1/30ページ
ダウンロード(653.1Kb)
ADG5436F Fault Protection and Detection, 10 Ω RON, Dual SPDT Switch
製品カタログ
このカタログについて
ドキュメント名 | ADG5436F Fault Protection and Detection, 10 Ω RON, Dual SPDT Switch |
---|---|
ドキュメント種別 | 製品カタログ |
ファイルサイズ | 653.1Kb |
取り扱い企業 | マウザー・エレクトロニクス (この企業の取り扱いカタログ一覧) |
この企業の関連カタログ
このカタログの内容
Page1
FEATURES、APPLICATIONS、FUNCTIONAL BLOCK DIAGRAM、GENERAL DESCRIPTION、PRODUCT HIGHLIGHTS
Fault Protection and Detection,
10 Ω RON, Dual SPDT Switch
Data Sheet ADG5436F
FEATURES FUNCTIONAL BLOCK DIAGRAM
Overvoltage protection up to −55 V and +55 V ADG5436F
Power-off protection up to −55 V and +55 V
Overvoltage detection on source pins S1A S2A
Interrupt flags indicate fault status D1 D2
S1B S2B
Low on resistance: 10 Ω (typical)
On-resistance flatness of 0.5 Ω (maximum)
6 kV human body model (HBM) ESD rating FAULT
DETECTION SF
Latch-up immune under any circumstance +
SWITCH DRIVER FF
Known state without digital inputs present
VSS to VDD analog signal range IN1 IN2 EN DR
±5 V to ±22 V dual supply operation
NOTES
8 V to 44 V single-supply operation 1. SWITCHES SHOWN FOR A LOGIC 1 INPUT.
Fully specified at ±15 V, ±20 V, +12 V, and +36 V Figure 1.
APPLICATIONS
Analog input/output modules
Process control/distributed control systems
Data acquisition
Instrumentation
Avionics
Automatic test equipment
Communication systems
Relay replacement
GENERAL DESCRIPTION
The ADG5436F is an analog multiplexer, containing two resistance of the ADG5436F, combined with the on-resistance
independently selectable single-pole, double-throw (SPDT) flatness over a significant portion of the signal range, makes it
switches. An EN input is used to disable all the switches. For use an ideal solution for data acquisition and gain switching
in multiplexer applications, both switches exhibit break-before- applications where excellent linearity and low distortion are
make switching action. critical.
Each channel conducts equally well in both directions when on, Note that, throughout this data sheet, the dual function pin names
and each switch has an input signal range that extends to the are referenced only by the relevant function where applicable. See
supplies. The digital inputs are compatible with 3 V logic inputs the Pin Configurations and Function Descriptions section for
over the full operating supply range. full pin names and function descriptions.
When no power supplies are present, the switch remains in the off PRODUCT HIGHLIGHTS
condition, and the channel inputs are high impedance. Under 1. Source pins are protected against voltages greater than the
normal operating conditions, if the analog input signal level on supply rails, up to −55 V and +55 V.
any Sxx pin exceeds VDD or VSS by a threshold voltage, VT, the 2. Source pins are protected against voltages between −55 V
channel turns off and that Sxx pin becomes high impedance. If and +55 V in an unpowered state.
the channel is on, the drain pin reacts according to the drain 3. Overvoltage detection with digital output indicates the
response (DR) input pin. If the DR pin is left floating or pulled operating state of the switches.
high, the drain remains high impedance and floats. If the DR pin 4. Trench isolation guards against latch-up.
is pulled low, the drain pulls to the exceeded rail. Input signal 5. Optimized for low on resistance and on-resistance flatness.
levels of up to +55 V or −55 V relative to ground are blocked, in 6. The ADG5436F operates from a dual supply of ±5 V up to
both the powered and unpowered conditions. The low on ±22 V, or a single power supply of 8 V up to 44 V.
Rev. C Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Tel: 781.329.4700 ©2015–2017 Analog Devices, Inc. All rights reserved.
Trademarks and registered trademarks are the property of their respective owners. Technical Support www.analog.com
12882-001
Page2
TABLE OF CONTENTS、REVISION HISTORY
ADG5436F Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1 Test Circuits ..................................................................................... 20
Applications ....................................................................................... 1 Terminology .................................................................................... 24
Functional Block Diagram .............................................................. 1 Theory of Operation ...................................................................... 26
General Description ......................................................................... 1 Switch Architecture .................................................................... 26
Product Highlights ........................................................................... 1 Fault Protection .......................................................................... 27
Revision History ............................................................................... 2 Applications Information .............................................................. 28
Specifications ..................................................................................... 3 Power Supply Rails ..................................................................... 28
±15 V Dual Supply ....................................................................... 3 Power Supply Sequencing Protection ...................................... 28
±20 V Dual Supply ....................................................................... 5 Signal Range ................................................................................ 28
12 V Single Supply ........................................................................ 7 Low Impedance Channel Protection ....................................... 28
36 V Single Supply ........................................................................ 9 Power Supply Recommendations ............................................. 28
Continuous Current per Channel, Sxx or Dx ......................... 11 High Voltage Surge Suppression .............................................. 28
Absolute Maximum Ratings .......................................................... 12 Intelligent Fault Detection ........................................................ 29
ESD Caution ................................................................................ 12 Large Voltage, High Frequency Signals ................................... 29
Pin Configurations and Function Descriptions ......................... 13 Outline Dimensions ....................................................................... 30
Truth Tables for Switches .......................................................... 14 Ordering Guide .......................................................................... 30
Typical Performance Characteristics ........................................... 15
REVISION HISTORY
10/2017—Rev. B to Rev. C 5/2015—Rev. 0 to Rev. A
Changes to Fault Drain Leakage Current With Overvoltage Added 16-Lead LFCSP Package ....................................... Universal
Parameter, Table 1 ............................................................................. 3 Changes to Table 1 ............................................................................. 3
Changes to Fault Drain Leakage Current With Overvoltage Changes to Table 2 ............................................................................. 5
Parameter, Table 2 ............................................................................. 7 Changes to Table 3 ............................................................................. 7
Changes to Fault Drain Leakage Current With Overvoltage Changes to Table 4 ............................................................................. 9
Parameter, Table 4 ............................................................................ 9 Changes to Table 5 .......................................................................... 11
Updated Outline Dimensions ....................................................... 30 Changes to Table 6 .......................................................................... 12
Changes to Ordering Guide .......................................................... 30 Added Figure 3; Renumbered Sequentially ................................ 13
Changes to Table 7 .......................................................................... 13
1/2016—Rev. A to Rev. B Added Figure 53 ............................................................................. 30
Changes to Table 1 ............................................................................ 3 Updated Outline Dimensions ....................................................... 30
Changes to Table 2 ............................................................................ 5 Changes to Ordering Guide .......................................................... 30
Changes to Table 3 ............................................................................ 7
Changes to Table 4 ............................................................................ 9 1/2015—Revision 0: Initial Version
Changes to ESD Performance Section ......................................... 26
Rev. C | Page 2 of 30
Page3
SPECIFICATIONS、±15 V DUAL SUPPLY
Data Sheet ADG5436F
SPECIFICATIONS
±15 V DUAL SUPPLY
VDD = 15 V ± 10%, VSS = −15 V ± 10%, GND = 0 V, CDECOUPLING = 0.1 µF, unless otherwise noted.
Table 1.
−40°C to −40°C to
Parameter +25°C +85°C +125°C Unit Test Conditions/Comments
ANALOG SWITCH VDD = 13.5 V, VSS = −13.5 V, see Figure 30
Analog Signal Range VDD to VSS V
On Resistance, RON 10 Ω typ Voltage on the Sxx pins (VS) = ±10 V, IS = −10 mA
11.2 14 16.5 Ω max
9.5 Ω typ VS = ±9 V, IS = −10 mA
10.7 13.5 16 Ω max
On-Resistance Match 0.15 Ω typ VS = ±10 V, IS = −10 mA
Between Channels, ∆RON
0.65 0.8 0.95 Ω max
0.15 Ω typ VS = ±9 V, IS = −10 mA
0.6 0.7 0.8 Ω max
On-Resistance Flatness, 0.6 Ω typ VS = ±10 V, IS = −10 mA
RFLAT(ON)
0.9 1.1 1.1 Ω max
0.1 Ω typ VS = ±9 V, IS = −10 mA
0.4 0.5 0.5 Ω max
Threshold Voltage, VT 0.7 V typ See Figure 26
LEAKAGE CURRENTS VDD = 16.5 V, VSS = −16.5 V
Source Off Leakage, IS (Off ) ±0.1 nA typ VS = ±10 V, voltage on the Dx pin (VD) = ∓10 V, see Figure 31
±1.5 ±5.0 ±21 nA max
Drain Off Leakage, ID (Off ) ±0.1 nA typ VS = ±10 V, VD = ∓10 V, see Figure 31
±1.5 ±7.0 ±25 nA max
Channel On Leakage, ID (On), ±0.5 nA typ VS = VD = ±10 V, see Figure 32
IS (On)
±1.5 ±5.0 ±21 nA max
FAULT
Source Leakage Current, IS
With Overvoltage ±72 µA typ VDD = 16.5 V, VSS = −16.5 V, GND = 0 V, VS = ±55 V,
see Figure 35
Power Supplies ±49 µA typ VDD = 0 V or floating, VSS = 0 V or floating, GND = 0 V, EN = 0 V
Grounded or Floating or floating, INx = 0 V or floating, VS = ±55 V, see Figure 36
Drain Leakage Current, ID DR = floating or >2 V
With Overvoltage ±2.0 nA typ VDD = 16.5 V, VSS = −16.5 V, GND = 0 V, VS = ±55 V, see
Figure 35
±20 ±30 ±65 nA max
Power Supplies ±10 nA typ VDD = 0 V, VSS = 0 V, GND = 0 V, INx = 0 V or floating,
Grounded VS = ±55 V, EN = 0 V, see Figure 36
±30 ±50 ±100 nA max
Power Supplies Floating ±10 ±10 ±10 µA typ VDD = floating, VSS = floating, GND = 0 V, VS = ±55 V,
EN = 0 V, see Figure 36
DIGITAL INPUTS/OUTPUTS
Input Voltage High, VINH 2.0 V min
Input Voltage Low, VINL 0.8 V max
Input Current, IINL or IINH ±0.7 µA typ VIN = VGND or VDD
±1.2 µA max
Digital Input Capacitance, CIN 6.0 pF typ
Output Voltage High, VOH 2.0 V min
Output Voltage Low, VOL 0.8 V max
Rev. C | Page 3 of 30
Page4
ADG5436F Data Sheet
−40°C to −40°C to
Parameter +25°C +85°C +125°C Unit Test Conditions/Comments
DYNAMIC CHARACTERISTICS1
Transition Time, tTRANSITION 400 ns typ RL = 300 Ω, CL = 35 pF
540 555 570 ns max VS = 10 V, see Figure 46
tON (EN) 435 ns typ RL = 300 Ω, CL = 35 pF
515 530 550 ns max VS = 10 V, see Figure 45
tOFF (EN) 165 ns typ RL = 300 Ω, CL = 35 pF
210 215 220 ns max VS = 10 V, see Figure 45
Break-Before-Make Time 320 ns typ RL = 300 Ω, CL = 35 pF
Delay, tD
190 ns min VS = 10 V, see Figure 44
Overvoltage Response 510 ns typ RL = 1 kΩ, CL = 2 pF, see Figure 39
Time, tRESPONSE
680 725 750 ns max
Overvoltage Recovery Time, 820 ns typ RL = 1 kΩ, CL = 2 pF, see Figure 40
tRECOVERY
1100 1150 1200 ns max
Interrupt Flag Response 85 115 ns typ CL = 12 pF, see Figure 41
Time, tDIGRESP
Interrupt Flag Recovery 60 85 µs typ CL = 12 pF, see Figure 42
Time, tDIGREC
600 ns typ CL = 12 pF, RPULLUP = 1 kΩ, see Figure 43
Charge Injection, QINJ −724 pC typ VS = 0 V, RS = 0 Ω, CL = 1 nF, see Figure 47
Off Isolation −71 dB typ RL = 50 Ω, CL = 5 pF, f = 1 MHz, see Figure 33
Channel-to-Channel Crosstalk −73 dB typ RL = 50 Ω, CL = 5 pF, f = 1 MHz, see Figure 34
Total Harmonic Distortion 0.001 % typ RL = 10 kΩ, VS = 15 V p-p, f = 20 Hz to 20 kHz, see Figure 38
Plus Noise, THD + N
−3 dB Bandwidth 169 MHz typ RL = 50 Ω, CL = 5 pF, see Figure 37
Insertion Loss −0.8 dB typ RL = 50 Ω, CL = 5 pF, f = 1 MHz, see Figure 37
Source Capacitance (CS), Off 12 pF typ VS = 0 V, f = 1 MHz
Drain Capacitance (CD), Off 24 pF typ VS = 0 V, f = 1 MHz
CD (On), CS (On) 37 pF typ VS = 0 V, f = 1 MHz
POWER REQUIREMENTS VDD = 16.5 V, VSS = −16.5 V, GND = 0 V, digital inputs = 0 V,
5 V, or VDD
Normal Mode
IDD 0.9 mA typ
1.2 1.3 mA max
IGND 0.4 mA typ
0.55 0.6 mA max
ISS 0.5 mA typ
0.65 0.7 mA max
Fault Mode VS = ±55 V
IDD 1.2 mA typ
1.6 1.8 mA max
IGND 0.8 mA typ
1.0 1.1 mA max
ISS 0.5 mA typ Digital inputs = 5 V
1.0 1.8 mA max VS = ±55 V, VD = 0 V
VDD/VSS ±5 V min GND = 0 V
±22 V max GND = 0 V
1 Guaranteed by design. Not subject to production test.
Rev. C | Page 4 of 30
Page5
±20 V DUAL SUPPLY
Data Sheet ADG5436F
±20 V DUAL SUPPLY
VDD = 20 V ± 10%, VSS = −20 V ± 10%, GND = 0 V, CDECOUPLING = 0.1 µF, unless otherwise noted.
Table 2.
−40°C to −40°C to
Parameter +25°C +85°C +125°C Unit Test Conditions/Comments
ANALOG SWITCH VDD = 18 V, VSS = −18 V, see Figure 30
Analog Signal Range VDD to VSS V
On Resistance, RON 10 Ω typ VS = ±15 V, IS = −10 mA
11.5 14.5 16.5 Ω max
9.5 Ω typ VS = ±13.5 V, IS = −10 mA
11 14 16.5 Ω max
On-Resistance Match Between Channels, ∆RON 0.15 Ω typ VS = ±15 V, IS = −10 mA
0.65 0.8 0.95 Ω max
0.15 Ω typ VS = ±13.5 V, IS = −10 mA
0.6 0.7 0.8 Ω max
On-Resistance Flatness, RFLAT(ON) 1.0 Ω typ VS = ±15 V, IS = −10 mA
1.4 1.5 1.5 Ω max
0.1 Ω typ VS = ±13.5 V, IS = −10 mA
0.4 0.5 0.5 Ω max
Threshold Voltage, VT 0.7 V typ See Figure 26
LEAKAGE CURRENTS VDD = 22 V, VSS = −22 V
Source Off Leakage, IS (Off ) ±0.1 nA typ VS = ±15 V, VD = ±15 V, see Figure 31
±1.5 ±5.0 ±21 nA max
Drain Off Leakage, ID (Off ) ±0.1 nA typ VS = ±15 V, VD = ±15 V, see Figure 31
±1.5 ±7.0 ±25 nA max
Channel On Leakage, ID (On), IS (On) ±0.5 nA typ VS = VD = ±15 V, see Figure 32
±1.5 ±5.0 ±21 nA max
FAULT
Source Leakage Current, IS
With Overvoltage ±84 µA typ VDD = +22 V, VSS = −22 V, GND = 0 V,
VS = ±55 V, see Figure 35
Power Supplies Grounded or Floating ±49 µA typ VDD = 0 V or floating, VSS = 0 V or floating,
GND = 0 V, EN = 0 V or floating, INx = 0 V
or floating, VS = ±55 V, see Figure 36
Drain Leakage Current, ID DR = floating or >2 V
With Overvoltage ±5.0 nA typ VDD = +22 V, VSS = −22 V, GND = 0 V,
INx = 0 V or floating, VS = ±55 V, see
Figure 35
±1.0 ±1.0 ±1.0 µA max
Power Supplies Grounded ±10 nA typ VDD = 0 V, VSS = 0 V, GND = 0 V, VS =
±55 V, EN = 0 V, see Figure 36
±30 ±50 ±100 nA max
Power Supplies Floating ±10 ±10 ±10 µA typ VDD = floating, VSS = floating, GND =
0 V, VS = ±55 V, EN = 0 V, see Figure 36
DIGITAL INPUTS
Input Voltage High, VINH 2.0 V min
Input Voltage Low, VINL 0.8 V max
Input Current, IINL or IINH 0.7 µA typ VIN = VGND or VDD
1.2 µA max
Digital Input Capacitance, CIN 6.0 pF typ
Output Voltage High, VOH 2.0 V min
Output Voltage Low, VOL 0.8 V max
Rev. C | Page 5 of 30
Page6
ADG5436F Data Sheet
−40°C to −40°C to
Parameter +25°C +85°C +125°C Unit Test Conditions/Comments
DYNAMIC CHARACTERISTICS1
Transition Time, tTRANSITION 405 ns typ RL = 300 Ω, CL = 35 pF
540 555 570 ns max VS = 10 V, see Figure 46
tON (EN) 430 ns typ RL = 300 Ω, CL = 35 pF
535 560 585 ns max VS = 10 V, see Figure 45
tOFF (EN) 170 ns typ RL = 300 Ω, CL = 35 pF
205 210 215 ns max VS = 10 V, see Figure 45
Break-Before-Make Time Delay, tD 330 ns typ RL = 300 Ω, CL = 35 pF
205 ns min VS = 10 V, see Figure 44
Overvoltage Response Time, tRESPONSE 430 ns typ RL = 1 kΩ, CL = 2 pF, see Figure 39
560 605 630 ns max
Overvoltage Recovery Time, tRECOVERY 930 ns typ RL = 1 kΩ, CL = 2 pF, see Figure 40
1300 1500 1700 ns max
Interrupt Flag Response Time, tDIGRESP 85 115 ns typ CL = 12 pF, see Figure 41
Interrupt Flag Recovery Time, tDIGREC 60 85 µs typ CL = 12 pF, see Figure 42
600 ns typ CL = 12 pF, RPULLUP = 1 kΩ, see Figure 43
Charge Injection, QINJ −737 pC typ VS = 0 V, RS = 0 Ω, CL = 1 nF, see
Figure 47
Off Isolation −72 dB typ RL = 50 Ω, CL = 5 pF, f = 1 MHz, see
Figure 33
Channel-to-Channel Crosstalk −73 dB typ RL = 50 Ω, CL = 5 pF, f = 1 MHz, see
Figure 34
Total Harmonic Distortion Plus Noise, THD + N 0.001 % typ RL = 10 kΩ, VS = 20 V p-p, f = 20 Hz to
20 kHz, see Figure 38
−3 dB Bandwidth 171 MHz typ RL = 50 Ω, CL = 5 pF, see Figure 37
Insertion Loss −0.8 dB typ RL = 50 Ω, CL = 5 pF, f = 1 MHz, see
Figure 37
CS (Off ) 11 pF typ VS = 0 V, f = 1 MHz
CD (Off ) 23 pF typ VS = 0 V, f = 1 MHz
CD (On), CS (On) 36 pF typ VS = 0 V, f = 1 MHz
POWER REQUIREMENTS VDD = 22 V, VSS = −22 V, digital inputs =
0 V, 5 V, or VDD
Normal Mode
IDD 0.9 mA typ
1.2 1.3 mA max
IGND 0.4 mA typ
0.55 0.6 mA max
ISS 0.5 mA typ
0.65 0.7 mA max
Fault Mode VS = ±55 V
IDD 1.2 mA typ
1.6 1.8 mA max
IGND 0.8 mA typ
1.0 1.1 mA max
ISS 0.5 mA typ Digital inputs = 5 V
1.0 1.8 mA max VS = ±55 V, VD = 0 V
VDD/VSS ±5 V min GND = 0 V
±22 V max GND = 0 V
1 Guaranteed by design. Not subject to production test.
Rev. C | Page 6 of 30
Page7
12 V SINGLE SUPPLY
Data Sheet ADG5436F
12 V SINGLE SUPPLY
VDD = 12 V ± 10%, VSS = 0 V, GND = 0 V, CDECOUPLING = 0.1 µF, unless otherwise noted.
Table 3.
−40°C to −40°C to
Parameter +25°C +85°C +125°C Unit Test Conditions/Comments
ANALOG SWITCH VDD = 10.8 V, VSS = 0 V, see Figure 30
Analog Signal Range 0 V to VDD V
On Resistance, RON 22 Ω typ VS = 0 V to 10 V, IS = −10 mA
24.5 31 37 Ω max
10 Ω typ VS = 3.5 V to 8.5 V, IS = −10 mA
11.2 14 16.5 Ω max
On-Resistance Match Between Channels, ∆RON 0.2 Ω typ VS = 0 V to 10 V, IS = −10 mA
0.65 0.8 0.95 Ω max
0.2 Ω typ VS = 3.5 V to 8.5 V, IS = −10 mA
0.65 0.8 0.95 Ω max
On-Resistance Flatness, RFLAT(ON) 12.5 Ω typ VS = 0 V to 10 V, IS = −10 mA
14.5 19 23 Ω max
0.6 Ω typ VS = 3.5 V to 8.5 V, IS = −10 mA
0.9 1.1 1.3 Ω max
Threshold Voltage, VT 0.7 V typ See Figure 26
LEAKAGE CURRENTS VDD = 13.2 V, VSS = 0 V
Source Off Leakage, IS (Off ) ±0.1 nA typ VS = 1 V/10 V, VD = 10 V/1 V, see Figure 31
±1.5 ±5.0 ±21 nA max
Drain Off Leakage, ID (Off ) ±0.1 nA typ VS = 1 V/10 V, VD = 10 V/1 V, see Figure 31
±1.5 ±7.0 ±25 nA max
Channel On Leakage, ID (On), IS (On) ±0.5 nA typ VS = VD = 1 V/10 V, see Figure 32
±1.5 ±5.0 ±21 nA max
FAULT
Source Leakage Current, IS
With Overvoltage ±65 µA typ VDD = 13.2 V, VSS = 0 V, GND = 0 V,
VS = ±55 V, see Figure 35
Power Supplies Grounded or Floating ±49 µA typ VDD = 0 V or floating, VSS = 0 V or floating,
GND = 0 V, EN = 0 V or floating, VS =
±55 V, see Figure 36
Drain Leakage Current, ID DR = floating or >2 V
With Overvoltage ±2.0 nA typ VDD = 13.2 V, VSS = 0 V, GND = 0 V,
INx = 0 V or floating, VS = ±55 V,
see Figure 35
±20 ±30 ±65 nA max
Power Supplies Grounded ±10 nA typ VDD = 0 V, VSS = 0 V, GND = 0 V, VS = ±55 V,
EN = 0 V, see Figure 36
±30 ±50 ±100 nA max
Power Supplies Floating ±10 ±10 ±10 µA typ VDD = floating, VSS = floating, GND = 0 V,
VS = ±55 V, EN = 0 V, see Figure 36
DIGITAL INPUTS
Input Voltage High, VINH 2.0 V min
Input Voltage Low, VINL 0.8 V max
Input Current, IINL or IINH 0.7 µA typ VIN = VGND or VDD
1.2 µA max
Digital Input Capacitance, CIN 6.0 pF typ
Output Voltage High, VOH 2.0 V min
Output Voltage Low, VOL 0.8 V max
Rev. C | Page 7 of 30
Page8
ADG5436F Data Sheet
−40°C to −40°C to
Parameter +25°C +85°C +125°C Unit Test Conditions/Comments
DYNAMIC CHARACTERISTICS1
Transition Time, tTRANSITION 400 ns typ RL = 300 Ω, CL = 35 pF
545 560 570 ns max VS = 10 V, see Figure 46
tON (EN) 435 ns typ RL = 300 Ω, CL = 35 pF
515 530 550 ns max VS = 8 V, see Figure 45
tOFF (EN) 185 ns typ RL = 300 Ω, CL = 35 pF
230 240 250 ns max VS = 8 V, see Figure 45
Break-Before-Make Time Delay, tD 300 ns typ RL = 300 Ω, CL = 35 pF
180 ns min VS = 8 V, see Figure 44
Overvoltage Response Time, tRESPONSE 590 ns typ RL = 1 kΩ, CL = 2 pF, see Figure 39
770 830 870 ns max
Overvoltage Recovery Time, tRECOVERY 680 ns typ RL = 1 kΩ, CL = 2 pF, see Figure 40
850 910 1000 ns max
Interrupt Flag Response Time, tDIGRESP 85 115 ns typ CL = 12 pF, see Figure 41
Interrupt Flag Recovery Time, tDIGREC 60 85 µs typ CL = 12 pF, see Figure 42
600 ns typ CL = 12 pF, RPULLUP = 1 kΩ, see Figure 43
Charge Injection, QINJ −341 pC typ VS = 6 V, RS = 0 Ω, CL = 1 nF, see Figure 47
Off Isolation −68 dB typ RL = 50 Ω, CL = 5 pF, f = 1 MHz, see Figure 33
Channel-to-Channel Crosstalk −70 dB typ RL = 50 Ω, CL = 5 pF, f = 1 MHz, see Figure 34
Total Harmonic Distortion Plus Noise, THD + N 0.007 % typ RL = 10 kΩ, VS = 6 V p-p, f = 20 Hz to
20 kHz, see Figure 38
−3 dB Bandwidth 152 MHz typ RL = 50 Ω, CL = 5 pF, see Figure 37
Insertion Loss −0.8 dB typ RL = 50 Ω, CL = 5 pF, f = 1 MHz, see Figure 37
CS (Off ) 14 pF typ VS = 6 V, f = 1 MHz
CD (Off ) 30 pF typ VS = 6 V, f = 1 MHz
CD (On), CS (On) 41 pF typ VS = 6 V, f = 1 MHz
POWER REQUIREMENTS VDD = 13.2 V, VSS = 0 V, digital inputs = 0 V,
5 V, or VDD
Normal Mode
IDD 0.9 mA typ
1.2 1.3 mA max
IGND 0.4 mA typ
0.55 0.6 mA max
ISS 0.5 mA typ
0.65 0.7 mA max
Fault Mode VS = ±55 V
IDD 1.2 mA typ
1.6 1.8 mA max
IGND 0.8 mA typ
1.0 1.1 mA max
ISS 0.5 mA typ Digital inputs = 5 V
1.0 1.8 mA max VS = ±55 V, VD = 0 V
VDD 8 V min GND = 0 V
44 V max GND = 0 V
1 Guaranteed by design. Not subject to production test.
Rev. C | Page 8 of 30
Page9
36 V SINGLE SUPPLY
Data Sheet ADG5436F
36 V SINGLE SUPPLY
VDD = 36 V ± 10%, VSS = 0 V, GND = 0 V, CDECOUPLING = 0.1 µF, unless otherwise noted.
Table 4.
−40°C to −40°C to
Parameter +25°C +85°C +125°C Unit Test Conditions/Comments
ANALOG SWITCH VDD = 32.4 V, VSS = 0 V, see Figure 30
Analog Signal Range 0 V to VDD V
On Resistance, RON 22 Ω typ VS = 0 V to 30 V, IS = −10 mA
24.5 31 37 Ω max
10 Ω typ VS = 4.5 V to 28 V, IS = −10 mA
11 14 16.5 Ω max
On-Resistance Match Between Channels, ∆RON 0.15 Ω typ VS = 0 V to 30 V, IS = −10 mA
0.65 0.8 0.95 Ω max
0.15 Ω typ VS = 4.5 V to 28 V, IS = −10 mA
0.6 0.7 0.8 Ω max
On-Resistance Flatness, RFLAT(ON) 12.5 Ω typ VS = 0 V to 30 V, IS = −10 mA
14.5 19 23 Ω max
0.1 Ω typ VS = 4.5 V to 28 V, IS = −10 mA
0.4 0.5 0.5 Ω max
Threshold Voltage, VT 0.7 V typ See Figure 26
LEAKAGE CURRENTS VDD =39.6 V, VSS = 0 V
Source Off Leakage, IS (Off ) ±0.1 nA typ VS = 1 V/30 V, VD = 30 V/1 V, see Figure 31
±1.5 ±5.0 ±21 nA max
Drain Off Leakage, ID (Off ) ±0.1 nA typ VS = 1 V/30 V, VD = 30 V/1 V, see Figure 31
±1.5 ±7.0 ±25 nA max
Channel On Leakage, ID (On), IS (On) ±0.5 nA typ VS = VD = 1 V/30 V, see Figure 32
±1.5 ±5.0 ±21 nA max
FAULT
Source Leakage Current, IS
With Overvoltage ±60 µA typ VDD = 39.6 V, VSS = 0 V, GND = 0 V,
INx = 0 V or floating, VS = +55 V, −40 V,
see Figure 35
Power Supplies Grounded or Floating ±49 µA typ VDD = 0 V or floating, VSS = 0 V or
floating, GND = 0 V, INx = 0 V or
floating, VS = +55 V, −40 V, see Figure 36
Drain Leakage Current, ID DR = floating or >2 V
With Overvoltage ±2.0 nA typ VDD = 39.6 V, VSS = 0 V, GND = 0 V,
VS = +55 V, −40 V, see Figure 35
±20 ±30 ±65 nA max
Power Supplies Grounded ±10 nA typ VDD = 0 V, VSS = 0 V, GND = 0 V, VS =
+55 V, −40 V, EN = 0 V, see Figure 36
±30 ±50 ±100 nA max
Power Supplies Floating ±10 ±10 ±10 µA typ VDD = floating, VSS = floating, GND = 0 V,
VS = +55 V, −40 V, EN = 0 V, see Figure 36
DIGITAL INPUTS
Input Voltage High, VINH 2.0 V min
Input Voltage Low, VINL 0.8 V max
Input Current, IINL or IINH 0.7 µA typ VIN = VGND or VDD
1.2 µA max
Digital Input Capacitance, CIN 6.0 pF typ
Output Voltage High, VOH 2.0 V min
Output Voltage Low, VOL 0.8 V max
Rev. C | Page 9 of 30
Page10
ADG5436F Data Sheet
−40°C to −40°C to
Parameter +25°C +85°C +125°C Unit Test Conditions/Comments
DYNAMIC CHARACTERISTICS1
Transition Time, tTRANSITION 400 ns typ RL = 300 Ω, CL = 35 pF
540 555 570 ns max VS = 10 V, see Figure 46
tON (EN) 440 ns typ RL = 300 Ω, CL = 35 pF
520 540 560 ns max VS = 18 V, see Figure 45
tOFF (EN) 160 ns typ RL = 300 Ω, CL = 35 pF
190 195 200 ns max VS = 18 V, see Figure 45
Break-Before-Make Time Delay, tD 330 ns typ RL = 300 Ω, CL = 35 pF
210 ns min VS = 18 V, see Figure 44
Overvoltage Response Time, tRESPONSE 260 ns typ RL = 1 kΩ, CL = 2 pF, see Figure 39
340 360 385 ns max
Overvoltage Recovery Time, tRECOVERY 1500 ns typ RL = 1 kΩ, CL = 2 pF, see Figure 40
2100 2400 2700 ns max
Interrupt Flag Response Time, tDIGRESP 85 115 ns typ CL = 12 pF, see Figure 41
Interrupt Flag Recovery Time, tDIGREC 60 85 µs typ CL = 12 pF, see Figure 42
600 ns typ CL = 12 pF, RPULLUP = 1 kΩ, see Figure 43
Charge Injection, QINJ −627 pC typ VS = 18 V, RS = 0 Ω, CL = 1 nF, see
Figure 47
Off Isolation −71 dB typ RL = 50 Ω, CL = 5 pF, f = 1 MHz, see
Figure 33
Channel-to-Channel Crosstalk −73 dB typ RL = 50 Ω, CL = 5 pF, f = 1 MHz, see
Figure 34
Total Harmonic Distortion Plus Noise, THD + N 0.001 % typ RL = 10 kΩ, VS = 18 V p-p, f = 20 Hz to
20 kHz, see Figure 38
−3 dB Bandwidth 173 MHz typ RL = 50 Ω, CL = 5 pF, see Figure 37
Insertion Loss −0.8 dB typ RL = 50 Ω, CL = 5 pF, f = 1 MHz, see
Figure 37
CS (Off ) 11 pF typ VS = 18 V, f = 1 MHz
CD (Off ) 23 pF typ VS = 18 V, f = 1 MHz
CD (On), CS (On) 36 pF typ VS = 18 V, f = 1 MHz
POWER REQUIREMENTS VDD = 39.6 V, VSS = 0 V, digital inputs =
0 V, 5 V, or VDD
Normal Mode
IDD 0.9 mA typ
1.2 1.3 mA max
IGND 0.4 mA typ
0.55 0.6 mA max
ISS 0.5 mA typ
0.65 0.7 mA max
Fault Mode VS = +55 V, −40 V
IDD 1.2 mA typ
1.6 1.8 mA max
IGND 0.8 mA typ
1.0 1.1 mA max
ISS 0.5 mA typ Digital inputs = 5 V
1.0 1.8 mA max VS = ±55 V, VD = 0 V
VDD 8 V min GND = 0 V
44 V max GND = 0 V
1 Guaranteed by design. Not subject to production test.
Rev. C | Page 10 of 30
Page11
CONTINUOUS CURRENT PER CHANNEL, Sxx OR Dx
Data Sheet ADG5436F
CONTINUOUS CURRENT PER CHANNEL, Sxx OR Dx
Table 5.
Parameter 25°C 85°C 125°C Unit Test Conditions/Comments
16-Lead TSSOP
θJA = 112.6°C/W 113 77 50 mA max VS = VSS + 4.5 V to VDD − 4.5 V
88 61 42 mA max VS = VSS to VDD
16-Lead LFCSP
θJA = 30.4°C/W 207 125 68 mA max VS = VSS + 4.5 V to VDD − 4.5 V
161 103 61 mA max VS = VSS to VDD
Rev. C | Page 11 of 30
Page12
ABSOLUTE MAXIMUM RATINGS、ESD CAUTION
ADG5436F Data Sheet
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted. Stresses at or above those listed under Absolute Maximum
Table 6. Ratings may cause permanent damage to the product. This is a
Parameter Rating stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
VDD to VSS 48 V
section of this specification is not implied. Operation beyond
VDD to GND −0.3 V to +48 V
the maximum operating conditions for extended periods may
VSS to GND −48 V to +0.3 V
affect product reliability.
Sxx to GND −55 V to +55 V
Sxx to VDD or VSS 80 V Only one absolute maximum rating can be applied at any
VS to VD 80 V one time.
Dx Pin1 to GND VSS − 0.7 V to VDD + 0.7 V or ESD CAUTION
30 mA, whichever occurs first
Digital Inputs to GND GND − 0.7 V to 48 V or
30 mA, whichever occurs first
Peak Current, Sxx or Dx Pins 288 mA (pulsed at 1 ms,
10% duty cycle maximum)
Continuous Current, Sxx or Dx Data2 + 15%
Digital Output GND − 0.7 V to 6 V or 30 mA,
whichever occurs first
Dx Pin, Overvoltage State, 1 mA
DR = GND, Load Current
Operating Temperature Range −40°C to +125°C
Storage Temperature Range −65°C to +150°C
Junction Temperature 150°C
Thermal Impedance, θJA
16-Lead TSSOP (4-Layer Board) 112.6°C/W
16-Lead LFCSP (4-Layer Board) 30.4°C/W
Reflow Soldering Peak As per JEDEC J-STD-020
Temperature, Pb-Free
ESD Rating, HBM: ESDA/JEDEC
JS-001-2011
Input/Output (I/O) Port to 6 kV
Supplies
I/O Port to I/O Port 6 kV
All Other Pins 6 kV
1 Overvoltages at the Dx pin are clamped by internal diodes. Limit current to
the maximum ratings given.
2 See Table 5.
Rev. C | Page 12 of 30
Page13
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
Data Sheet ADG5436F
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
D1 1 12 EN
IN1/F1 1 16 SF
S1B 2 ADG5436F 11 VDD
S1A 2 15 FF V 3 TOP VIEW
SS (Not to Scale) 10 S2B
D1 3 ADG5436F 14 EN GND 4 9 D2
S1B 4 TOP VIEW 13
(Not to Scale) VDD
VSS 5 12 S2B
GND 6 11 D2
NIC 7 10 S2A
DR 8 9 IN2/F2 NOTES
1. NIC = NO INTERNAL CONNECTION.
2. THE EXPOSED PAD IS INTERNALLY CONNECTED. FOR
INCREASED RELIABILITY OF THE SOLDER JOINTS AND
NOTES MAXIMUM THERMAL CAPABILITY, IT IS RECOMMENDED
1. NIC = NO INTERNAL CONNECTION. THAT THE PAD BE CONNECTED TO THE LOWEST
SUPPLY VOLTAGE, VSS.
Figure 2. TSSOP Pin Configuration Figure 3. LFCSP Pin Configuration
Table 7. Pin Function Descriptions
Pin No.
TSSOP LFCSP Mnemonic Description
1 15 IN1/F1 Logic Control Input 1 (IN1). See Table 8.
Decoder Pin (F1). This pin is used together with the specific fault pin (SF) to indicate which input is in
a fault condition. See Table 9.
2 16 S1A Overvoltage Protected Source Terminal 1A. This pin can be an input or output.
3 1 D1 Drain Terminal 1. This pin can be an input or output.
4 2 S1B Overvoltage Protected Source Terminal 1B. This pin can be an input or output.
5 3 VSS Most Negative Power Supply Potential.
6 4 GND Ground (0 V) Reference.
7 7 NIC No Internal Connection.
8 5 DR Drain Response Digital Input. Tying this pin to GND enables the drain to pull to VDD or VSS during an
overvoltage fault condition. The default condition of the drain is open-circuit when the pin is left
floating or if it is tied to VDD.
9 6 IN2/F2 Logic Control Input 2 (IN2). See Table 8.
Decoder Pin (F2). This pin is used together with the specific fault pin (SF) to indicate which input is in
a fault condition. See Table 9.
10 8 S2A Overvoltage Protected Source Terminal 2A. This pin can be an input or output.
11 9 D2 Drain Terminal 2. This pin can be an input or output.
12 10 S2B Overvoltage Protected Source Terminal 2B. This pin can be an input or output.
13 11 VDD Most Positive Power Supply Potential.
14 12 EN Active High Digital Input. When this pin is low, the device is disabled and all switches are off. When
this pin is high, the INx logic inputs determine the on switches.
15 13 FF Fault Flag Digital Output. This pin has a high output when the device is in normal operation or a low
output when a fault condition occurs on any of the Sxx inputs. The FF pin has a weak internal pull-up
that allows the signals to be combined into a single interrupt for larger modules that contain
multiple devices.
16 14 SF Specific Fault Digital Output. This pin has a high output when the device is in normal operation, or a
low output when a fault condition is detected on a specific pin, depending on the state of F1 and F2
per Table 9.
EP Exposed Pad The exposed pad is connected internally. For increased reliability of the solder joints and maximum
thermal capability, it is recommended that the pad be soldered to the lowest supply voltage, VSS.
Rev. C | Page 13 of 30
12882-002
DR 5 16 S1A
IN2/F2 6 15 IN1/F1
NIC 7 14 SF
S2A 8 13 FF
12882-103
Page14
TRUTH TABLES FOR SWITCHES
ADG5436F Data Sheet
TRUTH TABLES FOR SWITCHES
Table 8. Truth Table
INx SxA SxB
0 Off On
1 On Off
Table 9. Fault Diagnostic Output Truth Table
State of Specific Fault Pin (SF) with Decoder Pins (F2, F1)
Switch in Fault1 F2 = 0, F1 = 0 F2 = 0, F1 = 1 F2 = 1, F1 = 0 F2 = 1, F1 = 1 State of Fault Flag (FF)
None 1 1 1 1 1
S1A 0 1 1 1 0
S1B 1 0 1 1 0
S2A 1 1 1 0 0
S2B 1 1 0 1 0
S1A, S1B 0 0 1 1 0
S1A, S2A 0 1 1 0 0
S1A, S2B 0 1 0 1 0
S1B, S2A 1 0 1 0 0
S1B, S2B 1 0 0 1 0
S2A, S2B 1 1 0 0 0
S1A, S1B, S2A 0 0 1 0 0
S1A, S1B, S2B 0 0 0 1 0
S1A, S2A, S2B 0 1 0 0 0
S1B, S2A, S2B 1 0 0 0 0
S1A, S1B, S2A, S2B 0 0 0 0 0
1 Note that more than one pin can be in fault at any one time. See the Applications Information section for more details.
Rev. C | Page 14 of 30
Page15
TYPICAL PERFORMANCE CHARACTERISTICS
Data Sheet ADG5436F
TYPICAL PERFORMANCE CHARACTERISTICS
25 40
VDD = +22V TA = 25°C VDD = +15V
VSS = –22V VSS = –15V
V 35
DD = +20V
20 VSS = –20V VDD = +16.5V
V = –16.5V
VDD = +18V SS 30
VSS = –18V
15 VDD = +13.5V 25
VSS = –13.5V
20
10
15 +125°C
+85°C
VDD = +15V
5 10
VSS = –15V +25°C
–40°C
5
0
–25 –20 –15 –10 –5 0 5 10 15 20 25 0
V , V (V) –15 –12 –9 –6 –3 0 3 6 9 12 15
S D VS, VD (V)
Figure 4. RON as a Function of VS and VD, Various Dual Supplies Figure 7. RON as a Function of VS and VD for Different Temperatures,
±15 V Dual Supply
25 40
TA = 25°C VDD = +20V
V = –20V
35 SS
20
VDD = 12V
V = 0V 30
SS
VDD = 10.8V
15 VSS = 0V 25
20
10 +125°C
15
VDD = 13.2V +85°C
VSS = 0V
5 10 +25°C
5 –40°C
0
0 2 4 6 8 10 12 14 0
VS, VD (V) –20 –15 –10 –5 0 5 10 15 20
VS, VD (V)
Figure 5. RON as a Function of VS and VD, 12 V Single Supply Figure 8. RON as a Function of VS and VD for Different Temperatures,
±20 V Dual Supply
25 40
TA = 25°C VDD = 12V
V
35 SS = 0V
20
VDD = 36V
V = 0V 30
SS
15 VDD = 32.4V 25
VSS = 0V
20
10 +125°C
15
+85°C
VDD = 39.6V
5 V = 0V 10 +25°C
SS
–40°C
5
0
0 5 10 15 20 25 30 35 40 0
V , V (V) 0 2 4 6 8 10 12
S D VS, VD (V)
Figure 6. RON as a Function of VS and VD, 36 V Single Supply
Figure 9. RON as a Function of VS and VD for Different Temperatures,
12 V Single Supply
Rev. C | Page 15 of 30
ON RESISTANCE (Ω) ON RESISTANCE (Ω) ON RESISTANCE (Ω)
12882-005 12882-004 12882-003
ON RESISTANCE (Ω) ON RESISTANCE (Ω) ON RESISTANCE (Ω)
12882-008 12882-007 12882-006
Page16
ADG5436F Data Sheet
40 2
VDD = 36V
V
35 SS = 0V
30 0
VDD = +12V
25 VSS = 0V
VS = VD = +1V, –10V
20 –2
IS (OFF) +- ID (OFF) +–
+125°C
15 IS (OFF) –+ ID (OFF) –+
+85°C IS, ID (ON)++ IS, ID (ON) – –
–4
10 +25°C
–40°C
5
–6
0 0 20 40 60 80 100 120
0 4 8 12 16 20 24 28 32 36 TEMPERATURE (°C)
VS, VD (V)
Figure 10. RON as a Function of VS and VD for Different Temperatures, Figure 13. Leakage Current vs. Temperature, 12 V Single Supply
36 V Single Supply
1 5
VDD = +15V
0 VSS = –15V
–1 0
VDD = +15V
–2 VSS = –15V
VS = VD = +10V, –10V –5
–3
–4
IS (OFF) +- ID (OFF) +– –10
–5 IS (OFF) –+ ID (OFF) –+
IS, ID (ON)++ IS, ID (ON) – –
–6
–15 VS = –30V
VS = –55V
–7 VS = +30V
V = +55V
–8 S
–20
0 20 40 60 80 100 120 0 20 40 60 80 100 120
TEMPERATURE (°C) TEMPERATURE (°C)
Figure 11. Leakage Current vs. Temperature, ±15 V Dual Supply Figure 14. Overvoltage Leakage Current vs. Temperature, ±15 V Dual Supply
2 5
VDD = +20V
VSS = –20V
0 0
VDD = +20V
–2 VSS = –20V –5
VS = VD = +15V, –15V
–4 –10
IS (OFF) +- ID (OFF) +–
–6 IS (OFF) –+ ID (OFF) –+ –15
IS, ID (ON)++ IS, ID (ON) – –
V = –30V
–8 –20 S
VS = –55V
VS = +30V
VS = +55V
–10 –25
0 20 40 60 80 100 120 0 20 40 60 80 100 120
TEMPERATURE (°C) TEMPERATURE (°C)
Figure 12. Leakage Current vs. Temperature, ±20 V Dual Supply Figure 15. Overvoltage Leakage Current vs. Temperature, ±20 V Dual Supply
Rev. C | Page 16 of 30
LEAKAGE CURRENT (nA) LEAKAGE CURRENT (nA) ON RESISTANCE (Ω)
12882-010
12882-011 12882-009
OVERVOLTAGE LEAKAGE CURRENT (nA) OVERVOLTAGE LEAKAGE CURRENT (nA) LEAKAGE CURRENT (nA)
12882-015 12882-014 12882-012
Page17
Data Sheet ADG5436F
2 0
VDD = 12V
0 VSS = 0V TA = 25°C
VDD = +15V
–20 VSS = –15V
–2
–4 –40
–6
–60
–8
–10 –80
–12 VS = –30V
V = –55V –100
–14 S
VS = +30V
VS = +55V
–16 –120
0 20 40 60 80 100 120 10k 100k 1M 10M 100M 1G 10G
TEMPERATURE (°C) FREQUENCY (Hz)
Figure 16. Overvoltage Leakage Current vs. Temperature, 12 V Single Supply Figure 19. Channel-to-Channel Crosstalk vs. Frequency
2 800
VDD = 36V TA = 25°C
V = 0V
0 SS 700
600
–2
500
–4
400
–6 300
–8 200
–10 100
V = –38V VDD = 12V, V = 0V
S SS
V = –40V 0 V = 36V, V = 0V
–12 S DD SS
VS = +38V
VS = +55V –100
–14
0 20 40 60 80 100 120 –200
TEMPERATURE (°C) 0 5 10 15 20 25 30 35 40
VS (V)
Figure 17. Overvoltage Leakage Current vs. Temperature, 36 V Single Supply Figure 20. Charge Injection vs. Source Pin Voltage (VS), Single Supply
0 900
TA = 25°C T
V = 15V A = 25°C
DD 800
–20
700
600
–40
500
–60 400
300
–80 200
VDD = +15V, VSS = –15V
100 VDD = +20V, VSS = –20V
–100
0
–100
–120
10k 100k 1M 10M 100M 1G 10G –200
FREQUENCY (Hz) –20 –15 –10 –5 0 5 10 15 20
V (V)
Figure 18. Off Isolation vs. Frequency S
Figure 21. Charge Injection vs. Source Pin Voltage (VS), Dual Supply
Rev. C | Page 17 of 30
OFF ISOLATION (dB) OVERVOLTAGE LEAKAGE CURRENT (nA) OVERVOLTAGE LEAKAGE CURRENT (nA)
12882-017 12882-016
12882-018
CHARGE INJECTION (pC) CHARGE INJECTION (pC) CHANNEL-TO-CHANNEL CROSSTALK (dB)
12882-021 12882-020
12882-019
Page18
ADG5436F Data Sheet
0 490
TA = 25°C VDD = +12V, VSS = 0V
–100 VDD = +15V V = +36V, V = 0V
VSS = –15V 480 DD SS
–200 WITH DECOUPLING CAPACITORS VDD = +15V, VSS = –15V
VDD = +20V, VSS = –20V
–300 470
–400 460
–500
–600 450
–700 440
–800
430
–900
–100 420
10k 100k 1M 10M 100M 1G –40 –20 0 20 40 60 80 100 120
FREQUENCY (Hz) TEMPERATURE (°C)
Figure 22. ACPSRR vs. Frequency Figure 25. tTRANSITION vs. Temperature
0.020 0.9
LOAD = 10kΩ VDD = +12V, VSS = 0V, VS = 6V p-p
T = 25°C VDD = +36V, VSS = 0V, VS = 18V p-p
A VDD = +15V, VSS = –15V, VS = 15V p-p
VDD = +20V, VSS = –20V, VS = 20V p-p
0.015 0.8
0.010 0.7
0.005 0.6
0 0.5
0 5 10 15 20 –40 –20 0 20 40 60 80 100 120
FREQUENCY (kHz) TEMPERATURE (°C)
Figure 23. THD + N vs. Frequency Figure 26. Threshold Voltage (VT) vs. Temperature
0
TA = 25°C T
–0.5 VDD = +15V SOURCE
VSS = –15V
–1.0
–1.5 VDD
–2.0
–2.5
–3.0
–3.5
2
–4.0 DRAIN
–4.5
–5.0
10k 100k 1M 10M 100M CH1 5.00V CH2 5.00V M400ns A CH2 10.1V
FREQUENCY (Hz) CH3 5.00V T –10.00ns
Figure 27. Drain Output Response to Positive Overvoltage
Figure 24. Bandwidth vs. Frequency (DR Pin = Floating or High)
Rev. C | Page 18 of 30
BANDWIDTH (dB) THD + N (%) ACPSRR (dB)
12882-024 12882-023 12882-022
THRESHOLD VOLTAGE, VT (V) tTRANSITION (ns)
12882-027
12882-026 12882-025
Page19
Data Sheet ADG5436F
24
TA = 25°C
VDD = +10V
20 VSS = –10V
DRAIN 16
1
12
DISTORTIONLESS
8 OPERATING
VSS REGION
4
SOURCE
0
CH1 5.00V CH2 5.00V M400ns A CH2 –14.7V 1 10 100
CH3 5.00V T –10.00ns FREQUENCY (MHz)
Figure 28. Drain Output Response to Negative Overvoltage Figure 29. Large Signal Voltage Tracking vs. Frequency
(DR Pin = Floating or High)
Rev. C | Page 19 of 30
12882-028
SIGNAL VOLTAGE (V p-p)
12882-029
Page20
TEST CIRCUITS
ADG5436F Data Sheet
TEST CIRCUITS
VDD VSS
0.1µF 0.1µF
NETWORK
V ANALYZER
DD VSS
VOUT
SxA RL
50Ω
RL Dx
50Ω SxB
V
VS
GND
Sxx Dx
V IDS V
CHANNEL-TO-CHANNEL CROSSTALK = 20 log OUT
S RON = V/IDS VS
Figure 30. On Resistance Figure 34. Channel-to-Channel Crosstalk
IS (OFF)
A SxA ID (OFF)
Dx A
SxB IS ID
A
A Sxx Dx A
V R
S VD |VS| > |V L
DD| OR |VSS| 10kΩ
Figure 31. Off Leakage Figure 35. Switch Overvoltage Leakage
NC SxA ID (ON) VDD = VSS = GND = 0V
Dx A
A SxB IS ID
A Sxx Dx A
IS (OFF)
VS VD R
V L
S 10kΩ
Figure 32. Channel On Leakage Figure 36. Switch Unpowered Leakage
VDD VSS
0.1µF 0.1µF VDD VSS
0.1µF 0.1µF
NETWORK
V V ANALYZER
DD SS NETWORK
V V ANALYZER
DD SS
Sxx 50Ω
INx Sxx
V 50Ω
S INx VS
Dx
V VOUT Dx
IN RL V VOUT
50Ω IN R
GND L
GND 50Ω
VOUT
OFF ISOLATION = 20 log V VOUT WITH SWITCH
S INSERTION LOSS = 20 log
V
OUT WITHOUT SWITCH
Figure 33. Off Isolation Figure 37. Bandwidth
Rev. C | Page 20 of 30
12882-032 12882-031
12882-030
12882-033
12882-035
12882-036
12882-037 12882-034