,680 1,060 21,170 950 19,050 860 17,990 670 35 0.064 10,880 1,240 9,600 1,030 10,750 1,100 9,680 990 9,190 790 16 0.028 19,040 870 16,800 740 15,680 670 14,110 600 13,330 470 10 0.328 15,190 2,750 13,410 2,240 12,510 1,830 11,260 1,650 10,700 1,320 2 0.192 35,700 3,210 31,500 2,550 29,400 2,210 26,460 1,990 24,990 1,540 15 0.288 15,190 2,750 13,410 2,240 12,510 1,830 11,260 1,650 10,700 1,320 2.5 0.192 35,700 3,210 31,500 2,550 29,400 2,210 26,460 1,990 24,990 1,540 1.75 3.5 25 0.168 12,620 1,710 11,140 1,390 10,400 1,140 9,360 1,030 8,890 820 3 0.192 35,700 3,210 31,500 2,550 29,400 2,210 26,460 1,990 24,990 1,540 35 0.072 12,620 1,710 11,140 1,390 10,400 1,140 9,360 1,030 8,890 820 4 0.16 35,700 3,210 31,500 2,550 29,400 2,210 26,460 1,990 24,990 1,540 45 0.072 9,350 1,200 8,250 980 7,700 800 6,930 720 6,580 580 5 0.16 35,700 3,210 31,500 2,550 29,400 2,210 26,460 1,990 24,990 1,540 8 0.48 14,660 3,960 12,940 3,300 12,080 2,900 10,870 2,610 10,320 2,090 6 0.16 35,700 3,210 31,500 2,550 29,400 2,210 26,460 1,990 24,990 1,540 10 0.48 14,660 3,960 12,940 3,300 12,080 2,900 10,870 2,610 10,320 2,090 0.75 1.5 8 0.072 27,850 1,810 24,570 1,430 22,930 1,240 20,640 1,120 19,490 870 12 0.384 14,660 3,960 12,940 3,300 12,080 2,900 10,870 2,610 10,320 2,090 10 0.072 25,700 1,670 22,680 1,320 21,170 1,140 19,050 1,030 17,990 800 13 0.384 14,660 3,960 12,940 3,300 12,080 2,900 10,870 2,610 10,320 2,090 12 0.072 25,700 1,390 22,680 1,100 21,170 950 19,050 860 17,990 670 16 0.336 14,660 3,960 12,940 3,300 12,080 2,900 10,870 2,610 10,320 2,090 14 0.06 22,850 1,170 20,160 930 18,820 800 16,930 720 15,990 560 20 0.336 12,710 2,750 11,210 2,290 10,470 2,010 9,420 1,810 8,950 1,450 2 4 16 0.03 19,040 970 16,800 770 15,680 670 14,110 600 13,330 470 25 0.192 11,440 2,220 10,090 2,160 9,420 1,630 8,480 1,460 8,050 1,170 18 0.03 19,040 970 16,800 770 15,680 670 14,110 600 13,330 470 30 0.128 10,560 1,710 9,320 1,430 8,690 1,250 7,820 1,130 7,430 900 20 0.03 19,040 970 16,800 770 15,680 670 14,110 600 13,330 470 35 0.08 10,560 1,710 9,320 1,430 8,690 1,250 7,820 1,130 7,430 900 4 0.23 33,110 3,340 29,210 2,850 25,320 2,130 22,780 1,920 21,520 1,490 40 0.08 10,560 1,710 9,320 1,430 8,690 1,250 7,820 1,130 7,430 900 8 0.176 30,940 2,490 27,300 2,130 23,660 1,590 21,290 1,430 20,110 1,110 45 0.08 7,820 1,200 6,900 1,000 6,440 880 5,800 790 5,510 630 0.8 1.6 12 0.078 27,850 2,180 24,570 1,860 21,290 1,290 19,170 1,160 18,100 900 50 0.08 7,820 1,200 6,900 1,000 6,440 880 5,800 790 5,510 630 16 0.048 23,870 1,330 21,060 1,140 19,660 990 17,690 890 16,710 690 10 0.584 10,710 3,210 9,450 2,840 8,820 2,380 7,940 2,140 7,540 1,710 20 0.032 17,680 930 15,600 800 14,560 690 13,100 620 12,380 490 20 0.42 10,710 3,210 9,450 2,840 8,820 2,380 7,940 2,140 7,540 1,710 4 0.29 28,730 2,410 25,350 2,010 23,660 1,700 21,290 1,530 20,110 1,190 2.5 5 25 0.42 9,950 2,980 8,780 2,630 8,190 2,210 7,370 1,990 7,000 1,590 8 0.208 28,730 2,410 25,350 2,010 23,660 1,700 21,290 1,530 20,110 1,190 30 0.24 8,950 2,690 7,900 2,370 7,370 1,990 6,630 1,790 6,300 1,430 0.9 1.8 12 0.084 23,870 1,500 21,060 1,250 19,660 1,060 17,690 960 16,710 740 40 0.16 8,260 1,490 7,290 1,310 6,800 1,100 6,120 990 5,820 790 16 0.054 23,870 1,500 21,060 1,250 19,660 1,060 17,690 960 16,710 740 12 0.48 11,480 4,250 10,130 3,460 9,450 2,840 8,510 2,550 8,080 2,040 20 0.036 17,680 1,050 15,600 880 14,560 740 13,100 670 12,380 520 3 20 0.4 10,840 3,730 9,560 3,030 8,930 2,490 8,030 2,240 7,630 1,790 6 2.5 0.32 26,780 3,620 23,630 3,050 22,050 2,650 19,850 2,380 18,740 1,850 30 0.336 8,840 2,120 7,800 2,030 7,280 1,570 6,550 1,410 6,220 1,130 3 0.32 26,780 3,620 23,630 3,050 22,050 2,650 19,850 2,380 18,740 1,850 50 0.12 7,340 1,590 6,480 1,400 6,050 1,180 5,440 1,060 5,170 850 4 0.32 26,780 3,620 23,630 3,050 22,050 2,650 19,850 2,380 18,740 1,850 4 8 24 0.5 8,750 3,420 7,550 2,600 7,100 2,450 6,390 1,850 5,750 1,270 5 0.32 26,780 3,620 23,630 3,050 22,050 2,650 19,850 2,380 18,740 1,850 5 10 30 0.6 7,000 3,000 6,050 2,250 5,680 2,130 5,110 1,610 4,600 1,030 6 0.32 26,780 3,210 23,630 2,690 22,050 2,380 19,850 2,140 18,740 1,670 6 12 36 0.8 5,850 2,600 5,050 1,980 4,720 1,840 4,250 1,440 3,820 880 8 0.224 26,780 3,210 23,630 2,690 22,050 2,380 19,850 2,140 18,740 1,670 ※（１）apは被削材グル－プ1での目安を示しています。その他のグループの場合は、上表の切込み比率を目安に調整してください。 10 0.168 24,990 2,700 22,050 2,250 19,110 1,470 17,200 1,320 16,240 1,030 ※（２）リブ加工や止まり溝など、切りくずがつまりやすい切削の場合、切込み設定は基本切込みに切込み比率をかけて算出した切込み量を、 12 0.096 22,490 2,430 19,850 2,050 17,200 1,320 15,480 1,190 14,620 930 　　　さらにその80％まで小さくして使用してください。 ※（３）aeの設定はap×切込み比率×3～5倍を目安に調整してください。仕上げ加工を行う場合、理論カスプハイトを計算し設定してください。 1 2 13 0.096 22,490 2,430 19,850 2,020 15,880 1,020 14,290 920 13,500 710 14 0.096 22,490 2,110 18,430 1,630 15,880 1,020 14,290 920 13,500 710 ※(1) ap is shown as the criteria for Group 1 workpieces. For other groups, adjust the cutting depth according to the cutting depth factors in the above table. ※(2) When performing cutting where cutting chips may cause clogging, such as for rib cutting, blind grooves, etc., cutting depth setting should be set by multiplying a cutting 16 0.096 20,890 1,350 18,430 1,470 15,880 910 14,290 820 13,500 640 　depth factor to calculate the cutting depth amount, and this amount should then be reduced to 80% of the calculated value. 18 0.072 19,280 1,250 18,430 1,350 15,880 910 14,290 820 13,500 640 ※(3) Adjust by setting ae to (3 to 5)×(ap)×(cutting depth ratio). When performing finishing processing, calculate the theoretical cusp height and set accordingly. 20 0.06 19,280 1,250 18,430 1,130 15,880 910 14,290 820 13,500 640 【切込み設定例】EPDBEH2020-10-TH3の工具で焼入れ鋼（50HRC）をリブ溝等高線切削する場合、 22 0.04 15,170 930 13,390 770 14,990 820 13,500 730 12,750 570 切込み=0.168（ap）×0.85（焼入れ鋼グループ2の切込み比率）×0.8（閉鎖域の切削）=0.11mm 25 0.04 14,280 870 12,600 730 14,110 770 12,700 690 12,000 540 Cutting depth setting example: When cutting rib groove contours in hardened steel (50HRC) using an EPDBEH2020-10-TH3 tool: Cutting depth = 0.168 (ap) × 0.85 (cutting depth factor for Group 2 hardened steel) × 0.8 (for closed-area cutting) = 0.11mm 30 0.024 14,280 870 12,600 730 14,110 770 12,700 690 12,000 540 35 0.02 12,500 720 11,030 600 10,290 530 9,260 470 8,750 370 【注意】①基本的にはDry（エアーブロー）切削を推奨しますが、被削材、加工形状に合わせて、適切なクーラントを使用してください。②この標準切削条件表は切削条件の目安を示すものです。実際の加工では加工形状、目的、使用機械等により条件を調整してください。 40 0.018 10,710 620 9,450 510 8,820 450 7,940 410 7,500 320 ③機械の回転数が足りない場合は、回転数と送り速度を同じ比率で下げてください。【Note】 ① Although basically dry (air blow) cutting is recommended, please use appropriate coolant according to the work material and machining shape. ② These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type. ③ If the rpm of the machine is low, lower the feed rate also to put the rpm and feed rate in the same ratio. 16 17

Page18

標準切削条件表 Recommended Cut t ing Condi t ions 高能率切削条件高精度切削条件高能率切削条件高精度切削条件 High efficiency cuttiing condition High accuracy cuttiing condition 高能率切削条件は14ページを参照してください。Please refer to P.14 about high efficiency cutting conditions High efficiency cuttiing condition High accuracy cuttiing condition 高能率切削条件は14ページを参照してください。Please refer to P.14 about high efficiency cutting conditions 1 2 3 4 5 1 2 3 4 5 被削材プリハードン鋼焼入れ鋼焼入れ鋼焼入れ鋼焼入れ鋼被削材プリハードン鋼焼入れ鋼焼入れ鋼焼入れ鋼焼入れ鋼 Work material Pre-hardened steels Hardened steels Hardened steels Hardened steels Hardened steels （35～45HRC）（45～55HRC）（55～65HRC）（65～68HRC）（68～72HRC） Work material Pre-hardened steels Hardened steels Hardened steels Hardened steels Hardened steels （35～45HRC）（45～55HRC）（55～65HRC）（65～68HRC）（68～72HRC）切り込み比率 Ratio to standard depth of cut 100% 85% 80% 65% 55% 切り込み比率 Ratio to standard depth of cut 100% 85% 80% 65% 55% ボール半径RE 外径DC 首下長LU 回転数送り速度回転数送り速度回転数送り速度回転数送り速度回転数送り速度ボール半径RE 外径DC 首下長LU 回転数送り速度回転数送り速度回 Ball radius Tool dia. Under neck ap Under neck ap 転数送り速度回転数送り速度回転数送り速度 length (mm) n v f n v f n v f n v f n v f Ball radius Tool dia. length (mm) n v f n v f n v f n v f n v f (mm) (mm) (mm) min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min (mm) (mm) (mm) min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min 0.08 0.003 50,000 230 50,000 200 50,000 190 45,000 170 42,500 130 1 0.04 34,000 880 30,000 720 28,000 560 25,200 500 23,800 390 0.2 0.003 50,000 230 50,000 200 50,000 190 45,000 170 42,500 130 1.5 0.038 34,000 880 30,000 720 28,000 560 25,200 500 23,800 390 0.05 0.1 0.3 0.002 50,000 230 50,000 200 50,000 190 45,000 170 42,500 130 2 0.034 34,000 880 30,000 720 28,000 560 25,200 500 23,800 390 0.5 0.002 50,000 230 50,000 200 50,000 190 45,000 170 42,500 130 2.5 0.03 34,000 880 30,000 720 28,000 560 25,200 500 23,800 390 0.12 0.007 50,000 280 46,000 230 42,000 180 37,500 160 35,500 120 3 0.027 34,000 880 30,000 720 28,000 560 25,200 500 23,800 390 0.3 0.007 50,000 280 46,000 230 42,000 180 37,500 160 35,500 120 3.5 0.023 30,600 760 27,000 620 25,200 480 22,680 430 21,420 340 0.075 0.15 0.5 0.006 50,000 280 46,000 230 42,000 180 37,500 160 35,500 120 4 0.019 30,600 760 27,000 620 25,200 480 22,680 430 21,420 340 0.75 0.005 50,000 280 46,000 230 42,000 180 37,500 160 35,500 120 4.5 0.018 30,600 720 27,000 580 25,200 450 22,680 410 21,420 320 0.3 0.6 1 0.003 46,000 230 41,400 190 37,800 150 33,750 130 31,950 100 5 0.016 30,600 720 27,000 580 25,200 450 22,680 410 21,420 320 0.15 0.012 50,000 330 45,500 270 42,000 210 37,800 190 35,700 150 5.5 0.014 30,600 720 27,000 580 25,200 450 22,680 410 21,420 320 0.3 0.012 50,000 330 45,500 270 42,000 210 37,800 190 35,700 150 6 0.012 30,600 720 27,000 580 25,200 450 22,680 410 21,420 320 0.5 0.012 50,000 330 45,500 270 42,000 210 37,800 190 35,700 150 7 0.006 27,200 600 24,000 490 22,400 380 20,160 340 19,040 270 0.75 0.01 50,000 330 45,500 270 42,000 210 37,800 190 35,700 150 8 0.006 27,200 600 24,000 490 22,400 380 20,160 340 19,040 270 1 0.009 50,000 330 45,500 270 42,000 210 37,800 190 35,700 150 9 0.005 27,200 600 24,000 490 22,400 380 20,160 340 19,040 270 0.1 0.2 1.25 0.006 45,900 270 40,500 220 37,800 170 34,020 150 32,130 120 10 0.004 23,800 530 21,000 430 19,600 330 17,640 300 16,660 230 1.5 0.006 45,900 270 40,500 220 37,800 170 34,020 150 32,130 120 12 0.003 20,400 420 18,000 350 16,800 270 15,120 240 14,280 190 2 0.005 45,900 270 40,500 220 37,800 170 34,020 150 32,130 120 0.45 0.049 34,000 980 30,000 810 28,000 660 25,200 590 23,800 460 2.5 0.004 40,800 210 36,000 170 33,600 130 30,240 120 28,560 90 2 0.049 34,000 980 30,000 810 28,000 660 25,200 590 23,800 460 3 0.002 40,800 210 36,000 170 33,600 130 30,240 120 28,560 90 0.35 0.7 4 0.027 30,600 840 27,000 690 25,200 560 22,680 510 21,420 400 0.25 0.016 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 6 0.022 30,600 790 27,000 650 25,200 540 22,680 480 21,420 370 0.5 0.016 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 8 0.008 27,200 630 24,000 520 22,400 420 20,160 380 19,040 300 0.75 0.014 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 0.5 0.08 34,000 1,090 30,000 900 28,000 780 25,200 710 23,800 550 1 0.013 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 1 0.08 34,000 1,090 30,000 900 28,000 780 25,200 710 23,800 550 1.25 0.011 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 1.5 0.08 34,000 1,090 30,000 900 28,000 780 25,200 710 23,800 550 0.15 0.3 1.5 0.01 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 2 0.064 34,000 1,090 30,000 900 28,000 780 25,200 710 23,800 550 2 0.007 45,900 370 40,500 310 37,800 270 34,020 250 32,130 190 2.5 0.06 34,000 1,090 30,000 900 28,000 780 25,200 710 23,800 550 2.5 0.006 45,900 370 40,500 310 37,800 270 34,020 250 32,130 190 0.4 0.8 3 0.055 34,000 1,090 30,000 900 28,000 780 25,200 710 23,800 550 3 0.005 45,900 370 40,500 310 37,800 270 34,020 250 32,130 190 4 0.045 34,000 1,090 30,000 900 28,000 780 25,200 710 23,800 550 3.5 0.003 36,720 260 29,400 210 26,400 180 23,760 160 22,440 130 5 0.036 30,600 880 27,000 730 25,200 640 22,680 570 21,420 450 4 0.002 36,720 260 29,400 210 26,400 180 23,760 160 22,440 130 6 0.026 30,600 880 27,000 730 25,200 640 22,680 570 21,420 450 0.3 0.034 40,800 450 36,000 360 33,600 340 30,240 300 28,560 240 8 0.016 27,200 780 24,000 650 22,400 560 20,160 510 19,040 400 0.5 0.034 40,800 450 36,000 360 33,600 340 30,240 300 28,560 240 10 0.008 27,200 740 24,000 610 22,400 530 20,160 480 19,040 370 0.75 0.034 40,800 450 36,000 360 33,600 340 30,240 300 28,560 240 12 0.006 27,200 740 24,000 610 22,400 530 20,160 480 19,040 370 1 0.032 40,800 450 36,000 360 33,600 340 30,240 300 28,560 240 0.6 0.072 32,300 1,220 28,500 1,000 26,600 890 23,940 800 22,610 620 1.5 0.027 40,800 450 36,000 360 33,600 340 30,240 300 28,560 240 2 0.072 32,300 1,220 28,500 1,000 26,600 890 23,940 800 22,610 620 0.2 0.4 2 0.022 40,800 450 36,000 360 33,600 340 30,240 300 28,560 240 0.45 0.9 4 0.046 32,300 1,220 28,500 1,000 26,600 890 23,940 800 22,610 620 2.5 0.013 36,720 360 32,400 290 30,240 270 27,220 250 25,700 190 6 0.034 29,070 980 25,650 810 23,940 720 21,550 650 20,350 510 3 0.009 36,720 360 32,400 290 30,240 270 27,220 250 25,700 190 8 0.024 25,840 880 22,800 720 21,280 640 19,150 580 18,090 450 3.5 0.006 36,720 360 32,400 290 30,240 270 27,220 250 25,700 190 0.8 0.09 30,600 1,380 27,000 1,130 25,200 1,010 22,680 910 21,420 710 4 0.004 36,720 360 32,400 290 30,240 270 27,220 250 25,700 190 1.5 0.09 30,600 1,380 27,000 1,130 25,200 1,010 22,680 910 21,420 710 4.5 0.003 32,640 310 28,800 250 26,880 230 24,190 210 22,850 160 2 0.08 30,600 1,380 27,000 1,130 25,200 1,010 22,680 910 21,420 710 5 0.002 32,640 310 28,800 250 26,880 230 24,190 210 22,850 160 2.5 0.08 30,600 1,380 27,000 1,130 25,200 1,010 22,680 910 21,420 710 0.35 0.036 34,000 610 30,000 540 28,000 480 25,200 430 23,800 330 3 0.08 30,600 1,380 27,000 1,130 25,200 1,010 22,680 910 21,420 710 0.75 0.036 34,000 610 30,000 540 28,000 480 25,200 430 23,800 330 4 0.056 30,600 1,380 27,000 1,130 25,200 1,010 22,680 910 21,420 710 1 0.036 34,000 610 30,000 540 28,000 480 25,200 430 23,800 330 5 0.048 30,600 1,380 27,000 1,130 25,200 1,010 22,680 910 21,420 710 1.5 0.032 34,000 610 30,000 540 28,000 480 25,200 430 23,800 330 6 0.032 27,540 1,120 24,300 920 22,680 820 20,410 730 19,280 570 2 0.028 34,000 610 30,000 540 28,000 480 25,200 430 23,800 330 0.5 1 7 0.032 27,540 1,120 24,300 920 22,680 820 20,410 730 19,280 570 2.5 0.026 30,600 500 27,000 440 25,200 390 22,680 350 21,420 270 8 0.032 27,540 1,120 24,300 920 22,680 820 20,410 730 19,280 570 0.25 0.5 3 0.024 30,600 500 27,000 440 25,200 390 22,680 350 21,420 270 9 0.024 27,540 1,120 24,300 920 22,680 820 20,410 730 19,280 570 4 0.016 30,600 500 27,000 440 25,200 390 22,680 350 21,420 270 10 0.02 27,540 1,120 24,300 920 22,680 820 20,410 730 19,280 570 5 0.014 30,600 500 27,000 440 25,200 390 22,680 350 21,420 270 12 0.01 24,480 940 21,600 770 20,160 690 18,140 620 17,140 480 5.5 0.006 27,200 420 24,000 370 22,400 320 20,160 290 19,040 230 13 0.009 24,480 940 21,600 770 20,160 690 18,140 620 17,140 480 6 0.005 27,200 420 24,000 370 22,400 320 20,160 290 19,040 230 14 0.008 24,480 940 21,600 770 20,160 690 18,140 620 17,140 480 7 0.004 27,200 420 24,000 370 22,400 320 20,160 290 19,040 230 16 0.006 24,480 940 21,600 770 20,160 690 18,140 620 17,140 480 8 0.003 27,200 420 24,000 370 22,400 320 20,160 290 19,040 230 18 0.005 21,420 770 18,900 640 17,640 560 15,880 510 14,990 400 0.3 0.6 0.4 0.04 34,000 880 30,000 720 28,000 560 25,200 500 23,800 390 20 0.004 18,360 660 16,200 540 15,120 480 13,610 440 12,850 340 0.75 0.04 34,000 880 30,000 720 28,000 560 25,200 500 23,800 390 【注意】ご使用にあたっては、21ページの表下の項目と注意を参照してください。【Note】Upon usage, please refer to comments and notes below table on page 21. 18 19

Page19

標準切削条件表 Recommended Cut t ing Condi t ions 高能率切削条件高精度切削条件高能率切削条件高精度切削条件 High efficiency cuttiing condition High accuracy cuttiing condition 高能率切削条件は14ページを参照してください。Please refer to P.14 about high efficiency cutting conditions High efficiency cuttiing condition High accuracy cuttiing condition 高能率切削条件は14ページを参照してください。Please refer to P.14 about high efficiency cutting conditions 1 2 3 4 5 1 2 3 4 5 被削材プリハードン鋼焼入れ鋼焼入れ鋼焼入れ鋼焼入れ鋼被削材プリハードン鋼焼入れ鋼焼入れ鋼焼入れ鋼焼入れ鋼 Work material Pre-hardened steels Hardened steels Hardened steels Hardened steels Hardened steels （35～45HRC）（45～55HRC）（55～65HRC）（65～68HRC）（68～72HRC） Work material Pre-hardened steels Hardened steels Hardened steels Hardened steels Hardened steels （35～45HRC）（45～55HRC）（55～65HRC）（65～68HRC）（68～72HRC）切り込み比率 Ratio to standard depth of cut 100% 85% 80% 65% 55% 切り込み比率 Ratio to standard depth of cut 100% 85% 80% 65% 55% ボール半径RE 外径DC 首下長LU 回転数送り速度回転数送り速度回転数送り速度回転数送り速度回転数送り速度ボール半径RE 外径DC 首下長LU 回転数送り速度回転数送り速度回 Ball radius Tool dia. Under neck ap Under neck ap 転数送り速度回転数送り速度回転数送り速度 length (mm) n v f n v f n v f n v f n v f Ball radius Tool dia. length (mm) n v f n v f n v f n v f n v f (mm) (mm) (mm) min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min (mm) (mm) (mm) min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min 0.08 0.003 50,000 230 50,000 200 50,000 190 45,000 170 42,500 130 1 0.04 34,000 880 30,000 720 28,000 560 25,200 500 23,800 390 0.2 0.003 50,000 230 50,000 200 50,000 190 45,000 170 42,500 130 1.5 0.038 34,000 880 30,000 720 28,000 560 25,200 500 23,800 390 0.05 0.1 0.3 0.002 50,000 230 50,000 200 50,000 190 45,000 170 42,500 130 2 0.034 34,000 880 30,000 720 28,000 560 25,200 500 23,800 390 0.5 0.002 50,000 230 50,000 200 50,000 190 45,000 170 42,500 130 2.5 0.03 34,000 880 30,000 720 28,000 560 25,200 500 23,800 390 0.12 0.007 50,000 280 46,000 230 42,000 180 37,500 160 35,500 120 3 0.027 34,000 880 30,000 720 28,000 560 25,200 500 23,800 390 0.3 0.007 50,000 280 46,000 230 42,000 180 37,500 160 35,500 120 3.5 0.023 30,600 760 27,000 620 25,200 480 22,680 430 21,420 340 0.075 0.15 0.5 0.006 50,000 280 46,000 230 42,000 180 37,500 160 35,500 120 4 0.019 30,600 760 27,000 620 25,200 480 22,680 430 21,420 340 0.75 0.005 50,000 280 46,000 230 42,000 180 37,500 160 35,500 120 4.5 0.018 30,600 720 27,000 580 25,200 450 22,680 410 21,420 320 0.3 0.6 1 0.003 46,000 230 41,400 190 37,800 150 33,750 130 31,950 100 5 0.016 30,600 720 27,000 580 25,200 450 22,680 410 21,420 320 0.15 0.012 50,000 330 45,500 270 42,000 210 37,800 190 35,700 150 5.5 0.014 30,600 720 27,000 580 25,200 450 22,680 410 21,420 320 0.3 0.012 50,000 330 45,500 270 42,000 210 37,800 190 35,700 150 6 0.012 30,600 720 27,000 580 25,200 450 22,680 410 21,420 320 0.5 0.012 50,000 330 45,500 270 42,000 210 37,800 190 35,700 150 7 0.006 27,200 600 24,000 490 22,400 380 20,160 340 19,040 270 0.75 0.01 50,000 330 45,500 270 42,000 210 37,800 190 35,700 150 8 0.006 27,200 600 24,000 490 22,400 380 20,160 340 19,040 270 1 0.009 50,000 330 45,500 270 42,000 210 37,800 190 35,700 150 9 0.005 27,200 600 24,000 490 22,400 380 20,160 340 19,040 270 0.1 0.2 1.25 0.006 45,900 270 40,500 220 37,800 170 34,020 150 32,130 120 10 0.004 23,800 530 21,000 430 19,600 330 17,640 300 16,660 230 1.5 0.006 45,900 270 40,500 220 37,800 170 34,020 150 32,130 120 12 0.003 20,400 420 18,000 350 16,800 270 15,120 240 14,280 190 2 0.005 45,900 270 40,500 220 37,800 170 34,020 150 32,130 120 0.45 0.049 34,000 980 30,000 810 28,000 660 25,200 590 23,800 460 2.5 0.004 40,800 210 36,000 170 33,600 130 30,240 120 28,560 90 2 0.049 34,000 980 30,000 810 28,000 660 25,200 590 23,800 460 3 0.002 40,800 210 36,000 170 33,600 130 30,240 120 28,560 90 0.35 0.7 4 0.027 30,600 840 27,000 690 25,200 560 22,680 510 21,420 400 0.25 0.016 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 6 0.022 30,600 790 27,000 650 25,200 540 22,680 480 21,420 370 0.5 0.016 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 8 0.008 27,200 630 24,000 520 22,400 420 20,160 380 19,040 300 0.75 0.014 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 0.5 0.08 34,000 1,090 30,000 900 28,000 780 25,200 710 23,800 550 1 0.013 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 1 0.08 34,000 1,090 30,000 900 28,000 780 25,200 710 23,800 550 1.25 0.011 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 1.5 0.08 34,000 1,090 30,000 900 28,000 780 25,200 710 23,800 550 0.15 0.3 1.5 0.01 50,000 450 45,000 380 42,000 340 37,800 300 35,700 240 2 0.064 34,000 1,090 30,000 900 28,000 780 25,200 710 23,800 550 2 0.007 45,900 370 40,500 310 37,800 270 34,020 250 32,130 190 2.5 0.06 34,000 1,090 30,000 900 28,000 780 25,200 710 23,800 550 2.5 0.006 45,900 370 40,500 310 37,800 270 34,020 250 32,130 190 0.4 0.8 3 0.055 34,000 1,090 30,000 900 28,000 780 25,200 710 23,800 550 3 0.005 45,900 370 40,500 310 37,800 270 34,020 250 32,130 190 4 0.045 34,000 1,090 30,000 900 28,000 780 25,200 710 23,800 550 3.5 0.003 36,720 260 29,400 210 26,400 180 23,760 160 22,440 130 5 0.036 30,600 880 27,000 730 25,200 640 22,680 570 21,420 450 4 0.002 36,720 260 29,400 210 26,400 180 23,760 160 22,440 130 6 0.026 30,600 880 27,000 730 25,200 640 22,680 570 21,420 450 0.3 0.034 40,800 450 36,000 360 33,600 340 30,240 300 28,560 240 8 0.016 27,200 780 24,000 650 22,400 560 20,160 510 19,040 400 0.5 0.034 40,800 450 36,000 360 33,600 340 30,240 300 28,560 240 10 0.008 27,200 740 24,000 610 22,400 530 20,160 480 19,040 370 0.75 0.034 40,800 450 36,000 360 33,600 340 30,240 300 28,560 240 12 0.006 27,200 740 24,000 610 22,400 530 20,160 480 19,040 370 1 0.032 40,800 450 36,000 360 33,600 340 30,240 300 28,560 240 0.6 0.072 32,300 1,220 28,500 1,000 26,600 890 23,940 800 22,610 620 1.5 0.027 40,800 450 36,000 360 33,600 340 30,240 300 28,560 240 2 0.072 32,300 1,220 28,500 1,000 26,600 890 23,940 800 22,610 620 0.2 0.4 2 0.022 40,800 450 36,000 360 33,600 340 30,240 300 28,560 240 0.45 0.9 4 0.046 32,300 1,220 28,500 1,000 26,600 890 23,940 800 22,610 620 2.5 0.013 36,720 360 32,400 290 30,240 270 27,220 250 25,700 190 6 0.034 29,070 980 25,650 810 23,940 720 21,550 650 20,350 510 3 0.009 36,720 360 32,400 290 30,240 270 27,220 250 25,700 190 8 0.024 25,840 880 22,800 720 21,280 640 19,150 580 18,090 450 3.5 0.006 36,720 360 32,400 290 30,240 270 27,220 250 25,700 190 0.8 0.09 30,600 1,380 27,000 1,130 25,200 1,010 22,680 910 21,420 710 4 0.004 36,720 360 32,400 290 30,240 270 27,220 250 25,700 190 1.5 0.09 30,600 1,380 27,000 1,130 25,200 1,010 22,680 910 21,420 710 4.5 0.003 32,640 310 28,800 250 26,880 230 24,190 210 22,850 160 2 0.08 30,600 1,380 27,000 1,130 25,200 1,010 22,680 910 21,420 710 5 0.002 32,640 310 28,800 250 26,880 230 24,190 210 22,850 160 2.5 0.08 30,600 1,380 27,000 1,130 25,200 1,010 22,680 910 21,420 710 0.35 0.036 34,000 610 30,000 540 28,000 480 25,200 430 23,800 330 3 0.08 30,600 1,380 27,000 1,130 25,200 1,010 22,680 910 21,420 710 0.75 0.036 34,000 610 30,000 540 28,000 480 25,200 430 23,800 330 4 0.056 30,600 1,380 27,000 1,130 25,200 1,010 22,680 910 21,420 710 1 0.036 34,000 610 30,000 540 28,000 480 25,200 430 23,800 330 5 0.048 30,600 1,380 27,000 1,130 25,200 1,010 22,680 910 21,420 710 1.5 0.032 34,000 610 30,000 540 28,000 480 25,200 430 23,800 330 6 0.032 27,540 1,120 24,300 920 22,680 820 20,410 730 19,280 570 2 0.028 34,000 610 30,000 540 28,000 480 25,200 430 23,800 330 0.5 1 7 0.032 27,540 1,120 24,300 920 22,680 820 20,410 730 19,280 570 2.5 0.026 30,600 500 27,000 440 25,200 390 22,680 350 21,420 270 8 0.032 27,540 1,120 24,300 920 22,680 820 20,410 730 19,280 570 0.25 0.5 3 0.024 30,600 500 27,000 440 25,200 390 22,680 350 21,420 270 9 0.024 27,540 1,120 24,300 920 22,680 820 20,410 730 19,280 570 4 0.016 30,600 500 27,000 440 25,200 390 22,680 350 21,420 270 10 0.02 27,540 1,120 24,300 920 22,680 820 20,410 730 19,280 570 5 0.014 30,600 500 27,000 440 25,200 390 22,680 350 21,420 270 12 0.01 24,480 940 21,600 770 20,160 690 18,140 620 17,140 480 5.5 0.006 27,200 420 24,000 370 22,400 320 20,160 290 19,040 230 13 0.009 24,480 940 21,600 770 20,160 690 18,140 620 17,140 480 6 0.005 27,200 420 24,000 370 22,400 320 20,160 290 19,040 230 14 0.008 24,480 940 21,600 770 20,160 690 18,140 620 17,140 480 7 0.004 27,200 420 24,000 370 22,400 320 20,160 290 19,040 230 16 0.006 24,480 940 21,600 770 20,160 690 18,140 620 17,140 480 8 0.003 27,200 420 24,000 370 22,400 320 20,160 290 19,040 230 18 0.005 21,420 770 18,900 640 17,640 560 15,880 510 14,990 400 0.3 0.6 0.4 0.04 34,000 880 30,000 720 28,000 560 25,200 500 23,800 390 20 0.004 18,360 660 16,200 540 15,120 480 13,610 440 12,850 340 0.75 0.04 34,000 880 30,000 720 28,000 560 25,200 500 23,800 390 【注意】ご使用にあたっては、21ページの表下の項目と注意を参照してください。【Note】Upon usage, please refer to comments and notes below table on page 21. 18 19

Page20

標準切削条件表 Recommended Cut t ing Condi t ions 高能率切削条件高精度切削条件高能率切削条件高精度切削条件 High efficiency cuttiing condition High accuracy cuttiing condition 高能率切削条件は14ページを参照してください。Please refer to P.14 about high efficiency cutting conditions High efficiency cuttiing condition High accuracy cuttiing condition 高能率切削条件は14ページを参照してください。Please refer to P.14 about high efficiency cutting conditions 1 2 3 4 5 1 2 3 4 5 被削材プリハードン鋼焼入れ鋼焼入れ鋼焼入れ鋼焼入れ鋼被削材プリハードン鋼焼入れ鋼焼入れ鋼焼入れ鋼焼入れ鋼 Work material Pre-hardened steels Hardened steels Hardened steels Hardened steels Hardened steels （35～45HRC）（45～55HRC）（55～65HRC）（65～68HRC）（68～72HRC） Work material Pre-hardened steels Hardened steels Hardened steels Hardened steels Hardened steels （35～45HRC）（45～55HRC）（55～65HRC）（65～68HRC）（68～72HRC）切り込み比率 Ratio to standard depth of cut 100% 85% 80% 65% 55% 切り込み比率 Ratio to standard depth of cut 100% 85% 80% 65% 55% ボール半径RE 外径DC 首下長LU 回転数送り速度回転数送り速度回転数送り速度回転数送り速度回転数送り速度ボール半径RE 外径DC 首下長LU ap 回転数送り速度回転数送り速度回転数送り速度回転数送り速度回転数送り速度 Ball radius Tool dia. Under neck ap length (mm) n v f n v f n v f n v f n v f Ball radius Tool dia. Under neck (mm) (mm) length (mm) n v f n v f n v f n v f n v f (mm) min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min (mm) (mm) (mm) min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min min-1 mm/min 2 0.08 28,560 1,300 25,200 1,090 23,520 970 21,170 870 19,990 680 6 0.2 15,730 1,690 13,880 1,370 12,950 1,130 11,660 1,010 11,070 810 4 0.056 28,560 1,300 25,200 1,090 23,520 970 21,170 870 19,990 680 10 0.136 15,730 1,690 13,880 1,370 12,950 1,130 11,660 1,010 11,070 810 0.55 1.1 6 0.032 26,010 1,090 22,950 920 21,420 810 19,280 730 18,210 570 15 0.08 14,150 1,370 12,490 1,110 11,660 910 10,490 820 9,970 660 1.25 2.5 8 0.032 26,010 1,090 22,950 920 21,420 810 19,280 730 18,210 570 20 0.064 14,150 1,370 12,490 1,110 11,660 910 10,490 820 9,970 660 10 0.02 26,010 1,090 22,950 920 21,420 810 19,280 730 18,210 570 25 0.052 14,150 1,230 12,490 1,000 11,660 820 10,490 740 9,970 590 2 0.077 26,150 1,210 23,080 1,000 21,540 890 19,380 800 18,310 620 30 0.035 12,580 1,150 11,100 930 10,360 770 9,320 690 8,860 550 3 0.077 26,150 1,210 23,080 1,000 21,540 890 19,380 800 18,310 620 6 0.24 13,600 1,820 12,000 1,510 11,200 1,340 10,080 1,210 9,580 970 4 0.064 26,150 1,210 23,080 1,000 21,540 890 19,380 800 18,310 620 8 0.24 13,600 1,820 12,000 1,510 11,200 1,340 10,080 1,210 9,580 970 0.6 1.2 6 0.048 26,150 1,210 23,080 1,000 21,540 890 19,380 800 18,310 620 10 0.168 13,600 1,820 12,000 1,510 11,200 1,340 10,080 1,210 9,580 970 8 0.032 24,480 1,130 21,600 950 20,160 810 18,140 730 17,140 560 13 0.168 13,600 1,820 12,000 1,510 11,200 1,340 10,080 1,210 9,580 970 10 0.028 24,480 1,100 21,600 860 20,160 730 18,140 650 17,140 510 1.5 3 16 0.168 13,600 1,640 12,000 1,360 11,200 1,210 10,080 1,090 9,580 870 12 0.024 24,480 1,100 21,600 860 20,160 730 18,140 650 17,140 510 20 0.096 12,240 1,480 10,800 1,230 10,080 1,090 9,070 980 8,620 780 3 0.088 21,420 1,160 18,900 980 17,640 880 15,880 790 14,990 620 25 0.064 12,240 1,480 10,800 1,230 10,080 1,090 9,070 980 8,620 780 8 0.044 21,420 1,160 18,900 980 17,640 880 15,880 790 14,990 620 30 0.064 12,240 1,480 10,800 1,230 10,080 1,090 9,070 980 8,620 780 0.7 1.4 12 0.028 21,420 1,040 18,900 890 17,640 790 15,880 720 14,990 560 35 0.051 10,880 1,240 9,600 1,030 8,960 910 8,060 820 7,660 660 16 0.014 19,040 870 16,800 740 15,680 670 14,110 600 13,330 470 10 0.216 11,690 1,760 10,310 1,430 9,630 1,180 8,660 1,060 8,230 850 2 0.096 23,800 1,430 21,000 1,130 19,600 980 17,640 880 16,660 690 15 0.192 11,690 1,760 10,310 1,430 9,630 1,180 8,660 1,060 8,230 850 2.5 0.096 23,800 1,430 21,000 1,130 19,600 980 17,640 880 16,660 690 1.75 3.5 25 0.112 10,520 1,430 9,280 1,160 8,660 950 7,800 860 7,410 680 3 0.096 23,800 1,430 21,000 1,130 19,600 980 17,640 880 16,660 690 35 0.072 10,520 1,430 9,280 1,160 8,660 950 7,800 860 7,410 680 4 0.08 23,800 1,430 21,000 1,130 19,600 980 17,640 880 16,660 690 45 0.058 9,350 1,200 8,250 980 7,700 800 6,930 720 6,580 580 5 0.08 23,800 1,430 21,000 1,130 19,600 980 17,640 880 16,660 690 8 0.32 9,780 1,760 8,630 1,470 8,050 1,290 7,250 1,160 6,880 930 6 0.08 23,800 1,430 21,000 1,130 19,600 980 17,640 880 16,660 690 10 0.32 9,780 1,760 8,630 1,470 8,050 1,290 7,250 1,160 6,880 930 0.75 1.5 8 0.048 21,420 1,160 18,900 920 17,640 790 15,880 720 14,990 560 12 0.256 9,780 1,760 8,630 1,470 8,050 1,290 7,250 1,160 6,880 930 10 0.048 21,420 1,160 18,900 920 17,640 790 15,880 720 14,990 560 13 0.256 9,780 1,760 8,630 1,470 8,050 1,290 7,250 1,160 6,880 930 12 0.048 21,420 1,160 18,900 920 17,640 790 15,880 720 14,990 560 16 0.224 9,780 1,760 8,630 1,470 8,050 1,290 7,250 1,160 6,880 930 14 0.04 19,040 970 16,800 770 15,680 670 14,110 600 13,330 470 20 0.224 9,780 1,760 8,630 1,470 8,050 1,290 7,250 1,160 6,880 930 2 4 16 0.015 19,040 970 16,800 770 15,680 670 14,110 600 13,330 470 25 0.128 8,800 1,430 7,760 1,190 7,250 1,040 6,520 940 6,190 750 18 0.015 19,040 970 16,800 770 15,680 670 14,110 600 13,330 470 30 0.128 8,800 1,430 7,760 1,190 7,250 1,040 6,520 940 6,190 750 20 0.015 19,040 970 16,800 770 15,680 670 14,110 600 13,330 470 35 0.08 8,800 1,430 7,760 1,190 7,250 1,040 6,520 940 6,190 750 4 0.11 22,100 1,370 19,500 1,170 18,200 1,020 16,380 920 15,470 710 40 0.08 8,800 1,430 7,760 1,190 7,250 1,040 6,520 940 6,190 750 8 0.088 22,100 1,370 19,500 1,170 18,200 1,020 16,380 920 15,470 710 45 0.064 7,820 1,200 6,900 1,000 6,440 880 5,800 790 5,510 630 0.8 1.6 12 0.052 19,890 1,110 17,550 950 16,380 830 14,740 740 13,920 580 50 0.056 7,820 1,200 6,900 1,000 6,440 880 5,800 790 5,510 630 16 0.032 19,890 1,110 17,550 950 16,380 830 14,740 740 13,920 580 10 0.392 7,650 1,530 6,750 1,350 6,300 1,130 5,670 1,020 5,390 820 20 0.016 17,680 930 15,600 800 14,560 690 13,100 620 12,380 490 20 0.28 7,650 1,530 6,750 1,350 6,300 1,130 5,670 1,020 5,390 820 4 0.147 22,100 1,550 19,500 1,290 18,200 1,090 16,380 980 15,470 760 2.5 5 25 0.28 7,650 1,530 6,750 1,350 6,300 1,130 5,670 1,020 5,390 820 8 0.104 22,100 1,550 19,500 1,290 18,200 1,090 16,380 980 15,470 760 30 0.16 6,890 1,380 6,080 1,220 5,670 1,020 5,100 920 4,850 740 0.9 1.8 12 0.056 19,890 1,250 17,550 1,040 16,380 890 14,740 800 13,920 620 40 0.16 6,890 1,240 6,080 1,090 5,670 920 5,100 830 4,850 660 16 0.036 19,890 1,250 17,550 1,040 16,380 890 14,740 800 13,920 620 12 0.48 7,650 1,890 6,750 1,540 6,300 1,260 5,670 1,130 5,390 910 20 0.018 17,680 1,050 15,600 880 14,560 740 13,100 670 12,380 520 3 20 0.4 7,230 1,660 6,380 1,350 5,950 1,110 5,360 990 5,090 800 6 2.5 0.16 17,850 1,610 15,750 1,360 14,700 1,180 13,230 1,060 12,500 820 30 0.336 6,800 1,360 6,000 1,200 5,600 1,010 5,040 910 4,790 730 3 0.16 17,850 1,610 15,750 1,360 14,700 1,180 13,230 1,060 12,500 820 50 0.12 6,120 1,100 5,400 970 5,040 820 4,540 730 4,310 590 4 0.16 17,850 1,610 15,750 1,360 14,700 1,180 13,230 1,060 12,500 820 4 8 24 0.5 6,400 1,690 5,720 1,320 4,180 1,170 3,960 870 3,760 700 5 0.16 17,850 1,610 15,750 1,360 14,700 1,180 13,230 1,060 12,500 820 5 10 30 0.6 5,100 1,460 4,510 1,130 3,520 1,000 3,190 770 3,030 620 6 0.16 17,850 1,430 15,750 1,200 14,700 1,060 13,230 950 12,500 740 6 12 36 0.8 4,200 1,240 3,850 1,000 2,640 880 2,640 660 2,510 530 8 0.112 17,850 1,430 15,750 1,200 14,700 1,060 13,230 950 12,500 740 10 0.112 17,850 1,290 15,750 1,070 14,700 940 13,230 850 12,500 660 ※（１）apは被削材グル－プ1での目安を示しています。その他のグループの場合は、上表の切込み比率を目安に調整してください。 12 0.064 16,070 1,160 14,180 960 13,230 850 11,910 760 11,250 590 ※（２）リブ加工や止まり溝など、切りくずがつまりやすい切削の場合、切込み設定は基本切込みに切込み比率をかけて算出した切込み量を、　　　さらにその80％まで小さくして使用してください。 1 2 13 0.064 16,070 1,160 14,180 960 13,230 850 11,910 760 11,250 590 ※（３）aeの設定はap×切込み比率×3～5倍を目安に調整してください。仕上げ加工を行う場合、理論カスプハイトを計算し設定してください。 14 0.064 16,070 1,160 14,180 960 13,230 850 11,910 760 11,250 590 ※(1) ap is shown as the criteria for Group 1 workpieces. For other groups, adjust the cutting depth according to the cutting depth factors in the above table. 16 0.064 16,070 1,040 14,180 870 13,230 760 11,910 690 11,250 530 ※(2) When performing cutting where cutting chips may cause clogging, such as for rib cutting, blind grooves, etc., cutting depth setting should be set by multiplying a cutting 　depth factor to calculate the cutting depth amount, and this amount should then be reduced to 80% of the calculated value. 18 0.048 16,070 1,040 14,180 870 13,230 760 11,910 690 11,250 530 ※(3) Adjust by setting ae to (3 to 5)×(ap)×(cutting depth ratio). When performing finishing processing, calculate the theoretical cusp height and set accordingly. 20 0.04 16,070 1,040 14,180 870 13,230 760 11,910 690 11,250 530 【切込み設定例】EPDBEH2020-10-TH3の工具で焼入れ鋼（50HRC）をリブ溝等高線切削する場合、 22 0.034 15,170 930 13,390 770 12,500 680 11,250 610 10,620 480 切込み=0.112（ap）×0.85（焼入れ鋼グループ2の切込み比率）×0.8（閉鎖域の切削）=0.076mm 25 0.028 14,280 870 12,600 730 11,760 640 10,580 580 10,000 450 Cutting depth setting example: When cutting rib groove contours in hardened steel (50HRC) using an EPDBEH2020-10-TH3 tool: Cutting depth = 0.112 (ap) × 0.85 (cutting depth factor for Group 2 hardened steel) × 0.8 (for closed-area cutting) = 0.076mm 30 0.012 14,280 870 12,600 730 11,760 640 10,580 580 10,000 450 35 0.01 12,500 720 11,030 600 10,290 530 9,260 470 8,750 370 【注意】①基本的にはDry（エアーブロー）切削を推奨しますが、被削材、加工形状に合わせて、適切なクーラントを使用してください。 40 ②この標準切削条件表は切削条件の目安を示すものです。実際の加工では加工形状、目的、使用機械等により条件を調整してください。 0.008 10,710 620 9,450 510 8,820 450 7,940 410 7,500 320 ③機械の回転数が足りない場合は、回転数と送り速度を同じ比率で下げてください。【Note】 ① Although basically dry (air blow) cutting is recommended, please use appropriate coolant according to the work material and machining shape. ② These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type. ③ If the rpm of the machine is low, lower the feed rate also to put the rpm and feed rate in the same ratio. 20 21

動機*	具体的な検討のため情報収集のため
この内容をご存知でしたか？	詳しく知っていた名前だけは知っていた知らなかった
導入予定時期を教えて下さい	1ヵ月以内3ヵ月以内6ヵ月以内1年以内未定
あなたの立場を教えて下さい*	自社での導入を検討する立場顧客に提案・販売する立場
お問い合わせ・ご質問

動機
この内容をご存知でしたか？
導入予定時期を教えて下さい
あなたの立場を教えて下さい
お問い合わせ・ご質問

お名前
電話番号
会社名
事業所名
部署名
業態
職務区分
所在地

高硬度鋼加工用ボールエンドミル　エポックディープボールエボリューションハード-TH3　EPDBEH-TH3

焼きばめホルダに適したショートシャンクタイプを新発売

このカタログについて

この企業の関連カタログ

このカタログの内容

高硬度鋼加工用ボールエンドミル エポックディープボールエボリューションハード-TH3 EPDBEH-TH3

焼きばめホルダに適した ショートシャンクタイプを新発売

このカタログについて

この企業の関連カタログ

このカタログの内容

高硬度鋼加工用ボールエンドミル　エポックディープボールエボリューションハード-TH3　EPDBEH-TH3

焼きばめホルダに適したショートシャンクタイプを新発売